No video
Hyper Flash Turn Signal Repair - 6th Gen Camaro Non RS Models
Fixed the hyper flash caused by LED tails lights by replacing the resistor in the Gen5 DIY harness. This can be applied by splicing also but definitely recommend getting the hardness as it is much easier. Link below for 6th Gen Models. (This will not work for aftermarket taillights)
Plug n Play Harness:
www.gen5diy.co...
Replacement Resistors:
www.amazon.com...
Пікірлер: 37
Thanks for sharing!
@RCCamaro
2 жыл бұрын
Thanks for watching! Always here to help 😁
Do you need to buy the resistor? Or is it optional
@RCCamaro
2 ай бұрын
If you but the harness from Gen5 DIY, it will come with them. But if you plan to splice into the factory lines, you will need to buy them. They are pretty cheap to buy and come with splice adapters
Hey good video. I have a 2016 v6 camaro and my aftermarket vland taillights hyperflash. I was going to buy a harness like you have listed, but why will it not work for aftermarket tailights? Does that mean I have to manually wire resistors into my factory harness? and do you have a wiring diagram?
@RCCamaro
Ай бұрын
Thanks for watching! I am not too sure if the harness will work or not but my thinking is that they have it sired different or is wired for RS cars but I do not have wiring diagram unfortunately I had to do a lot of testing
@AliMoses-no8on
Ай бұрын
@@RCCamaro Okay! Thank you for the quick response!
@RCCamaro
Ай бұрын
@@AliMoses-no8on my pleasure! Anytime!
Does the 2014 ss have this as well mine been hyper flashing was just one blinker but now 2 blinkers
@RCCamaro
7 ай бұрын
It's completely possible to have this for the 5th gens. If you upgraded your headlights, taillights, or upgraded to LED than you will need resistors in line as well. This can be as simple as getting the harness (if they make one) or adding a resistor.
@DEADPOLES
7 ай бұрын
@RCCamaro yes I do there morimoto color changing with halos drls went out then blinker issues not sure if I should just bring it in or figure it out myself. Lol 😎👍
@RCCamaro
7 ай бұрын
its probably that. Most aftermarket headlight housing's have built in resistors or ballasts. I would say if you were to get new ones or fix the DRLS that went out it would fix it. its pretty much signaling that there is something wrong with the circuit.
@DEADPOLES
7 ай бұрын
@RCCamaro hey that's a good point! Maybe that's where the problem is I haven't tested the drls thought they ran with the blinker. But not sure. Lol
@RCCamaro
7 ай бұрын
@DEADPOLES haha it's possible they are tied in together (wouldn't be surprised if they do). But if that doesn't fix it then it's probably needs a resistor. They do fail after some time.
So if u buy vland headlights they are not plug and play I got a 2.0 2016 and they don’t have the led lights they have halogen and j want the ones that look like an eyebrow with drl
@RCCamaro
3 ай бұрын
Im assuming your talking about the 19+ head lights?
@cactusjavk
3 ай бұрын
@@RCCamarono the ones like yours
@RCCamaro
3 ай бұрын
@cactusjavk ohhhh they are the 4 light ones right? Yea I had to buy mine from a junk yard in Florida haha but these are getting super rare to find for some odd reason
@cactusjavk
3 ай бұрын
@@RCCamaro I’ve found a company that sells them vland but I think I have to buy a harness since mine is a non rs
@RCCamaro
3 ай бұрын
@cactusjavk ah gotcha, I'm surprised they don't have one built in. But maybe Gen5 DIY may have one
Thanks for uploading. Dealing with the same issue. Harness company says harness only compatible with OEM assembly swap. Are your led tail lights oem?
@RCCamaro
Жыл бұрын
My lights are oem. The harness from gen 5 diy will work. I think they mean if you try and use the aftermarket tail lights and head lights.
@efborgomini4604
Жыл бұрын
Quick question- did you just connect the single resistor harness to one side? I know the dual resistor is for adding led reverse bulbs. Want to make sure I’m installing correctly. Thanks again!
@RCCamaro
Жыл бұрын
@@efborgomini4604 you have to put it on both sides
@efborgomini4604
Жыл бұрын
So did you buy two sets or remove one resistor from the other harness?
@RCCamaro
Жыл бұрын
@EF Borgomini I bought two. One for each light.
Disculpa y como saber si el harness no sirve
@RCCamaro
Жыл бұрын
la única forma de saberlo es poner la resistencia en línea y verificar. también verifique la resistencia para asegurarse de que no se haya quemado
@damiansalazar4969
Жыл бұрын
Si Por q tmb me hace cuando pongo la direcional alos tres segundo enpiesa a flashar rapido
@RCCamaro
Жыл бұрын
@@damiansalazar4969 revisa tus luces. podría ser una bombilla fundida o si actualizó a las luces traseras LED RS, entonces necesitará el arnés para detener el parpadeo rápido.
@damiansalazar4969
Жыл бұрын
@@RCCamaro gracias
Whats the name or id for this item ?
@RCCamaro
Жыл бұрын
I should have highlighted it in the video or be in the description. If not let me know and I can look it up
@brianm1997
Жыл бұрын
@@RCCamaro appreciate my men ,,,, my model is Camaro Lt 2.0 turbo
@RCCamaro
Жыл бұрын
@brianm1997 should still work but please keep in mind that most of my videos are for the v6 so everything not dealing with the engine should apply to your car also.