I just got my rollers from etsy .. i gotta do the same thing… Cricut needs to find a solution because when I called they offered me $50 off a new machine… like no!!! If everyone is having these wheel issues figure something else out

@keepingupwithdesjo

Жыл бұрын

Yes they really do! Smh. Hope it works out for you

@alejandraespitia2966

Жыл бұрын

50 dollar wow that is better than me all I got was 20 dollars 😅

@terriwilson1441

11 ай бұрын

I just got off the phone with customer support and they said the same thing! Like Sir, that’s not in my budget.

@destamuse

11 ай бұрын

💯 agreed.

@destamuse

11 ай бұрын

💯 agreed!!!

Omg 😮 around the 4min mark you had me nervous. I was like OMG please let her remember where everything goes back to. As someone with a Cricut, I would be too scared to do it myself but I know once you put your mind to it, it can be done with the help of KZread University. Your perseverance as well shows why you are successful. You took me on an emotional ride 🤔😮🫣🫢😬😆 🙌🏾👊🏾. Thanks for sharing, I’m glad it all worked out 👍🏾

@keepingupwithdesjo

Жыл бұрын

Thanks for watching! Yes I was nervous too 😬 so glad I remembered lol

@evanshannon

11 ай бұрын

Word of advice--if you do something like this, record it! That way you have video instructions for how things go back together.

Not me being nervous from start to finish 😂😂😂! You go girl!!

You did it!!! Success baby 🙌🏽. Great job niecey pooh!

@keepingupwithdesjo

Жыл бұрын

Thank you auntie!! ❤️

OMGEEEE I love your DIY video. Your facial expressions and comments along the way are a hoot! I'm not so sure I'll be able to deal with this task as well as you did. I'll have plastic chips and wires all over the place, and I will spew out words worse than a sailor. I'm going to have to ponder this a bit. Maybe I'll step one up and get the Cricut 3. Hmmm....

Remind me not to call you to disarm a bomb! 😂😂😂I just knew you were about to buy a new machine! Proud of you. You on the job and did an outstanding job. Congratulations!

@keepingupwithdesjo

Жыл бұрын

😂😂 Thank do you so much for watching!

I did it🙏Than You so so much girl. Many Blessings.

How did you get the bar out? Did you remove the white wheel?

Definitely A success it works ,Thank you for sharing Greatly Appreciated!!!!!!!!!! Continue to be Great !

@keepingupwithdesjo

Жыл бұрын

Thanks for watching!!

honestly though, Cricut should really think about using products you don't have to replace such as these. This is completely insane! Going to go back to Silhouette Cameo. Thanks for your hard work. geez....

@keepingupwithdesjo

Жыл бұрын

Yes seriously! Thanks for watching

@melissagraham6180

6 ай бұрын

Yessss, what was Cricut thinking?! I just replaced mine using this and a couple of other videos and it was awful. Not gonna lie.

Hello, what is the link? Where did you get the tutorial to replace the rubbers? From what you can see it is a very common problem. Thank you

Question , download the new update now my cricut won’t load shapes , objects to canvas any ideas? Windows 10

Good job!!! I just fixed mine as well and its like having a new machine - but had a miserable time while doing it, super nervracking, never doing it again.

@keepingupwithdesjo

Жыл бұрын

Thank you!! Same, I’m never doing this again but I’m glad I fixed it lol

How did you get that white gear off

How did you get the big white roller/circle off?

@erinshaw5719

11 ай бұрын

Came here for this! Mid-repair and no one shows how it comes off.

@cdcottam1

4 ай бұрын

Did yall ever figure it out?

Nicely done 👏🏽👏🏽👏🏽

That was great ..I have just ordered some bushes

You're so dope, I'm glad you were able to get it done 🙏🏾👍🏾

@keepingupwithdesjo

Жыл бұрын

Thanks for watching!

Girrrl, you had me cussing for you! Whew! I'm stressed. The rollers on my Joy are giving out and I just bid on a new one on EBay. I think that spending the money on a new one is less stressful than what I just watched you do. Lol!

I just changed mine. I almost gave up until I saw your video. I said if she can do it I can too 😂 It’s working now, but I think I touched a wire or something, cuz the lights aren’t coming on. But that’s fine , it’s cutting just like new 😅

@keepingupwithdesjo

Жыл бұрын

Yess!! So happy you finished it lol I was definitely feeling defeated during this. But hopefully the light will come on eventually! lol

You did it ❣️❣️❣️🎉🙏🏻 thank you ❣️

Thank you for sharing this video 🙏🏻

Thanks for showing how to get the roller bar off. Other videos didn't show that part! I have a 3D printer and TPU so I should be able to replace them without further cost. :)

@keepingupwithdesjo

Жыл бұрын

Awesome! Hope it goes well for you

I did this for my spouse's aunt. There were some foul language involved, but I think the most difficult part were the screws underneath the top of the casing. Not a lot of room for a tool. Found it easier to hold the screwdriver tip in the racket adaptor and twist it by hand.

@keepingupwithdesjo

10 ай бұрын

Lol! Glad it worked out for you

I have been thinking about doing mine and your video is the first one I've watched.... as soon as you started, I was like well ill be buying a new one....😂 -the last few seconds of the video was the only time I was like maybe I could try this.... 😥

Is this a maker 3??

Zero out of ten killed me. Exactly that. I have screws can’t find homes. Ruined the springs lol. Praying it works again 😭😭😭😭

This made my day 😂 🫶🏼 I recommend 0 out of 10 as well, those E-clamps almost took me out 🪦☠️😅😂 I just finished replacing my wheels, thank you for this video 💗

Bless your patience. I came here because my rollers for me FUCKED up. It’s chewed up TWO of my mats. I may attempt doing this switch out. But if not I’m throwing hands with Cricut.

How did you get the white whell off? I'm not getting it off and it wasn't shown in the video?

@keepingupwithdesjo

Жыл бұрын

I think I just wiggled it around. I didn’t get it all the way off. I pushed it far enough to get the other pieces off

Thanks for walking on faith and sharing how you replaced the Cricut Maker rubber rollers! You are truly a Cricut Maker saver...😍🤩🙌

@keepingupwithdesjo

11 ай бұрын

Thanks for watching!

@aleciatyler512

11 ай бұрын

@@keepingupwithdesjo ❤

Way to go!!!!!

Thanks for an honest review of doing this repair. Is your repaired cricut still working?

@keepingupwithdesjo

Жыл бұрын

Yes it’s working perfectly!

@ritas6972

Жыл бұрын

@@keepingupwithdesjo Wonderful! Thank you!

@shanatownsend3602

3 ай бұрын

@@keepingupwithdesjo. Hello. Did you remove the screws from the inside of the cricut, or only the screws on the bottom of the machine?

Whats the worst part is unscrewing that top lid bc you need a small screw driver that can fit underneath, i used a small drill bit wraped in paper towel. THIS WAS SO FRUSTRATING. thank you for walking me through it.

Gurl I was nervous for you and can you share the video you were looking at to fix it? You dope and that's what im talking about.

I have to replace my rollers too and I ordered them from Amazon and they cannot fit...I offered to send me a new set and they cannot fit...I order them from Ebay and they came in today same issue...how did you heat them up to get them to fit?😮

@keepingupwithdesjo

Жыл бұрын

You have to warm them up in a cup of water for a couple of seconds! I hope they work for you

SUCCESS!! So glad I found your video… I’m replacing my rubber rollers as I speak… got everything open and now dealing with getting the actual bar out the left side. Might have to watch this another time… 😂 UGH!! Wish me luck!!

@keepingupwithdesjo

Жыл бұрын

Thanks for watching!! Lol! I hope you got it fixed love!

@crayzed18

8 ай бұрын

Currently my struggle. I cannot get the bar out AT ALL 😭😭😭

@kathym.50

5 ай бұрын

My struggle as well uggghh

how did you get the new rollers on? Mine are super hard like yours. I know you said you were going to heat them up, can you please elaborate?

@keepingupwithdesjo

Жыл бұрын

Hey there. I didn’t end up heating them up I tried to put them in hot water but it didn’t work. So I just used a cloth to push it down and slide it on , I struggled a bit but I got it on.

@Lh2bme

Жыл бұрын

The ones I bought said boiling hot water, but you could probably try a heat gun on low. PVA filament that a lot of 3D printers use are easy to heat up with a heat gun.

@Pretear521

Жыл бұрын

@@Lh2bme i ended up putting in boiling water..it literally took 5 minutes to get both on. I had wasted like 4 hours already trying to brute force then on 😆 my poor hands

Hello, how did you get the wheel off the left side of the machine?

@heidistickney8743

Жыл бұрын

We took an exacto knife and shaved off the corners of the white piece to get the wheel off!

@keepingupwithdesjo

Жыл бұрын

I’m honestly not sure. I did a whole lot of wiggling! & I don’t think I completely took the wheel off

How did you manage to get the 2nd bracket off with the tiny wheel in the way. I can't get the e clip off.

@jenco7867

Жыл бұрын

I'm curious about this as well...I somehow managed to get the big white wheel off but I can't get the other clip off to get the left side of the bar out

@Lh2bme

Жыл бұрын

@@jenco7867 I managed this. So basically you will want to take the screws out of the white bracket in the front of the tiny wheel. This will be handy later. You'll need to shimmy the roller a bit but e clip will get a bit loose. If you push the bar towards it. Now once you pushed it to you, take a pliers or a very tiny flat head and put it in the clip. You'll notice it has a little gap close to the bar. Pop it off. May take a bit of patience. Once it's off, you may or may not be able to remove the clip. For me, I just loosened it and popped the bar out by shimmying it to the opposite side. Now you will need to use hot water to put the rollers on. I heated up a glass of water in the microwave and then soaked the rollers on the bar. It got soft after a minute and moved a bit easier. One thing I will say is that reassembly is a pain! You want to put the bar on the right then shimmy it into the housing. Readd both clips and then the e clips and then the springs. If you do the left spring first the e clip may not go back on. Also if you drop the e clip behind the tiny wheel don't panic. I did this. Simply get an extra helper to gently push the bottom of the housing and use some tiny tweezers to retrieve it. Then put it back on. Hope this helped.

@Lh2bme

Жыл бұрын

If you need more help, please let me know. I just fixed mine today

@oliviahart15

Жыл бұрын

How did you get your bar back into the gold bracket thing? I can’t get mine to go back on

Your Fu*k*n awesome chickee Thank you so much for the video

Curious to know if you're still having issues? I'm about to fix mine... And I have a 3D printer so I'm going to replicate them and save some for nex time.

@keepingupwithdesjo

Жыл бұрын

It’s working perfectly now! I haven’t had any issues since doing this. Good luck!!

they look just mine and can you get the rod aswell

@keepingupwithdesjo

Жыл бұрын

Good luck! & I’m honestly not sure if they have the rods you can buy.

Wow I don’t think you should do it again either I can’t believe how rough you were on everything and that angled screw driver! The best part was when we all watched you watch another video 😂

Did the same thing and got it done. I will never do it again either. Too bad we got no help from cricut! I also took pics every time I had to remove anything so I could see where they were when I had to put it back together!

@keepingupwithdesjo

5 ай бұрын

That’s so smart I definitely should’ve did that! Lol glad it worked for you

@cdcottam1

4 ай бұрын

This is an excellent idea! Thank you!

I failed. I got the rubber on and lost one of the c clips. 🤦🏾‍♀️

Thanks for posting this video. You did an awesome job putting new rubber rollers on and putting it back together. I followed your video and successfully and put new rubber rollers on my machine. Thanks!

@keepingupwithdesjo

Жыл бұрын

Awesome!! Thanks for watching! Glad you were able to fix yours.

How did you get that big wheel off

@keepingupwithdesjo

Жыл бұрын

I didn’t take it completely off I just wiggled it around until I got the other pieces off

@ynellirosas

Жыл бұрын

@@keepingupwithdesjo hey!!! thank you! OMG, i was able to fix my cricut and hold off on the buying a new cutter

@keepingupwithdesjo

Жыл бұрын

@@ynellirosas yay! So happy it worked out for you!!

Can you link the vid you were watching?

@keepingupwithdesjo

Жыл бұрын

It’s in the description!

I used some foam double sided adhesive tape and hot glued it in place. Then I pushed the little white thing with the grooves up beside where the rubber was replaced with the tape and hot glued it there. Worked great, cost $1, and I didn’t have to take apart the machine.

@yvettesalinas6784

Жыл бұрын

Can you post a picture of what it looks like?

@BlondeIntelligence

Жыл бұрын

@@yvettesalinas6784 yes as soon as I get home.

@TheRoseteach

8 ай бұрын

@@BlondeIntelligencehello, Did you post your replaced roller video?

@BlondeIntelligence

8 ай бұрын

@@TheRoseteach not on my channel, it is music industry only. But yes to individuals who reached out

@heidiholliday7337

7 ай бұрын

I would love to know how this worked too!

Ok. I officially hate Cricut for this. But you did a great job.

I did it but the Matt it’s not going

@shehasthekeys

Жыл бұрын

Oh bet, I'm trying this because getting Cricut Support was an epic fail. Thanks!

Wow! If someone with a hammer, a screwdriver, and a pair of pliers can fix this, then I should be able to do it, too.

@keepingupwithdesjo

Жыл бұрын

yep! Give it a try!

"I would just buy a whole new one" that's what they want, those rollers should be metal or much harder rubber...but they design it to fail so you have to buy a new one...and you'll see on most of them that they fail after the warranty period, so you don't get new shit.

That was super entertaining. Looks like a success. Any updates?

@keepingupwithdesjo

8 ай бұрын

It’s still working fine!

👏👏👏

Yo hago eso la dano y boto a la basura jejejej

OK It has been just over a year since making this video.... how long did it hold up? Did it actually work? Thank you! I called Cricut and they offered me $50 toward a new Cricut! On a $400 machine that only comes with a 1 year warranty. Man, that is just wrong! I am so mad right now. Their functional obsolesces is going to fill our landfills faster than plastic...over a $10 pack of rubbers!! Shame on you Cricut!!! Do you by chance have a video on how to completely repair the machine?

More power to you for taking your Maker apart to put on the rubber on…oh HELL NO! I’ll send that S.O.B back to Cricut for them to fix!

@starsshinebrite

10 ай бұрын

They won't fix them. That's the issue.

Wow I have been doing this little by litter for over a month now. Is an impossible mission 😫😫😫

Girl because I’m ready to sell it as is and buy a new one! I’m going to give it one more try. Jesus be with me

@keepingupwithdesjo

Жыл бұрын

Yess give it one last try before you do!

Im so nervous I’m about to try this!!! 😨

@keepingupwithdesjo

10 ай бұрын

Give it a try!!

I swear they revenge glued my machine together. I can’t get past the lid cover 😢

@keepingupwithdesjo

Жыл бұрын

omg! I hope you can get it open!! Make sure you take those extra tiny screws out

The abuse was real asf. 😭 You was not playing when you said if all goes wrong you just gon buy a new one. 😅

@keepingupwithdesjo

6 ай бұрын

😂 exactly!

See what all you don't understand is it was already broken so she had nothing to lose & everything to gain. I didn't think she was going to get it done but she hit it out of the park, nice job.

@keepingupwithdesjo

10 ай бұрын

Right lol. Thanks!

Omg no 😣😓 I either send it to cricut Dr for $130 or just buy. New one

It's is a lot of work and I'm about to do that because i can not afford to purchase another machine. Now what is missed up is that Cricut KNOWS that this is a major problem, So why not make it earlier to replace this part.

Mines are a mess, all the struggle you when through makes me just want to buy a whole new machine lol

@keepingupwithdesjo

Жыл бұрын

😂 yes if I failed I definitely was just gonna buy a new one

@jray5907

Жыл бұрын

@@keepingupwithdesjo I ended up just buying the joy since I needed it for a small project. I'll try and fix it in the future when I have patience 😅

Got mine apart …. Stupid replacements don’t fit….

@keepingupwithdesjo

Жыл бұрын

Oh no! I’m sorry it didn’t work for you.

Not me thinking I should just replace the whole cricut watching this lol

@keepingupwithdesjo

Жыл бұрын

It’s definitely the easier route lol 😂😂

@Pixieshandcrafteddesigns

Жыл бұрын

@@keepingupwithdesjo thankfully mind just slid over. I popped a flat head screwdriver under the bar for leverage and slid it over where it’s supposed to be.

lol this video crack me up. As rough as she was with it…just buy a new one 😂

@HealingOfTheHood

3 ай бұрын

That thank you Jesus part tho 💪🏽

Note to self: I don’t have the ability to do this. Just save for a new Cricut. 😬

I think I'm going to watch someone else's video. I can't afford to break my machine. I need it.

@keepingupwithdesjo

4 ай бұрын

Definitely! This wasn’t a tutorial I don’t want you to break your machine. Lol hope it works out for you!

This is some bullshit. I can’t believe all that is involved with changing two rubber rollers! 😫😭

@keepingupwithdesjo

4 ай бұрын

😂😂 too much.

You did a tutorial on how to replace the rubber roller by watching on youtube a video on how to replace a rubber roller? Is like you watching your own video on how to replace it 🤣 doesn't make any sense 🤣🤣🤣

@keepingupwithdesjo

Жыл бұрын

This video wasn’t a tutorial if you actually watched the video.

@daniellescholfield2489

10 ай бұрын

Either way it is a great video. You motivated and unmotivated me all in 1. Just cut one of my rollers off because it felt dry rotted then thought shit I probably shouldn't have don't that 😅