I Axle Swapped to the Chrysler 8-3/4 - Part 3, Installation

Автокөліктер мен көлік құралдары

If you would like to support my channel and the Mopar community at large by buying a Jonny Mopar shirt click the link below.
jonny-mopar-merch.myshopify.com/

Пікірлер: 28

  • @Coelacanth97
    @Coelacanth973 ай бұрын

    Just discovered your channel and found many of your videos helpful and informative! I have a '70 Charger 500, bought it when I was 18 in 1986...it's at a body shop getting body & paint done, but I'll have a lot of work to do when it's finished. Your videos will really help me out. Thanks!

  • @JonnyMopar

    @JonnyMopar

    3 ай бұрын

    Thanks man. I greatly appreciate the positive comment.

  • @JustMoparJoe
    @JustMoparJoe4 ай бұрын

    A fine rearend indeed Jonny!

  • @JonnyMopar

    @JonnyMopar

    4 ай бұрын

    Thank you Joe

  • @Captaincurtsgarage
    @Captaincurtsgarage2 ай бұрын

    Thank you so much for making these videos Johnny I'm putting together an 8 3/4 from just a bare housing. This will definitely help

  • @JonnyMopar

    @JonnyMopar

    2 ай бұрын

    You’re very welcome. Good luck on the rebuild, you got this.

  • @Captaincurtsgarage
    @Captaincurtsgarage2 ай бұрын

    Love the videos Johnny . love the videos with your son.

  • @JonnyMopar

    @JonnyMopar

    2 ай бұрын

    Thanks buddy. Greatly appreciate the comment and thanks for watching.

  • @javimacias1215
    @javimacias12154 ай бұрын

    Very nice and detailed assembly, Jonny! Keep up the good work.

  • @JonnyMopar

    @JonnyMopar

    4 ай бұрын

    Thanks Javi.

  • @rikubot
    @rikubot4 ай бұрын

    Love your videos. I like the way you explain things and film. Also very relevant to me as I’m building a ‘69 charger with a lot of the same parts 🫡

  • @JonnyMopar

    @JonnyMopar

    4 ай бұрын

    Thank you rikubot. Yep, pretty much the same parts just a different skin.

  • @RandallSoong-pp7ih
    @RandallSoong-pp7ih4 ай бұрын

    Thanks for the tips and install and part numbers!

  • @JonnyMopar

    @JonnyMopar

    4 ай бұрын

    You’re welcome Randall. Thanks for watching.

  • @Greg383BB
    @Greg383BBАй бұрын

    Great video, I will use it too rebuild my rear end

  • @JonnyMopar

    @JonnyMopar

    Ай бұрын

    Thanks Greg.

  • @davidstarsky6435
    @davidstarsky6435Ай бұрын

    Great video

  • @JonnyMopar

    @JonnyMopar

    Ай бұрын

    Thanks David.

  • @1968charger
    @1968charger4 ай бұрын

    Another great informative video!!! THANKS

  • @JonnyMopar

    @JonnyMopar

    4 ай бұрын

    Thanks man. I Greatly appreciate that.

  • @maximuswedgie5149
    @maximuswedgie51494 ай бұрын

    Awesome video Johnny

  • @JonnyMopar

    @JonnyMopar

    4 ай бұрын

    Thanks Maximus.

  • @moparnut6286
    @moparnut62864 ай бұрын

    Furnace tube brush makes a great tool to clean out axle tubes not that expensive either.... Nice 8 3/4.

  • @JonnyMopar

    @JonnyMopar

    4 ай бұрын

    Great tip MoparNut. Thanks. I have to get one.

  • @TheProchargedmopar
    @TheProchargedmopar4 ай бұрын

    👍💪

  • @cartersmopargarage440
    @cartersmopargarage4402 ай бұрын

    Does the inner axles seals need to go all the way in to the little raised ledge of the housing?

  • @JonnyMopar

    @JonnyMopar

    2 ай бұрын

    That’s how far I pressed mine in. There’s probably some allowance as long as the bearing sleeve doesn’t hit it when you put the axle in.

  • @wht240sxka
    @wht240sxka4 ай бұрын

    Music 👎🏻👎🏻

Келесі