I absolutely love this video! Your work is amazing. Thank you for not talking down to people who are still learning and for sharing the "oops moments" as we all have them. Your tips and tricks, even the small ones are helpful and welcome. You have a new subscriber in me!

@FortressFineWoodworks

Жыл бұрын

Thank you for the sub! I'm glad you enjoyed it!

Great build video

@FortressFineWoodworks

Жыл бұрын

Thank you! Glad you enjoyed it!

Just amazing. Can't wait for part 2!

@FortressFineWoodworks

Жыл бұрын

Thanks again! And as always, thanks for spending your time watching!

I am always amazed at what you can do. You are a seriously talented dude! Keep it up, love watching your videos!!!

@FortressFineWoodworks

10 ай бұрын

So glad you are enjoying them. Stay on the lookout for my newest video this Saturday!

Nice build, enjoyed it. Tip - use a router sled with clamps for end grain cuts on router

@FortressFineWoodworks

Жыл бұрын

I've been wanting to make one of those. Great tip! Thanks!

Great video. I know the YT algo forces the 20min-ish bits, but to be honest I'd sit through an hour of your content, no question. Good to see a woodworker NOT slather glue, seriously. I also follow your general rules, because huge rivulets of glue is wasted $$ and time in clean up. Also agree that any kind of router is scary -- ask my left middle finger if he agrees. Question 1: I'm hesitant to use wet cloth to get squeeze out based on the idea that I'll wind up just creating a thinner form of glue that goes deeper into the grain... thoughts? Question 2: Was that a part 2 spoiler where you have to plug your wrong-side Euro hinge holes? LOL.

@FortressFineWoodworks

Жыл бұрын

Haha I appreciate it for real. It's more so the amount of work that I would have to put into one video. A 45 minute video is a ton of editing. So I'd rather get 2 videos from it. 1. The wet microfiber is so extremely good at cleaning the grain, it will surprise you. Give it a try. 2. Thankfully I paid very close attention and indeed...... drilled them on the...... correct side.

EXCELENTES TRABAJOS . GRACIAS POR OFRECERNOS TUS VIDEOS

@FortressFineWoodworks

5 ай бұрын

Of course! Thank you for watching

You need to get one of those sliding overhead cranes! 🤔

@FortressFineWoodworks

6 ай бұрын

Very true, that would be really nice! Thanks for watching!

Hello , Very good I'm from Indonesia

@FortressFineWoodworks

Жыл бұрын

I appreciate it!

Another amazing build!

@FortressFineWoodworks

Жыл бұрын

Thank you.

At 11:43 - this mishap could have been prevented by having your backer board laying on its face instead of on edge. It happened because the backer board lost contact with the fence. A coping sled would also have prevented the issue. Workshop Companion has one or two devices which make moving sheet goods alone easier.

@FortressFineWoodworks

9 ай бұрын

So true. Then it would've been too wide to get shot into the blade. I definitely need to make a jig for the router table

Surprised you don’t have a shaper with a power feeder!

@FortressFineWoodworks

7 ай бұрын

The time will come. I wasn't intending to do a lot of cabinetry but that's what people want right now. Thanks!

Great project man! What is the router brand and HP your running in that router table?

@FortressFineWoodworks

Жыл бұрын

Thanks! I put the router in the description. It's labeled - Bosch Router (for router table) - amzn.to/3VDxROU

first of all amazing project not realy my style but i still think that is F impressive to build smth like that but honestly i have a question a few years back i made a epoxy table with my dad for my dad and im only now realy finishing it but i have that problem that when i sand the epoxy with my random orbital sander that you can see the seams where the sander overlaps if you know what i mean is there a way to prvent that other than hand sanding?

@Slice-Darryl

Жыл бұрын

and another thing is in your video is so much information all those deatial i mean if you realy want to get every out of it you have to watch it multiple times i dont even know if i have seen a video of an project with that much detail thank you for that

@FortressFineWoodworks

Жыл бұрын

You might be going too slow with your orbital. Criss cross your motions, so go across the width of the board with the sander, and end with strokes going with the grain. This will even the sanding.

@FortressFineWoodworks

Жыл бұрын

I'm glad you are getting so much out of them.

@Slice-Darryl

Жыл бұрын

@@FortressFineWoodworks well thats smth i have never heard going too slow with the sander normally its the opposite :D but i will try it tomorrow thanks for the advise

@FortressFineWoodworks

Жыл бұрын

Yeah I don't follow the 1 inch per second rule. I go about 3 to 4 inches per second

💥💥💥👍😎

@FortressFineWoodworks

5 ай бұрын

Thanks for watching!