Gas tank was removed as it was being replaced, you dont need to do it for a belt change.

@jasonwatson8375

2 жыл бұрын

What did you use for a fuel tank

Great vid man!

@hanksgarage_

6 жыл бұрын

Tristan Heckler thanks bud

Nice video; it helped, thanks... Couple pointers for anyone else doing a similar job (mine is a Husqvarna YTH1342): 1) it looks like you are missing a "belt keeper" that bolts on under (against unibody) the idler pulley. Part #532 17 55-56 on my schematic. 2) pause the video at 5m25s to see the proper routing. V is around the transmission pulley, straight run through the belt keeper to the engine pulley (still V side), then directly around the clutch pulley (still v side), then directly to the idler pulley (flat side of belt), and back to the transmission pulley 3) like you I removed the PTO clutch, but now that I've played around I believe the belt should be removable by simply keeping the clutch pedal depressed - hopefully somebody can confirm Thanks again! -ace

Hi Hank, is the engine pulley that's attached to the PTO clutch suppose to spin freely like the other pulleys or no?

Would you have an Idea what's going on with mine the clutch doesn't move as well as forward and backwards doesn't work its a Husqvarna YTH23V48

I have a Husqvarna YTH2448 Riding Mower that I would like to flip on its side in order to replace the steering bar because it is nearly impossible to remove the bolt & nut at the end closest to the steering column. Do I need to remove the gas and oil before setting it on its side? Will turning it onto its side hurt the inside of the engine in any way perhaps from oil getting into areas where they shouldn't? I'll remove the deck before flipping it.

Good Video buddy

@amberfhscott3885

6 жыл бұрын

KB'S Small engine Repair parts & Service 8

What do you think of Predator engines from Harbor Freight ? Good/Bad ?

@hanksgarage_

6 жыл бұрын

Gregg Erdner imo they are far better than the new Briggs are

Thank you very much for putting this video up. Big help. I have the same mower. BTW, should the tensioning wheel spin? Mine is stuck like glue.

@mikedunning424

3 жыл бұрын

Yes

Video seems much better 👍

@hanksgarage_

6 жыл бұрын

da coder really? I didn’t make any changes

nice work hank! I buy riding mower that need work and fix them up! Butt it like you said lawnmowers! You never know what your getting into sometimes!

@hanksgarage_

6 жыл бұрын

James Aydelott hey man yea lawn tractors can very quickly not be worth fixing. Thankfully this one was and its owner loves using it !

Be careful with that carb when you take it apart if it’s a Nikki, there is a very small brass jet that fell out on the first one I ever rebuilt. I didn’t realize it fell out and the engine ran fine until I engaged the blade. Had to go on KZread to find out what was missing, found the jet on the shop floor and she ran perfect after. This might be a good topic for a future video.

thanks dude

Great video man I did the same thing . flipped mine over and and changed out the drive belt ..the problem Is I need to change out one of the plastic pulleys and I cannot get it' off The bolt just spins ..suggestions would be helpful thanks again man. I have a 2004 huskavana YTH1542 It's the idle tension pulley

@hanksgarage_

3 жыл бұрын

Try and get something on the other end to hold the bolt in place, or try and use an impact and you may get lucky

@scraig000001

3 жыл бұрын

@@hanksgarage_ thanks man.. got it.👍👍

My yth2348 goes in reverse, but not forward. I figure it's a clutch problem but then again I dont really know much. What do you think it could be?

@garysnyder379

4 жыл бұрын

8

sounds like it needs the valves adjusted, that's why it hesitates before cranking

@hanksgarage_

5 жыл бұрын

Already been done in another video made after this one

Nice snake skin at 2:25

Ok Mr.Hank, ...... what's with the ''Ming The Merciless'' Beard look ? ..... Has Briggs not made a mini mower to trim that off ? :~)

@hanksgarage_

6 жыл бұрын

tommy hanlon haha I’ve had that forever man !

good product fast shipping

I put my drive belt on without taking the pto off I did first time but 2nd time nope I started at back of it put the belt through like it shoudl be and got to front and pry it a little bit with wrench and it went on no prob

Next time just put a plastic bag under the gas cap saves lulling the tank

@hanksgarage_

5 жыл бұрын

The tank was removed to be replaced. Not because it had fuel in it.