Step-by-step instructions on how to properly disassemble, drill, tap, and reassemble a Toyota IFS steering gear box for hydro assist.
Жүктеу.....
Пікірлер: 57
@ryanstewart15213 ай бұрын
Sweet vid, every little step explained clearly. Watched it a couple times and feel ready to tap that box!
@jerryfie54755 ай бұрын
Awesome video, I have used it several times now to really rebuild and tap boxes for my friends. Everybody likes the relocation of the second tapped hole.👍🏻😎.
@patrickgipson70605 жыл бұрын
Outstanding tutorial, I ten years of Toyota building I have never been as mad as when I accidentally let the ball bearings fall out. It is possible to recover from but not easily.
@timwoods93506 жыл бұрын
this is the best hydro assist tutorial I've seen so far! Cheers!!
@VonWilsonator11 жыл бұрын
Thankyou for the views! Glad to hear the video is helping. Im a helicopter mech by trade, 4x4 fabrication is just a hobby.
@theotherguy3083 Жыл бұрын
The best tutorial I have seen so far
@ericgalloway4614 жыл бұрын
Great video, thanks for the excellent guide!
@driftersbeachcafe59613 жыл бұрын
Thank you for a great video and detailed comments
@asurwyatt Жыл бұрын
Hey thank you so much for all your helpful hints my Hydro assist is wonderful
@PhilipGragg7 жыл бұрын
Great job, very descriptive video!
@seano27362 жыл бұрын
well done sir. great video, and very descriptive. thank you.
@high_desert_crawlers11 жыл бұрын
Awesome video!!! Thanks a lot!!!
@FilterYT3 жыл бұрын
That was great, thanks for sharing!
@lordaleksandre5 жыл бұрын
What a great video!
@Cjdavis002 Жыл бұрын
awesome tutorial. Thank you
@Arkansasdisc10 жыл бұрын
Thanks for the video!
@t_buzz94104 жыл бұрын
Thanks so much for this video!!
@rokntoy11 жыл бұрын
Didnt notice the first time I watched but its ironic when your doing your reassembly the alice in chains is playing and right as you were puting part in and watching the teflon ring it said " Oh god please could you help me make it threw". Lmao!!
@Jits_Monster11 жыл бұрын
Thank you.
@Braun4x4BC6 жыл бұрын
GOOD VID!
@ericwilson686510 жыл бұрын
Yup. Top port goes to the right side of the ram and forces your wheels left. Fwd or outboard port goes to the left side of the ram forcing your wheels right. As mounted,aft inboard port is return, and fwd outboard is pressure.
@VonWilsonator11 жыл бұрын
Napa reseal kit # 7-3711 Gear. Probably should have mentioned that in the video. My apologies.
@anyandalldiy67044 жыл бұрын
Thank you for this video. It was perfectly straight forward and to the point. I had no problem tapping my box thanks to you. What pump dis you run with this setup. Ive had the stock pump for about a year and it's just not cutting it. Also can you do a toyota hydro assist system bleeding video? Thanks.
@Excel4wd11 жыл бұрын
Great vid bro, took all the guess work out of my rebuild. Who you work for? Thanks, I owe you a cold one for this vid broths.
@The200620012 жыл бұрын
Good show i'm about to do this in a week, you seem like you know whats up. So this vid came out at the right time for me. Whats eye pro something I need ?
@VonWilsonator12 жыл бұрын
Haha no. Those other 2 posts are from guys i work with. :"Eye Pro" is short for Eye Protection. Safety is a big deal at work and a bit over exagerated. They're joking, saying i should wear safety glasses. So no you dont need it unless you really really want it. Glad this vid helps. good luck with your setup!
@jefftrinchera44752 жыл бұрын
Question when you say pushing the tires left is that from in the truck or in front of the truck please clarify with passenger and driver thank you great video by the way did my box you walked me through it
@NordicDan3 жыл бұрын
For a hydraulic application like this, would you prefer to use teflon tape on the threads or thread sealing compound? My first thought would've been thread sealer. Just wondering if you actually prefer the tape as opposed to the sealer or if it doesn't really matter for this.
@nswsparky10 жыл бұрын
so the top port is pressure when turning left. I am getting the hoses figured out for my assist.
@jefftrinchera44753 жыл бұрын
Can you move the left pressure line further around the barrel of the gear box towards the back of the truck due to moving the box forward?
@kevinpisani67869 жыл бұрын
Hi i hope you can help me :) i went through your instructions. problem is when i try to pull out the input shaft it get stuck! any suggestion?
@muddyudders10 жыл бұрын
where do you buy your ram and hoses/ fittings?
@Arkansasdisc10 жыл бұрын
I drilled and tapped my box per this video. Seems to have worked well. I plugged the holes, put the box back in and bled it. Then, a week later I went wheeling and half-way through the day the box puked out all the fluid between the mating surface of the input shaft and the steering box housing. I don't know if the Permatex just didn't hold, or if something internally went wrong and built enough pressure in that area to force the fluid out. Any ideas? I am heading out to the shop in a minute to tear into it. Thanks!
@Arkansasdisc
10 жыл бұрын
Tore apart. Only thing that seemed incorrect was I had squishes permatex all over the new O-ring I had installed. Carefully scraped it off and re-installed ring. Box going back together now...if only I could find the torque specs for the 8 bolts...
@kalindanley28432 жыл бұрын
A link to the drill bit and tap on Amazon or someplace would do ya good. And anything else you might want to link
@memorycdrew10 жыл бұрын
Kickass detail man, good work, seems like you know 'Yota vehicles, know anything about Delphi boxes?...jk
@thomashightower39692 жыл бұрын
You know you can reinstall the 42 ball bearings it is just like a ball screw, I had my son do mine
@Jits_Monster11 жыл бұрын
What's the part# on the napa reseal kit?
@wilstillens78363 жыл бұрын
Hi are you still making these? I am a land cruiser owner. Can you do this to an 80series land cruiser?
@user-tu9fp9wo3i4 жыл бұрын
How many pomegranates wear inside the can
@sleeks99394 жыл бұрын
Once you center the sector shaft. After that step do you have to place the worm shaft in neutral position?
@VonWilsonator
4 жыл бұрын
Sleek S center the input shaft, by eye. You should look down from the top, and see that the sector shaft gears will mesh up evenly.
@sleeks9939
4 жыл бұрын
@@VonWilsonator okay, thank you very much truly appreciated it.
@dillondvorovy46313 жыл бұрын
How much for one of your gear boxes?
@dillondvorovy46312 жыл бұрын
How much for a tapped gearbox?
@oceanhouse80804 жыл бұрын
You can get it back together its just time consuming
@cerberii6 жыл бұрын
i think you've done this before
@shawnmorgan20528 жыл бұрын
how do i get one of these???
@ericwilson6865
8 жыл бұрын
Good question. Any 4x4 '86-'95 Toyota pickup or 4Runner will have this box in them.
@ericwilson686510 жыл бұрын
Thnx! I know they're in a few of the later model half ton chevys, and they're nearly identical to Borgeson Boxes found in dodges. All I know about D+Ting them I learned here: www.pirate4x4.com/forum/dodge/944064-tapping-borgeson-box-etc.html
@hunglow22002 жыл бұрын
Turn the back ground music off next time. It sounds terrible and i like every song that was played. Other wise its a good video
@jeffgood64412 жыл бұрын
4 and a quarter why not just 5 turns there boss
@whatyoumakeofit66355 жыл бұрын
What is the reason for doing this ?
@javier7high
5 жыл бұрын
Better handling
@jeffgood64412 жыл бұрын
5 turns and 2 1/8 back is center boys dont let this man mind fuck you lol just kidding bro this helps me a lot
@MrCstone19 жыл бұрын
I think I sent you a message on facebook...can you check and get back to me?
Пікірлер: 57
Sweet vid, every little step explained clearly. Watched it a couple times and feel ready to tap that box!
Awesome video, I have used it several times now to really rebuild and tap boxes for my friends. Everybody likes the relocation of the second tapped hole.👍🏻😎.
Outstanding tutorial, I ten years of Toyota building I have never been as mad as when I accidentally let the ball bearings fall out. It is possible to recover from but not easily.
this is the best hydro assist tutorial I've seen so far! Cheers!!
Thankyou for the views! Glad to hear the video is helping. Im a helicopter mech by trade, 4x4 fabrication is just a hobby.
The best tutorial I have seen so far
Great video, thanks for the excellent guide!
Thank you for a great video and detailed comments
Hey thank you so much for all your helpful hints my Hydro assist is wonderful
Great job, very descriptive video!
well done sir. great video, and very descriptive. thank you.
Awesome video!!! Thanks a lot!!!
That was great, thanks for sharing!
What a great video!
awesome tutorial. Thank you
Thanks for the video!
Thanks so much for this video!!
Didnt notice the first time I watched but its ironic when your doing your reassembly the alice in chains is playing and right as you were puting part in and watching the teflon ring it said " Oh god please could you help me make it threw". Lmao!!
Thank you.
GOOD VID!
Yup. Top port goes to the right side of the ram and forces your wheels left. Fwd or outboard port goes to the left side of the ram forcing your wheels right. As mounted,aft inboard port is return, and fwd outboard is pressure.
Napa reseal kit # 7-3711 Gear. Probably should have mentioned that in the video. My apologies.
Thank you for this video. It was perfectly straight forward and to the point. I had no problem tapping my box thanks to you. What pump dis you run with this setup. Ive had the stock pump for about a year and it's just not cutting it. Also can you do a toyota hydro assist system bleeding video? Thanks.
Great vid bro, took all the guess work out of my rebuild. Who you work for? Thanks, I owe you a cold one for this vid broths.
Good show i'm about to do this in a week, you seem like you know whats up. So this vid came out at the right time for me. Whats eye pro something I need ?
Haha no. Those other 2 posts are from guys i work with. :"Eye Pro" is short for Eye Protection. Safety is a big deal at work and a bit over exagerated. They're joking, saying i should wear safety glasses. So no you dont need it unless you really really want it. Glad this vid helps. good luck with your setup!
Question when you say pushing the tires left is that from in the truck or in front of the truck please clarify with passenger and driver thank you great video by the way did my box you walked me through it
For a hydraulic application like this, would you prefer to use teflon tape on the threads or thread sealing compound? My first thought would've been thread sealer. Just wondering if you actually prefer the tape as opposed to the sealer or if it doesn't really matter for this.
so the top port is pressure when turning left. I am getting the hoses figured out for my assist.
Can you move the left pressure line further around the barrel of the gear box towards the back of the truck due to moving the box forward?
Hi i hope you can help me :) i went through your instructions. problem is when i try to pull out the input shaft it get stuck! any suggestion?
where do you buy your ram and hoses/ fittings?
I drilled and tapped my box per this video. Seems to have worked well. I plugged the holes, put the box back in and bled it. Then, a week later I went wheeling and half-way through the day the box puked out all the fluid between the mating surface of the input shaft and the steering box housing. I don't know if the Permatex just didn't hold, or if something internally went wrong and built enough pressure in that area to force the fluid out. Any ideas? I am heading out to the shop in a minute to tear into it. Thanks!
@Arkansasdisc
10 жыл бұрын
Tore apart. Only thing that seemed incorrect was I had squishes permatex all over the new O-ring I had installed. Carefully scraped it off and re-installed ring. Box going back together now...if only I could find the torque specs for the 8 bolts...
A link to the drill bit and tap on Amazon or someplace would do ya good. And anything else you might want to link
Kickass detail man, good work, seems like you know 'Yota vehicles, know anything about Delphi boxes?...jk
You know you can reinstall the 42 ball bearings it is just like a ball screw, I had my son do mine
What's the part# on the napa reseal kit?
Hi are you still making these? I am a land cruiser owner. Can you do this to an 80series land cruiser?
How many pomegranates wear inside the can
Once you center the sector shaft. After that step do you have to place the worm shaft in neutral position?
@VonWilsonator
4 жыл бұрын
Sleek S center the input shaft, by eye. You should look down from the top, and see that the sector shaft gears will mesh up evenly.
@sleeks9939
4 жыл бұрын
@@VonWilsonator okay, thank you very much truly appreciated it.
How much for one of your gear boxes?
How much for a tapped gearbox?
You can get it back together its just time consuming
i think you've done this before
how do i get one of these???
@ericwilson6865
8 жыл бұрын
Good question. Any 4x4 '86-'95 Toyota pickup or 4Runner will have this box in them.
Thnx! I know they're in a few of the later model half ton chevys, and they're nearly identical to Borgeson Boxes found in dodges. All I know about D+Ting them I learned here: www.pirate4x4.com/forum/dodge/944064-tapping-borgeson-box-etc.html
Turn the back ground music off next time. It sounds terrible and i like every song that was played. Other wise its a good video
4 and a quarter why not just 5 turns there boss
What is the reason for doing this ?
@javier7high
5 жыл бұрын
Better handling
5 turns and 2 1/8 back is center boys dont let this man mind fuck you lol just kidding bro this helps me a lot
I think I sent you a message on facebook...can you check and get back to me?
Surpluscenter.com