How To: Whirlpool/KitchenAid/Maytag Thrust Bearing Kit 12002213
How To Replace: Whirlpool/KitchenAid/Maytag Thrust Bearing Kit 12002213 www.appliancepartspros.com/whi...
Symptoms: Washer won’t agitate during use, drum won’t drain, or loud noise during operation
Tools: needle nose pliers, flathead screwdriver
This Whirlpool/KitchenAid/Maytag made Washer Thrust Bearing Kit replaces the following older part numbers on Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Sears, and Kenmore Washers: 1042142, 12001797, 12002213VP, 12500036, 21001218, 21001298, 21001733, 21001734, 22004258, 22004259, 35-2016, 35-2078, 35-2119, 35-2318, 35-2439, 35-2441, 35-2683, 35-3455, 35-3457, 35-3829, LA-2007.
Buy the new Washer Thrust Bearing Kit 12002213 here: www.appliancepartspros.com/whi...
Most orders delivered in 2 business days or less.
If you enjoyed this video, please click the like button. Subscribe to this channel for more appliance repair tutorials.
If you need any more technical advice, call us at 1-877-477-7278 or chat with us on our website www.appliancepartspros.com/. We're available 7 days a week.
For more appliance advice, information, and tips, follow us on social media.
Facebook: / appliancepartspros
Twitter: / applpartspros
Пікірлер: 66
I have the MAV7700AWW and like many others had an issue with the C clip. I noticed when I took the old washers off there was a spring-type washer that was not in the new kit - which probably made the assembler's life a whole lot easier getting that C clip on. I also noticed that the plastic collar did not seat flush against the new metal roller bearing, so I did end up squeezing to two together prior to assembly with my needlenose pliers but I still had an issue with that C clip. I used my flathead screwdriver and inserted it into the groove where the C clip goes to push back the new assembly as far as I could while inserting the ends of the C clip, but it was still a bugger to get that C clip on. Not nearly as easy as the tutorial makes it look, but doable.
My washer is 20 years old. About 10 years ago this repair was needed re wet clothes after the spin cycle. I used the thin washer then and it worked. Ten years later clothes were getting wetter again. Again I used the thin washer, it placed the arrow where it should be when rotated but did not cure the wet clothes. With no other option I placed the thick washer in. Although I shaved the edge of the C clip retainer, not enough of the groove was exposed to get it on no matter what I did. However, I solved it and perhaps the solution might help others. Using a Dremmel I ground the edge of the washer down at an angle on the outer facing side, exposing the groove and allowing relatively easy insertion of the clip. The machine now works fine again - the thick washer did the trick. Great video.
The C clip was a pain in the butt! My 1999 MAV7600AWW washer stopped spinning, and the pulley was totally trashed inside. We had to file down the C clip ends to even get it close to the channel. But now everything works awesome, and the spin cycle almost dries the clothes for me! We also replaced the belt since it was trashed, too. Thanks for the help!!
Excellent tutorial! I ordered my parts from your site, they were exact fit! Took 20 minutes and we were back up and running. Thanks!
Great video. I did have a lot of trouble with getting the C clip back in. I had to go out and buy a long pair of needlenose pliers, and I had to make sure that the smooth side of the C clip was against the washer. Thanks, you saved me $100.
@appliancepartspros
9 жыл бұрын
Matt Brody Awesome, glad the video helped you get the washer fixed and you saved some money!
Thank you! I followed your directions and now my old washer works like new! I had a fancy front loader it was nothing but trouble. top loaders are the way to go!
Very clear instructions and great work on the production end of this video. Thank you!
@appliancepartspros
5 ай бұрын
You are welcome. If there is anything we can help you with in the future please let us know.
Great video, you guys rock!
My washing machine had a problem where it was not spinning, I turned it on while tilted to watch the belt operating and it seems to be working fine. Turns out to be a broken E-Clip, the whole pulley assembly was just falling off the main rod... Replaced from Lowes at ~$2. Works as a charm now!
Great video! I would like to add the following notes for diagnostics. My washer could agitate and pump water but wouldn’t spin. Years before the thrust bearing failed the washer would squeal when the spin cycle would stop. Near the end the washer would make noise during the cycle and it sounding like plastic cracking/grinding. The E-Clip is hard to insert. I used RoboGrip pliers from Sears and made sure the Lower Cam was rotated until the maximum shaft was exposed. Hopefully this additional information helps somebody.
@appliancepartspros
7 жыл бұрын
Thanks for those tips, Thomas!
@kimmeyer370
2 жыл бұрын
This sounds EXACTLY like my washer. I'm going to try this fix. Thanks!
Thanks for the video, super helpful!
@appliancepartspros
6 жыл бұрын
You're welcome!
Thanks a million, this video helped a lot!
@appliancepartspros
9 жыл бұрын
Daniel L Glad the video helped you get the washer working!
@bludhair5658
2 жыл бұрын
Your banner is sus
Gracias 👍
Great instructions.
@appliancepartspros
7 жыл бұрын
Glad the video helped you get the washer up and running!
Installation steps were dead on. Thank you! I replaced the brake rotor and stator, snubber ring, pump and drive belt to hopefully get another 11 years from this Maytag washer :D
@appliancepartspros
8 жыл бұрын
+MrJFunk Sanchez Glad the videos helped you get the washer fixed!
Thank you.... It worked for me.
@appliancepartspros
7 жыл бұрын
Happy to have helped!
@stevebollinger7282
6 жыл бұрын
AppliancePartsPros my performa agitates drains but will not spin ?
Had the thin washer didn’t work. Changed to thicker one still didn’t work.
where do you grab the lower cam to rotate it so its out as far as it will go?
After replacing your thrust bearing... It’s also a good time to replace your water supply hoses, if they are a few years old.
After removing the break drum and cleaning it , replacing the thrust bearing and now the shaft doesn’t stick out far enough to insert the E-clip . What is my next step to remedy this
@Rich9351
7 ай бұрын
I have the same problem. Any suggestions yet?
@paulmike3
2 күн бұрын
I sanded/filed down the middle of the pulley, per what I saw others on the Amazon parts reviews say to do. Finally got enough clearance to get the C clip on with some massive force.
I appreciate telling the symptoms of a bad thrust washer kit. So many do not explain the symptom of a faulty part.
@appliancepartspros
5 жыл бұрын
We're happy to help!
Que Pasa Si Coloco Mal la Pieza De Plastico Blanca Que Biene Dentro De la Polea Si la Coloco Voltiada De Favor Me Pidrian Contestar Gracías y Saludos Desde las Montañas Mty NL
I now have a Maytag with the same belt drive be system. Makes bad rumble when agitating. Also spins while draining. I am thinking transmission. Comment? Btw, spins fine with no noise.
I have the same machine as the one just worked on. I have some oil leaking from the transmission, would installing this kit stop the oil leak?
@appliancepartspros
10 жыл бұрын
This kit does not have any oil seals. Please call us with the model and serial numbers of your washer so we can see what seals are available.
My maytag performa/atlantis , somtimes spins then wont or just wont spin at all,, How do you tell the difference between an issue with the brake, transmission or the thrust bearing ? And Does the thrust bearing act as the clutch for the spin cycle ?
@appliancepartspros
6 жыл бұрын
We'll be glad to help you figure out what's going on there. We offer free technical advice and diagnosis. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need your model number, which you can locate using this tool on our website: www.appliancepartspros.com/modelnumber_locator.aspx
what does the plastic bush do? my maytag makes a noise when spinning and then dies down. I replaced the thrust bearing though I never got the plastic bush with the new part and instill have the same sound..slightly fainter
@appliancepartspros
7 жыл бұрын
Without knowing what you have, I would suggest posting the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem. forum.appliancepartspros.com/
I followed the installation instructions and used the thin washer, but now I cannot get the C clip back in. There is not enough room for even the thin washer? what do I do now?
@shakeme3290
3 жыл бұрын
Pull on the shaft with pliers to get the tiny bit extra to get the clip on
I changed my Thrust bearing on my maytag MAV7600AWW I used the thinnest washer and its to tight for the arrow to fall in between the 2 marks and it wont engage the drum to spin. Any ideas?
@appliancepartspros
10 жыл бұрын
You can post this problem along with your model number on our repair forum and the techs will help you out.
@Rich9351
7 ай бұрын
Will this repair work without the washer if it is within the two lines? It spins fine now, but do you know if there will be any longer-term problems with no washer?
my clothes are still soaking wet at the end of the spin cycle. the drum spins but not fast enough to pull the water from the clothes. will this fix the problem?
Hi, I change the whole kit and I can't get through to adjust the transmission. When I turn the pulley the inner white part turns together with the pulley and I can't adjust the transmission. And the shaft does not pull out to install the thicker washer. So I need help. Thanks.
@benjaminjohnson9576
3 жыл бұрын
I am having the same issue. Anyone figured out a resolution to this?
I didn’t have enough clearance to put the e clip back on. I put it on without the washer is that going to screw up anything?
@shakeme3290
3 жыл бұрын
Well you should know by now. Did it?
@Rich9351
7 ай бұрын
I'm wondering the same. Any problems yet?
what is the fault of this same model of washing machine since it only rotates counterclockwise.
@appliancepartspros
6 жыл бұрын
We'd be happy to help you out with that! We offer free technical advice and diagnosis. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need your model number to give you accurate advice, which you can locate using this tool on our website: www.appliancepartspros.com/modelnumber_locator.aspx
Sos mi pollo
There are *no* Whirlpool- or KitchenAid-branded washers that take this part/kit.
The trick to getting the clip on with the new parts is to cut yourself, grow a third arm, cuss at it alot, and then try to occupy the same space with 3 different things.
@appliancepartspros
15 күн бұрын
If there is anything we can help you with in the future please let us know.
This is a great How-To repair video. However, it would be nice if you could spend 30 seconds on the front side to help diagnose the problems created by a worn thrust bearing. You state 3 things, two of them are operational and probably easier to figure out. The "Washer is Noisy" is a little vague. It would be fantastic IF you could give an example of what to listen for. Thanks for the Repair Tutorial!!!
@appliancepartspros
9 жыл бұрын
kthom2001 Thanks for the ideas, hope the video helped you get the washer fixed!
@1984juant
8 жыл бұрын
i agree. diagnosis is more important than replacing part.
Based on the info available here, I replaced the Thrust bearing, thinking it wasn't disengaging and allowing the tub to spin. In the end I needed to replace the Pump, as the bearing was shot and it was seizing up and preventing the tub from spinning consistently.
@appliancepartspros
9 жыл бұрын
kthom2001 Glad you were able to find the bad pump and get the washer up and running!
Frustrating spent 4 hours on it