Huge Vise Restoration ["FIX" Huge Rusty Vise]
Ғылым және технология
In this video I restored a huge vise. During this restoration of the large antique vise, I had to grind, sandblast, weld, fill and a lot more to make this old rusty tool shine again.The special thing about this huge vise is that it has a quick adjustment, which means that you do not need to turn the lever for a long time to adjust it, but simply slide it quickly back and forth.
▬ What is being done?! ▬▬▬▬▬▬▬▬▬▬▬▬
First, I disassembled the huge vise and roughly washed it off. Since the cover that leads the shaft with thread broke off at the screw holes, I cut new corners from sheet metal with the angle grinder and welded them with an electrode welder. Of course, these weld seams then had to be sanded well and the holes drilled again. Drilling the holes was very difficult because the welding hardened the material extremely. I made a new screw on a lathe because a screw was no longer the original and had already been replaced by my previous owner. Afterwards, I also welded and sanded any unevenness on the vise jaws. I then masked off all mechanically stressed surfaces and prepared them for the sandblasting, which took place immediately afterwards. After sandblasting, I masked the areas that should not be painted with paint. Before I applied the primer, I filled in all the surfaces with a spatula and sanded them finely to get a smoother surface. In this project I also hot burnished some parts and cold burnished individual components. Now only the remaining parts had to be preserved with paint, then all moving parts had to be coated with grease or oil and then put everything back together again. And the big old vise shone with a new shine.
▬ Good to know ▬▬▬▬▬▬▬▬▬▬▬▬
I bought this huge vise on a classifieds website. In this article it was only stated that the vise is large, but on site I knew it was huge! He is 25,6 inch (650mm) long, 11,8 inch (300mm) wide, 11 inch (280mm) high and weighs 104 lbs (47,2 kg). Two of us even had to lift it into my car. I've always wanted a bigger vise because I only have a small one. You can also see him in my videos. It regularly reaches its limits. Buying a new one is too expensive for me. That's why I decided on a used one that still needs to be worked on a "bit". Definitely a bargain for the size!
I used the following tools: cordless screwdriver, welding machine, slag hammer, welding mask, wire brush, brush (for washing), adhesive tape, film to cover, knife, rust remover, orbital sander, file, various drills, various grinding attachments, sandpaper, toothpicks, primer, topcoat, paint spray
It took me about 32 hours without the paint drying time.
▬ Chapter ▬▬▬▬▬▬▬▬▬▬▬▬
0:00 look at gigantic large vise
1:41 Take apart
4:21 look at components
4:43 Wash all parts with soap and water
5:43 Weld and grind the back Cover and vise jaws
8:20 remove coarse dirt
8:40 am Masking the functional surfaces with adhesive tape for sandblasting
9:55 remove coarse dirt and mask for sandblasting 2nd part
10:34 Remove coarse dirt and tape back cover for sandblasting
10:46 Recut screws thread and prepare optically
11:16 adjust newly made screw
11:42 Recut thread sliding carriage
11:56 Punch, drill and screw on the cover with a special trick
12:28 Weld on new support (anvil) and grind
13:18 Grind the vise jaws
13:37 Sandblast, fetch and clean parts
13:55 Fit and adjust vise jaws
14:09 Preparation for the canning
14:35 Fill and sand the rough surface
15:57 Wash components with acetone
16:11 Spray large parts with primer
16:40 Brush on large parts of the top coat
17:38 Paint the lettering with white
18:21 Spray the side of the vise jaws black
18:28 Browning small parts with a burner and linseed oil
18:52 add quick browning to other small parts
19:25 Apply grease to all functional surfaces
19:34 look at all components
20:01 Assembling the vice
21:42 Look at the gigantic large vise finished and function test
▬ Do you like it?! ▬▬▬▬▬▬▬▬▬▬▬▬
Do you like the video? Then please like it, subscribe and share it!
Thank you so much!
Пікірлер: 145
I like the way the metal darkens instantly with rapid bluing, but I also feel that heating things with a torch is so much funnier! :D
@ForgottenShineRestoration
3 жыл бұрын
Hey Jevi. Thanks! Yes of course it's more fun, but I wanted to introduce both methods 😀
Genius way to restore a large vice. I absolutely loved your video. I bet it took a very long time to drill holes in a piece of metal so thick.
Wow! Excellent restoration! The video was beautifully shot and edited too. I always appreciate the stop motion animation as well. This vise and video are exemplary. Great job. I am looking forward to future projects. Take care 😃👍🏼
@ForgottenShineRestoration
3 жыл бұрын
Thank you for this wonderful comment!
Amazing work!! What patience to see it through but the end result is pure art. Better than when it left the factory. Makes me want to collect vices now hahaha
@ForgottenShineRestoration
3 жыл бұрын
Hello Mauricio Orantes. I'm happy if you liked it so much! I hope you have subscribed 😅
Good job mate.
The plate at the back needed fixing, but other than that, I’d love to see a vice restoration video that goes like “Look at this beauty. Bit of grease, good to go!”
@ForgottenShineRestoration
11 ай бұрын
😅🐢
That quick adjust function is pretty cool
@ForgottenShineRestoration
3 жыл бұрын
Yes, a very good relief for the span :)
Монументальность !
Impact driver for the screws.
Yes. New channel. Love the work. I wish you success.
@ForgottenShineRestoration
3 жыл бұрын
Thanks!
Amazing job! Well done 👏
@ForgottenShineRestoration
3 жыл бұрын
thank you!
Beautiful. Nice paint choice
@ForgottenShineRestoration
3 жыл бұрын
Thank you!
Excelente trabalho. Ótima escolha de cor. Parabéns 👏🇧🇷
@ForgottenShineRestoration
3 жыл бұрын
Muito Obrigado!
Well done, great video and restoration.
@ForgottenShineRestoration
3 жыл бұрын
thank you
Turtle's first appearance.................................... The LORE.......................................
@ForgottenShineRestoration
Жыл бұрын
That's true 🤗😳🐢
That is a handsome vice! I hope you get to keep it!
@ForgottenShineRestoration
2 жыл бұрын
Yes, I still have it in the cupboard... 🐢
Excelent Job
@ForgottenShineRestoration
Жыл бұрын
Thank you! 🐢
Lovely job well done mate😀👍⚒️
@ForgottenShineRestoration
3 жыл бұрын
Thank you!
..y resucitó, por lo menos durará más de 100 años . FELICIDADES. Saludos desde Barcelona Catalunya
@ForgottenShineRestoration
Жыл бұрын
Gracias 🐢
Güzel ve başarılı bir çalışma oldu. Tebrikler dostum.
@ForgottenShineRestoration
3 жыл бұрын
Merhaba Hüseyin Cengiz. Harika yorumunuz için teşekkürler, diğer videolarla iyi eğlenceler ...
This is german handcraft!🇩🇪
@ForgottenShineRestoration
2 жыл бұрын
Vielen Dank!😊🇩🇪
The "fix" is an indicator of whether or not it's broken, the fact that it's still there means that you still need to fix something
@ForgottenShineRestoration
Жыл бұрын
😅😅🐢
Muy buen trabajo!!!!! gracias por el video señor Dios le bendiga su inteligencia. Me gusto mas que todo la parte que regenero de atrás quedo perfecta!
@ForgottenShineRestoration
3 жыл бұрын
¡Muchas gracias por este maravilloso comentario!
Very nice restoration !
@ForgottenShineRestoration
3 жыл бұрын
Thank you!
great. You do well, I love the way you restore such vise. I also do such restorations in my videos! I learned a lot from you.
@ForgottenShineRestoration
3 жыл бұрын
Thank you!
Wow so much videos in such short time man!🛠 You will pass me soon!😍
@ForgottenShineRestoration
3 жыл бұрын
Hello cool restorations. Thank you very much, but it doesn't depend on quantity but on quality and I will do that now ...
Keep up the good work! Fun to watch. I hope you get a ton of followers! I’ll follow
@ForgottenShineRestoration
3 жыл бұрын
Thank you very much!
Good video and a well done repair. As to the blackening, I would choose chemical over heat every time. The heat can damage delicate springs and other parts and effect the temper. Keep up the excellent work and keep them coming.....
@ForgottenShineRestoration
3 жыл бұрын
Thank you!
Liked and subscribed. That looks amazing you have the skills to bring that back to life. I restore vintage axe heads and knives.
@ForgottenShineRestoration
3 жыл бұрын
Thank you!
good job💪👍
@ForgottenShineRestoration
3 жыл бұрын
Thank you!
Good job
@ForgottenShineRestoration
3 жыл бұрын
Thank you
Very nice work...
@ForgottenShineRestoration
3 жыл бұрын
Gary Jones thank you
@garyjones2582
Жыл бұрын
I love your perfect handle screwdriver 🪛..
good work
@ForgottenShineRestoration
3 жыл бұрын
Thank you!
Ficou muito bom 👏👏👏
@ForgottenShineRestoration
Жыл бұрын
Muito obrigado! 🐢
Good job!!! Like!! 👍🏽👍🏽👍🏽
@ForgottenShineRestoration
3 жыл бұрын
Thank you very much!
What brand of spray primer did you use?
Good idea
@ForgottenShineRestoration
3 жыл бұрын
Hey Ang, Thank you!
Looks great Enjoyed your video so I gave it a Thumbs Up
@ForgottenShineRestoration
3 жыл бұрын
Thank you!
@oneshotme
3 жыл бұрын
@@ForgottenShineRestoration You're welcome
Hey! I appreciate the effort you put into this, I know how much effort it takes to make these videos. So here are my thumbs-up, and a sub to help out your channel! All the best to you and your newfound channel!
@ForgottenShineRestoration
3 жыл бұрын
Thank you for the great comment! I wish you and your channel good luck too!
Sweet 👍🏼👍🏼
So what’s the benefits of stick welding the piece together rather than mig welding it?
Nice job my friend😆👍... Greetings from Greece😃
@ForgottenShineRestoration
3 жыл бұрын
Thank you! Greetings from Germany 😁
@simplescrapping
3 жыл бұрын
I give you a subscribe to you. If you could subscribe to my channel I will appreciate it. Thanks in advance😁
I have a vice this size,it as no interactions on who actually made it but it's very well made and I guess very old ,after restoration it's the hub of my workshop with it built-in anvil,not restored to your standard of craftsmanship but fully working and cost me very little in purchasing and materials used !
@ForgottenShineRestoration
3 жыл бұрын
Thank you for your comment! Yes, the vice is the most important tool in a workshop, I am of the same opinion! Since I bought it unseen, I didn't know how big it is, because this size is rather unwieldy, the small one I always use in my videos is always in use ...
I love watching your restorations and the inclusion 🐢
@ForgottenShineRestoration
Жыл бұрын
Thanks a lot! 🐢
Hard work.
@ForgottenShineRestoration
3 жыл бұрын
Bebel 68 indeed
but i got one thing to ask were dit you get al that things pleas awnser this
Not at mymechanics level, but almost!
Great video. Have given me inspiration to repair my vise. What product did you use for the browning on the handle it came out really good
@ForgottenShineRestoration
2 жыл бұрын
😊😊🐢
Subscribed. Lol that grease looks like leather glue 😂
@ForgottenShineRestoration
3 жыл бұрын
Yeah that looks really funny :)
Curious why you used body filler under a textured paint?
@ForgottenShineRestoration
3 жыл бұрын
Yes, so that the surface looks better
Bonjour, vous avez fait un très beau travail et l'étau en lui-même et magnifique et certainement robuste. Quellel type de couche de fond, avant de le peindre, avez-vous utilisé? Merci et meilleures salutations.
@ForgottenShineRestoration
3 жыл бұрын
Merci beaucoup! Ceci est un apprêt universel, ce n'est pas une peinture spéciale. Si vous avez également l'intention de travailler avec de la peinture Hammerite, cependant, il n'est pas nécessaire d'appliquer un apprêt au préalable, je ne le savais pas à l'époque. Hammerite peut être brossé directement sur le métal de la planche. Meilleures salutations
Muito bom
@ForgottenShineRestoration
2 жыл бұрын
Muito obrigado!
Hey! Awesome video! I loved to watch this restoration. Subscribed! What camera do you use for record? (Your video have a very good quality)
@ForgottenShineRestoration
3 жыл бұрын
Thank you for your great comment! That means a lot to me that you watched my video. I am currently still filming with my smartphone Samsung Galaxien s20 .. 🙈
@WorkshopDC
3 жыл бұрын
@@ForgottenShineRestoration I record with a smartphone too. You are doing a good job! Keep It up!
As soon as i saw that turtle i hit subscribe,i'm that turtle's biggest fan!! ;-)
@ForgottenShineRestoration
3 жыл бұрын
Thank you! The turtle is finally getting the attention it deserves!
@haemhorrhoidian
3 жыл бұрын
@@ForgottenShineRestoration He's my hero!! :-)
Они ж итак работали, всего лишь почистить от ржавчины и смазать надо было. Мне бы такие тиски =(
good
@ForgottenShineRestoration
3 жыл бұрын
Thank you!
6:46 ГЛАЗА!
How did that welding trick with the copper plate work?
@ForgottenShineRestoration
2 жыл бұрын
During welding, the weld metal does not bond with the copper, that's all
Do you not have any belt sanders or anything?
@ForgottenShineRestoration
3 жыл бұрын
Parker P unfortunately not :(
Muito bom gostei !
Nice work. Buttress thread, you don't see that very much
@ForgottenShineRestoration
3 жыл бұрын
Thank you!
Amei
@cybercilen1149
2 жыл бұрын
tbm gostei bastante
@ForgottenShineRestoration
2 жыл бұрын
Muito obrigado!
Probier mal einen OLFA-Cutter mit 9mm-30°-Klingen für das Mesh-Alu-Tape..
Ficou melhor de quando saiu da fábrica. 👏👏👏👏👏👏👏👏👏👏P. A. R. A. B. É. N. S 🙏🇧🇷
@ForgottenShineRestoration
2 жыл бұрын
🤗😱🐢
Like 54 Great vedio 👌 New friend 🔔 ,
@ForgottenShineRestoration
3 жыл бұрын
Thank you
@saadghauri1781
3 жыл бұрын
@@ForgottenShineRestoration sinscribe back buddy
👍👍👍
@ForgottenShineRestoration
3 жыл бұрын
Thanks!
У меня вопрос,зачем выкладывать видео которое уже есть на канале.зачем повторятся?уже смотрели это видео.
Do you have any stickers of your channel? I collect my favorite restorers stickers and put them on my toolbox
@ForgottenShineRestoration
Жыл бұрын
Of course I have stickers, write me best an e-mail with your address, then I send you some... 🐢
@jamesfield5346
Жыл бұрын
@Forgotten Shine Restoration ok sweet
Can't do this, don't have turtle
@ForgottenShineRestoration
3 жыл бұрын
smilodnfatalis55 to bad :D maybe i'll try it again with another animal
104 pounds I doubt that
You missed a spot.
OH BOY, YOUR ONE OF THOSE COMEDIANS WITH THE RUBBER DUCKIES HUH? STICK TO THE RESTORING LOLOLOL YOURE BETTER AT THAT
@ForgottenShineRestoration
3 жыл бұрын
Hey Nick. Thank you for your comment! :)
Why? Why did you use a body filler when you have all the welding skills needed to fill the voids with metal? You already filled other voids with welding. You welded the metal plate onto the anvil area, welded new corners, and the voids near the top of the jaws. Personal opinion, as I detest "fake" restorations . To me, my opinion, body filler with putty or epoxy will break easier, and is a lazy man's way of making something look pretty. MY OPINION! All those scrapes add character. Consistency is important... MY OPINION.
@ForgottenShineRestoration
2 жыл бұрын
I agree, spackling there was the wrong way to go, I realized that after the fact, thanks for your feedback!
you restored it badly . don't do these things . because you are not master . this is the truth . you shouldn't grind your vise mouth and you've done so wrong things . excuse me
@ForgottenShineRestoration
3 жыл бұрын
What exactly is badly done? You have to be more specific!
Looks like junk. Sloppy paint, visible unfinished areas, grinding marks, terrible "finished" product.
How to lost real soul of old tool....destroy all nice. This can do anybody. But why they didn't it ? Think about it,man. I don't like it. Sorry...!
pretty poor job to be honest