love waking up to a mopboyz vid

@MOPBOYZ

2 ай бұрын

my dude🤝

@snoopysrc

Ай бұрын

​@MOPBOYZ awesome video check out my isinwheel s9max electric scooter that's my ride I get around town on

F12 is a certified ripper😍! Small side notes: The bog from the start might be the shimming, belt not going it's full travel. Or it would prefer 4-4.2gram rollers. A lot of new S6 R1200 / R1400 / R/T MK2 exhausts leak from the silencer. In Europe we just put gasket maker on it, let it cure for a couple hours and go full throttle. Sounds a bit ghetto but it works. Waiting on that disc brake conversion!!

lose the stage six exhaust get an yasuni c21 ! , carb air screw 1 1/2 turn. try and get full malossi overrange. if you want to go full wheely mode get and polini speed control vario. nice bike you have there! i owned 2 my self.

Good job ! This is a very nice and taste tuning on this scooter . Keep up the good work !

When the wind slows you down faster than the brake 🤣🤣❤️🇬🇧

What a ripper such a nice bike can't wait to see it dialed in 100%

that thing rips, good job on the build

Hey brother, watching from Puerto Rico, I have a F12 LC foggy. I've just finished watching the whole series and you have motivated me to build mine. Haven't even started in years, so wish me luck 😅

I get so excited over these ped build now haha. Love these vids man

The F12 is my fave - love the Foggy rep. My Ludix Blaster runs a very similar rads and header tank set up. For easy bleeding just prop up front wheel and give it a few braaps with the tank cap off. Usually gobbles down another 200-300ml of coolant. Careful running too cold, chance of cold seize. Consider a thermostat 👍 great vid

Been waiting all week for this one to drop its a beast 💪

Hey man, greeting from Italy. Those things (Yamaha Aerox (GP1) and Yamaha BW’S as well) were all the rage in the 2000s. Some tips, a common mod back in the day was to install a GP1 radiator as well, in order to get usable temps on higher end cylinders. Also, as you already noticed, you should get the rear brake situation sorted out. Idk if you know this, but the Phantom was also sold with a read disk brake, you could try to get the casing with the disc and caliper mounts, as I don’t know if adapting a disc setup was possible with the drum brake casing

Awesome content keep it up, phantom looks beautiful...

@MOPBOYZ

2 ай бұрын

thanks my dude

Love seeing new episodes

It's always a good day with another MOPBOYZ upload

@MOPBOYZ

2 ай бұрын

my guy 🤝

Just checked out this channel for the first time today, been wanted to build up a scooter to mess around on. Then I saw that EZ90 cub you got, that thing is clean! Been looking for one nothing in my area unfortunately

Yess!!! Getting me pumped on sr50 of similar build going rn!

Finally been looking for a banger vid

@MOPBOYZ

2 ай бұрын

😤😤

new road 100cc the second tune you made with the stiff contrast spring is actually most of the tunes you can hear in a '' 100cc malossi trofeo '' races , they get all the torque for those sketchy curves in the Magione track , you got that sweet spot with the soft contrast and it really fits on a 70 cc , altough a stiffer one is better from 86 cc and above

insane build ! good shit I live in vegas but I grew up in france and used to own a mbk booster with a malossi MHR 70cc, Malossi MHR exhaust, internal rotor ignition MVT, stage 6 crankshaft, transmission kit overrange MHR and a carburator PWK 26, this thing was flying, I always wanted to try to swap it to liquid with a mbk nitro engine but I grew up and left my scooter behind haha Love your channel, it makes me wanna buy one again and im 34 yearsold today haha keep up the good work man !

I' m from Romania and I love to watch your videos . Respect man. :-) 😀

Ripper is Born 💯💯 Love it!

Great job on that swap! That thing gets it! 👍👍 Maybe you could send that pipe back for a new one. Doesn't seem right to be leaking from the get go. Seeing those fancy rear wheel stands, makes me wonder why manufacturers ever went away from the center stands on bikes. My '67 and '69 Honda Trail 90's both have the center stand, and they are awesome for working on the bike.

Great vid bud!!

so cool man. plus that thing sound awsome🔥

@MOPBOYZ

2 ай бұрын

thanks dude!

Been waiting for this video so bad

Killer f12 that boi sick🚀

Bro, I love these scooters. I’m gonna have to buy one one of these days.

100k bro insane

congrats to 100k, yuo should amke some sweet merch, i would 100% buy it

What a beast, and the wind was wild the otherday.

Sounds really, really good. 👍 👍 👍

how do you break in a new top end ive just got one for my gilera just wondering if you do heat cycles and how thnaks

What did you use for your light replacement. Did you only change bulbs or sockets also. I need to for my 2001 F12 LC DD and 2003 f12 LC DD

Sounds Sweet 👽👍🏻

Man that dog rolls. Hold on to her trev.. mop boys forever..old man mop 😊

@MOPBOYZ

2 ай бұрын

thanks man🤙

i have an inner rotor kit with no charging, how do you change the wiring so that the lights run off of the 18v battery, would help alot as i have to charge my motorcycle battery every 2 days to keep it fully charged.

I need storage bins like that! My garage looks messy on my channel! Smh.

I love your Videos best Scooter Channel Out there greetings from Germany

hey man just noticed after watching this video for the 100th time you are still running af vacuum fuel system. You have to upgrade that to a better "petrol tap" I would suggest the malossi one. because the vacuum system cannot keep up if your riding full throttle for to long and that will result in the bike bugging out and run lean and foul your spark plug or destroy your piston. but a really nice video greetings from Denmark

actually i have got an f12 liquid cooled from the factory , i think the frame is a little different because that coolant reservoir actually mounts inside the glove box

Hey, I also have a problem on ma ac minarelli with the drum brake, It is also very bad and i've done everything a brake line, pads, double spring, even switched to another wheel and it is good for 2-3 days and then it just disappears. Will switch to a rear disc brake

Hey mate love the build I’ve done exactly the same on an air cooled Zip. Malossi overrange instead. Blue contra and half mix 4.5 and 4.7g rolls. Rpm hovers around 11,600rpm, only other difference is a Malossi Mhr team pipe. I would have thought you would want to be just under 12,000rpm seeing your using the R1200 pipe. Where are you at now with rpm?

hello bro i love wathcing ur videos i got 1 question i have a kymco agility 50cc 4stroke and im tryna put a malossi 88cc sport cilynder can u tell me how much kmh i hit if i put that malossi cilynder in?

Have a malaguti f12 phantom,problem either front brakes,piston is sticking how to disassemble to fix

Goooood 🙌🏽❤️

Damn son, I thought my old F12 that did 120km/h was badass, this is on another level ❤

Whats your cvt setup, like rollers springs and clutch?

honey wake up the mopboyz just posted

Honey wake up mopboyz has posted!!

sounds nice

How do you think the S6 MK2 would go in a prebug? Bit much?

What led bulbs did you use explain please

Never doubt a malaguti scooter they are aswome

Have you tried using some Red armor 2 stroke motor oil in your 🛵 scooter? If it's A 2 stroke engine? on your scooter that is in the video you're doing on the that engine build.

Nice!

bros consistent with the lunch break uploads

HEY SCOOTER FREEEEEAK 🤪IM LOVING THE F12 BUILD ,GREAT TO SEE YOU,VE GONE TO LIQUID COOLING .SURE LOOKS MEAN IN RED & THOSE LIGHTS ARE REAL STRONG .IM BUILDING A F15 FIRE 🔥 FOX 🦊 SO IM PAYING CLOSE ATTENTION.NICE TO SEE YOUR RUNNING A DECENT CASTOR BASED OIL JUST MAKE SURE ITS MIXED WELL IF YOU FILL UP ⬆️ AT THE GAS STATION.DONT WASTE THAT CRISPY ENGINE DADDYO 😊

Sick dude!!! Also a rare find this day here in europe... i still own my firefox f15 from when i was 16 years old wich is already 17 years ago lol iam gettin old dude.. iam still running the mk1 stage 6 racing on it wich is 14 years old now but mine has a 2 piece cylinder head.. is that the difference between the mk1 and mk2? mine really go's the block, and the cylinder are tuned by xsh back then those stage6's racing ones can really put out crazy amount of power..

the cap for the reservoir is identical to the one on a stock derbi senda, you can buy them new all over europe.

@MartZilka

2 ай бұрын

hes from the states

@YZbonde

2 ай бұрын

@@MartZilka he often buys from Oversæt as far as Im concerned

Why didnt you put the malossi rc1 on the malleguti

If you go to some where that sell plastic single brick covers 9×4inch think they do them in Aliminum aswell They will look good instead of holes there dirt cheap what they are for is going over the air brick in a house stops mice getting in

i ride cpi gtr 50 cc 2005 it goes 70 km/gh or 45 under my weight love your content btw

How did you import one of these?

i love your videos dude keep it up man and i have a qusten what is the best ubgrade for my zuma

@MOPBOYZ

2 ай бұрын

best upgrade is the cvt!

Shes a beauty, I got rid of my Aerox and got a 2017 runner sp

how much is the fuel consumption with this setup?

I'm missing a stage 6 subframe. allowing your carburetor to be mounted directly above your rear wheel.greats from Amsterdam the Netherlands

She's a ripper🤘

Trying to get an f12 or a jog just like yours 🔥

MOPBOYZ!

there is also the opportunity to install the carburetor to the rear. there is a special subframe that makes that possible. looks good when installed. have it also on my aerox and sr50. keep up good work - the ducati version looks awesome.ah and i forgot. i wont reccomend stage6 parts. the exhausts are quiet cheap stuff in quality. we here in germany (home of s6) had alot of those pipes... quality is bad, price is high - i recomend yasuni

Question please: I have a 06 BWs, will be putting a Polini 70cc head on this summer. Will up the jet by 10% and have a temp gauge. Do I need to suppliment my 2T oil by a little premix? or will my oil pump handle it? Thanks so much, love your content.

@kristers-eb6xb

2 ай бұрын

i highly reccomend you get rid of the oil pump, i wouldn't want to risk my motor, if the pumps fails, but i don't think you will need to add any more oil, except add some for the breaking in phase

@bobloblaw204

2 ай бұрын

@@kristers-eb6xb Thank you so much!

In the future you could maybe do tuning on an Longjia Firefox 4 stroke😂

doubled the power(again)😂❤🔥

Wait!!! You charge the battery when you run?

Bangerrrrrr ;)

i sent a DM on instagram about the regulator setup for the makita battery- im also running a makita battery on my KTM 150, but my lights just explode because its extracting 18v (i have a regulator lying around, just need to know how to wire it)

ya boi using motogp racing technigues on a moped with parachuting... Lets see the full chute with the Doctor's dangle on entry next :)

Miss the Durango ymca days man

Hey man, when the scooter pulls up on the backwheel and you let go off the gas then it sound like its dying. How to fix that?

@MOPBOYZ

2 ай бұрын

more cvt tuning!

@emilsteenvilladsen2669

2 ай бұрын

thanks!@@MOPBOYZ

You should also buy a Yamaha Aerox, also called MBK Nitro. I'd love to see a video of that one.

Hallo, which Main jet and second jet Are u using ? Greetz Stage6RoxXx

🔥

The back brake issue. Have you tried taking the pivot arm off the splines and adjusting it that way ? MOPBOYZ

@MOPBOYZ

2 ай бұрын

yessir !

Radiator small!! but nice project, try to review the rollers too

How much oil you running in a full tank

power

Hell yea🤘🏽🤘🏽🤘🏽

What is your gearbox?

The f12 is even more awesome than before! I wish my Scooter could do atleast 50-60mph. But i don’t think that there are that Many good tuning parts for a Speedfight 2, it’s a french scooter from Peugeot. Does about 43mph on gps without the variator restriction if i’m riding downhill for quite a bit. Can do 34 on gps maybe more on the straights. But it’s broken at the moment, the thread on the crank and the axle Hilding the clutch Bell is gone. I torqued the nuts for the clutch Bell and the belt disc WAY too much with an impact wrench that has WAY too much torque. 800watts and has 331.9 ft-lbs of torque. And a new crank costs 1499SEK which is about 142USD. Expensive stuff.

@ynk1011

2 ай бұрын

There are parts for the sf2

@ZebbePlayz

2 ай бұрын

@@ynk1011 yeah there are but not many very good parts. I have an air cooled sf2 and the website i order from doesent have many good parts. The best cylinder is a 70cc sport and it’s expensive af in my opinion. I live in Sweden so i don’t know if there are more good parts for it in the U.S or some other country.

Did you leave the 3-3.5s and the 3-5.5s with the soft contra?

@MOPBOYZ

2 ай бұрын

i ended up at all 3.5g with soft contra. i’m going to order more rollers and i think the sweet spot will be 3 3.5g and 3 4.5g

From my experiences you don’t wanna warm it up not using the water pump, the point of warming it up is warming it up slow so otherwise it wouldn’t be necessary at all

Nice build Do you ever do a price breakdown. And i personally don't don't like S6 pipes i find the build for the money it's not worth it. What's your thoughts on Leo Vince pipes. Cheers brother

@theowarmelink7347

Ай бұрын

I agree with you about the stage 6 exhaust. In Europe, I think they are overpriced. Pretty good performance but low quality. Thin metal and being unlacquered is not what competitors supply. In my oppinion nothing beats the Yasuni/Bidalot exhaust range. In this case a C20 would be perfect. Malossi team ('04 -'06 or 2) also, but they're more expensive. A Hebo Manston, Metrakit Pro race (2 and up) , TJT F1, or Kundo F1 are i.m.o. better exhaust for the money. Leovince (for so far I know) doesn't mak e exhaust in this rpm-range. Also not the best quality for the money. Not bad, not great. My pick for a low/middle revving 50cc or low revving 70cc would be: Tecnigas "TREK" (not the "next"), Laser Xpro, Yasuni R/Bidalot s2 or s3R, or Gianelli Shot.

@2WheeledMafia

Ай бұрын

@@theowarmelink7347 Yep I agree with you about the Leo vince I have a Derbi Atlantis 50cc AC with the piaggio engine and I notice the rpm range likes to flatline right around 92 KPH AT 9400RPM on flat ground and I know I can get a few more kph and Rpms out of her.

She sounds like a ripper!!!

Hoch mit das Rad 👍👍👍👍

💯

With rear brake the cable could be stretched? If it is you’ll never get a positive brake feel. Btw the bike is sick!!! Nice work!

@MOPBOYZ

2 ай бұрын

has brand new cable , pads & spring

@millymoo6575

2 ай бұрын

@@MOPBOYZ genuine cable or cheap copy

Kerja bagus kawan 👍👍

What kind of LED’s are you using I need those😂