Great to hear that it's still working out for you! Little updates like this are always enjoyable to revisit, thanks :)

MackieBass in the house!

Thank you for this honest review 👍 I’m waiting for mine to arrive.

@MackieBass

4 ай бұрын

Glad it was helpful!

exciting! I just received mine and your video are great! Thanks for posting very helful!

@MackieBass

2 жыл бұрын

Glad to help!

Cracking little compressor when I need another I would certainly be lookin at this one cheers .: )

Hi good review. I bought the same compressor and agree with everything you say. The bleed screw under the tank is a bit of a pain so I will look to change it in the future for a similar wing nut type. Also when my compressor turned up at the door after unboxing it I noticed the elbow joint that goes into the cylinder head was snapped off and the thread part was stuck inside the head so I contacted the company I bought it from and they sent me a replacement cylinder head with the new elbow joint attached. What I did was go to screwfilx and bought some liquid ptfe they sell two types, a normal liquid seal and a thread lock liquid ptfe that's made for vibrating parts I bought that one and I've had no problems with leaks. In fact I've put it on everything regulators spray gun connections and got rid of all the ptfe tape. I'd definitely recommend it. 👌

@ade63dug

Жыл бұрын

I use cimberio liquid and i find it great .

Fantastic review!

@MackieBass

3 ай бұрын

Glad that you think so!

Great Video 👏🤘

Bloody awesome video my friend 🤘👊

@MackieBass

Жыл бұрын

Glad you enjoyed it

Wow..that's amazing

@MackieBass

2 жыл бұрын

Thanks a lot 😊

My 80 gallon is minimum for a full paint job. The issue is solved by replacing the compressor to tank line with a coil of brake line with a fan on it. Basically, the moisture condensates on the walls and drips to the drain... Well when its hot it just becomes humidity until the tank cools down again.... The coil will get you better results on any compressor, at least get you farther b4 your contaminated, them filters work, temporally, so it might save your ass at the end of a job if a couple minutes will make or brake you but they only do so much ......

@TEN-TIMES-HARDER

2 жыл бұрын

PS USA dudes, the rest of the world runs 220. We run 110 because Edison and Westinghouse knew that their is a lot more wasted electricity going through the meeter running 110.....

I’ve just bought one of these for working with chocolate actually! We use spray guns to spray coloured cocoa butter into moulds. I spray several at a time so I needed a bigger compressor. I also use a HVLP gun to spray with - this is my first time setting everything up with the compressor - I hope it all goes well I don’t know so much about it!!

@MackieBass

2 жыл бұрын

Cool as man! Would love to see it!

@chloeoswald663

2 жыл бұрын

@@MackieBass I tried it for the first time last night! It’s perfect! I get a bit of backspray though.

@MackieBass

2 жыл бұрын

I bet your backspray is tastier that mine!

@skrefurbishedinteriors

2 жыл бұрын

@@chloeoswald663 how is the compressor working out for you? And what gun did you buy for it please?

Hi My brother I have this compressor but the ones motor is in the working Time it's hot then after not are having in atanker so what is the problem off this machine

Great video. So it runs for 25 secs. What is the CFM of your spray gun? More importantly if the compressor kicks in can you still use the spray gun while compressor is running ? Thanks

@MackieBass

Жыл бұрын

Around 20psi, and yes I can still use it, not sure how long. It's not designed for big projects

Add an extra tank. Made from a lpg tank. Small PC fans on the compressor heads.

@MackieBass

Жыл бұрын

Not a bad shout!

I'm looking for some help with the same compressor. When set at 4 bar and using my spray gun, the pressure drops to zero, until I release the trigger, then it returns to the set pressure, so I initially have enough pressure, they the spray tails off to barely anything. It seems to work fine otherwise. I switched over to my backup compressor for comparison, and when I pull the trigger the pressure on it drops around 1 bar at the most. Any help appreciated.

@MackieBass

Жыл бұрын

What do you means set at 4 bar? The compressor or the Gun?

Nice work😎how's your Hyundai working 2 years later ? Still going strong? Looking for around 50L compressor to run a LVLP gun for spraying guitars like yourself - which model/spec guns do you use for spraying guitars? Cheers!👍🏽

@MackieBass

4 ай бұрын

Thanks. It is still going strong. I use just regular LVHP guns, nothing special and they work fine

What size compressor should I get for painting tank and fenders for Harley. This includes airbrush. Some are saying I need to get dual stage pump

@MackieBass

6 ай бұрын

This one does all the above without any issues. I am happy with it.

@Soloriderpowder

6 ай бұрын

@@MackieBass This is the one you have to release the air every single time you use it right

what coupling and hose pipe you recommend ?

@MackieBass

8 ай бұрын

I just use a think one 5m long. Standard, nothing fancy.

Zajebiste piwko ;D A kompresor kupił byś drugi raz ten sam ?

@MackieBass

Жыл бұрын

Dzieki, i pewnie tak. Do tej pory mnie nie zawiodl. Wiadomo ze wolalbym wiekszy, ale do malego garazu jest ok!

Hi, I have got questions. Do you recommend if I should use 24L or 50L hyundai air compressor to respray on car using LVHP spray gun? Does it work well for you if you have used 24L or 50L to respray on your car? I'd love to know!

@MackieBass

Жыл бұрын

For the car get the 50L, bigger is better!

Oil free compressors have a built-in life span, typically around 200 hours running time before the teflon wears out. If you can buy replacement cylinders/liners your good, if not you need a new compressor. Your bambi compressor will outlive the hyundai by a few decades at least :)

@MackieBass

Жыл бұрын

Fair enough point. Bambi is fantastic

@ade63dug

Жыл бұрын

This is simply not true with this machine . piston seals cylinders and the reed valves are cheap . all parts are available easily from the aftersales guys . they are considered service items . the biggest killer for all compressors is over using the duty cycle and poor servicing . I have been using mine for 3 years and done one proper service when I saw a drop in performance . everything was fine apart from dirty air filters .

@JohnGuest45

Жыл бұрын

@@ade63dug As said, the tefllon wears out but if replacement parts are available then its all good. The hyundai is too noisy for my application even though its called silent its not as silent as a bambi. I couldnt fire up a hyundai at 3am in the house and live to tell the tale :)

@marty3553

Жыл бұрын

The cost of a bambi is far more money I don’t have So I will be getting one of these Hyundai compressors

Siema pozdrawiam, chyba też sobie taki sprawie.

@MackieBass

2 жыл бұрын

Swietna sprawa. Moze nie ma mocy tyle co paskowy, ale daje rade!

🍻

What is the cfm rating at 90psi

@MackieBass

6 ай бұрын

No idea, sorry.

Why don't they make a 100 or 150 litre version

@MackieBass

Жыл бұрын

It's a good question, I'm sure there is a valid reason for this, like engine capacity to handle such a load? I don't know.

May I know howmuch in Indian rupees?sir!

@MackieBass

Жыл бұрын

No clue!:?

Could you please say how much less electricity Petrol air compressor consumes as apposed to same power and capacity fully Electrical compressor ? 10 Times less ? 2 times less ? Thanks

@MackieBass

Жыл бұрын

I have no idea if I'm honest...