I've been looking for a video like this. It's perfect. Love the lack of intro, and just the straightforward instructional. Thanks y'all

Nice job thanks for the the video helps a lot

I recommend:A) to use a flash metal as the roof color and you don't have to paint,B)use screws for deck better work than nails,C)silicone before installing 2by4,.

@mattsmith718

2 жыл бұрын

I would recommend: A) Use proper formatting when critiquing something you know nothing about. B) The color of the roof flashing is superficial, more concerning is the improper lapping they did from top of 2x4 to sheeting.

@GabrieLight

Жыл бұрын

@@mattsmith718 Hey Matt, Do you have a good video that show the best method for installing the skylight?!

This video was a huge help. Confirmed what I was going to do. Thank you!

Why would you put flashing over the shingles? I know you put the waterproof membrane below, but it seems like the space between the membrane and the flashing could give you mold growth.

MUY bien. Gracias

is it normal for there to be no insulation in this part of the house?

Please help! We have a skylight in our manufactured home. Back in 2007 we had metal roofing put on and they lifted our skylight 4 inches with 4" boards. The boards were able to be seen from the inside of the bathroom, so to satisfy me the bent a piece of metal to fit around the opening to cover the boards. Every summer, when it gets extremely hot tar melts down into our skylight on top of the metal sheet they covered the boards with. How do I fix this problem?

My dad installed 2 of these yesterday in our new house and I didn't go to see so I'm just watching this to get an idea :)

Was building confidence and getting ready to start till I read the comments, maybe I'll wait.

Eric I am disappointed to see this type of work. I have watched your videos on the past and they are good, but watching how you used more that one course of shingles per tin shingle that is not right and you know it buddy that you most, no excuse use one tin shingle per course of shingles no exceptions, and on top of that you paint your metals after you install them and you did not protected the shingles from your spry pain those are some of the most expensive shingles on the market. I would not enjoy getting on my roof to look at the Ski light and find spry paint on my expensive roof, don't let your guard down man I am a roofer my self and I like your videos a lot, good luck and keep up the good work

@kroalex81

5 жыл бұрын

I agree I been watching Eric's videos and now I saw this video very disappointed

@johnlieb1

5 жыл бұрын

it also looks like he put the I&W on top of the underlayment and not to the deck

se ve bien cuanto Cobra por poner uno asi tengo ganas de unos dos en el sun room.

Wow is that step by step?? So impressed

Cool video. Which Automated skylight is this?

Enjoy the nights when the skylight leaks

@carlito3094

4 жыл бұрын

Lol

We use deck screws here.

What kind of plung saw is that. Looks comfortable

The old days of corded tools.

@mattsmith718

2 жыл бұрын

Corded tools always have, and always will provide superior power and lasting abilities.

@germanborgesxrt

Жыл бұрын

@@mattsmith718 I agree, never a problem.

Can you mount a fixed mount skylight in either direction? Or is there a specific top and bottom? Since neither side opens, is there a correction orientation?

@mattsmith718

2 жыл бұрын

Stupid question as the skylight installed clearly showed it not only opened and closed in a sliding manner, but also had a screen attachment as well. Like everything else in life, this product would have come with installation instructions clearly stating the correct orientation of the skylight.

Im looking for metal roof videos, watched this, no step flashing? this is not correct. You must use step flashing for shingles.

@Deenihan18

5 жыл бұрын

At 6:02 there's step flashing or at least some "homemade step flashing" on the left & right sides.. but that's the least of issues w this install.

@Inzanezombie

5 жыл бұрын

Deenihan18 Do u know any proper metal roof install vids

@qmax-en5ry

3 жыл бұрын

You don't have to use step flashing, not necessarily, but this video has step flashing. I'm not really convinced about the quality on the bottom and top flashing on this video, it looks pretty crappie

everything except installing the skylight...hmmmm

@theguyinthehelmet1875

5 жыл бұрын

Homeowner installed the skylight.

Could that be used as a way onto the top of the roof, with a pull-down ladder?

@theguyinthehelmet1875

5 жыл бұрын

No. Different construction applications.

Solo quiero hacer dos observaciones una por que no pintan los metales antes de ponerlos y les falto un pedaso de shingle en el primer tin shingle y la ultima no pusieron los tin shingles en cada linea

@Garciasroofing

8 жыл бұрын

1: Si pintas los metales antes , la pintura se despega del metal con el tiempo y si usas mastick , se goteara por que el agua pasara por debajo de la pintura despegada , haciendo el silicone o mastick inservible. 2: usamos tin shingles de 8x12 con silicone para prevenir que el agua se pase entre en shingle y el metal por eso se miran grandes, se pueden usar los de 5x8 pero es mas rapido y da el mismo resultado usar los grandes. 3: en el presidencial se usa un pedazo de starter cuando el shingle no cubre el metal para que se mire mas estetico, pero en este caso , a la gente le importa mas no tener goteras que un techo bonito, con esto te digo que los techos son solo para un proposito, para asegurarte que durante 50 yrs. o mas no tendras goteras que eso si danara lo estetico como lo es el drywall y la pintura, carpeta, pisos , etc...ademas nuestro trabajo no se mira tan mal como la mayoria de techos que he visto . lo prodria haber hecho mejor lo se , pero al menos , enseno algo al que mira mis videos, mira otro videos y ni siquiera aprendes nada, solo miras a alguien cuando termina y ni siquiera te dice como hacerlo . gracias. Eric.

@alfredosanchez2677

6 жыл бұрын

Adrian De La Cruz mis wevos como se va a despertar según trabajas bien limpio y según te crees el muy buen roofero pintando la teja conespray no soy tan bien rufero pero como dice el chavo pinta las láminas ntes para ke no agas un cochinero el la teja

@theguyinthehelmet1875

5 жыл бұрын

English please.

No way jose !!bab bab work!!

Well, at least you videotaped and published. That will make the discovery go quickly.

@lisacolbert5987

Жыл бұрын

Hahaha , right ? These guys are hacks. And I’m not saying that bc they are Spanish speaking brown people , no. I’m saying it bc I know how to install a curb-mounted skylight , have installed several in my life ,,, and this is SO full of f**k-ups , it’s criminal. I give it 2 maybe 3 good precip events and the nightmare will begin. Even if this was installed in the southwest , when it rains there , it tends to really pour. But , you know , when you do work like this , just change your phone number - often.

@RoofingFacts

Жыл бұрын

@@lisacolbert5987 I knew a fella who bought a bunch of car magnets all the same size, including numbers. Had them cut up so he could swap the name and logo constantly and had multiple magnets of every number all in the same font. He could literally swap his work trucks identity driving home to home. The good news was they eventually caught up with him for fraud (no license, took money and left multiple times, I think tax evasion was even in there). They got him for 5 years in prison, I think it was 3 year ban on his license, and a fine worth less than he took.

How you guys got the initial cut opening beyween the main beams. Lol

I would opt fpr my cut to break beyond an overlap, or little shingle flap. Just cause anything that runs down and then around the skylight will now be forced under that one flap on top, sure there's flashing gonna be around it but i still think like that no matter what.

Ke onda Eric buen jale

I'm replacing my curb mounted bubble skylight because it has developed cracks. When I went up to measure I was surprised to find out the skylight is not attached to the curb. It is, literally, sitting on top of the curb with no screws to hold it on. I was able to lift it right off to measure the curb. That seems weird to me because even if the high winds out here haven't lifted it off it still seems like a security issue. Anybody could lift it up and drop right down into my bathroom! The skylight is at least 25 years old, maybe older. I had a new metal roof put on in 2012. I don't know if the skylight was always just sitting up there like that or whether the guy that did my roof didn't bother to reattach after finishing the roof. After searching high and low on line I was finally able to order a new Velux bubble skylight. It hasn't shipped yet but I'm trying to prepare ahead of time for installing it. I have a metal roof and there is metal flashing installed up the sides of the curb. Do I need to put anything between the skylight and the flashing? Was that stuff you were spraying some kind of water proofer or was it just paint? Your video didn't show the actual attaching of the skylight to the curb. I won't know until the skylight gets here whether it has screw holes for attaching to the curb. I'm hoping it does. Thanks for taking time to read my long question! Eva

@Garciasroofing

7 жыл бұрын

if you have a gap between the skylight and the frame where it's mounted , usually the skylight seals any mosquitos or bees penetration when you mount it on the curb. at any hardware store they sell a thing that is called weather seal or tape and you stick it around the frame before mounting the skylight. to secure the skylight you can use 2 inch galvanized nails or metal screws , 2 nails or screws on the longer side and 1 on the short side should keep it in place. usually the skylights are design to divert the wind that's why you went so many years without nails. hope my answers could solve your questions , good luck. Eric.

@Garciasroofing

7 жыл бұрын

i was just painting the galvanized flashing to match the color of the roof, when they replaced your roof , they forgot to re attach the skylight in place , in order for them to install the flashing under the skylight , the had to remove it and forgot to install the screws back. thanks for you comment . Eric.

@EvaFitts

7 жыл бұрын

Thank you so much for taking the time to respond! I'm excited for the skylight to get here now. I'm ready to tackle the job :)

@dustypirate6775

6 жыл бұрын

Where Is The Proper Step Flashing???

In the beginning of the video at 00:40, weren't ypu scared that you would end up cutting the rafters? How did you make sure that the saw cut just the top of the roof?

@jkulysses

7 жыл бұрын

Just adjust the saw cutting depth to whatever the size of the plywood is 1/2" or 3/4" or whatever it may be.

@tandalat

7 жыл бұрын

Also, since they shot screws upward from the attic. The markings should've guided them not to go over the rafters. I did all cuts in one pass (ie. cutting both plywood and purlins at once).

@theguyinthehelmet1875

5 жыл бұрын

Apparently, you didn't see the video all the way to the end. The ceiling is open from below. They were able to predetermine the location. Think about it: how was it that they could cut and they were dead on between two rafters. 😊

Si es en un lugar donde casi no llueve no va a haber gotera, pero donde llueve mucho se va a gotear.

The back pan is incorrect, not even close to correct. Spray painting on a roof is risky business. Use flashing for over spray. I guarantee you that the skylight will leak. The top two corners. Just copy the old technique. Should not be flush to curb. Place another back pan and redo correctly. This is not correct and slopy.

@sevenhighclub2339

3 жыл бұрын

These are not real roofers at all.

@traceyivy1953

Жыл бұрын

Oh sush..get your own show then

Good Job! Jose 😄💪💪

Fierro pariente, como lo hiciste osea freimeaste adentro

Improper installation: the head flashing was not overlapped correctly with underlayment in shingle manner. The side step flashing was not woven between shingles. If it did not leak as "you claim", you've got VERY lucky. There are other variables that determine leakage when such poor installation is performed such as climate zone, roof's pitch, wind driven rain, etc...

@lucentnative4363

2 жыл бұрын

They probably don't get.much rain

how did you finish the inside

How is it holding up ?

mmm, just spray over the gaps in the roofing ? . Don't call us !!!

I would of thought you put some sealant between boards too. wouldn't hurt and save the job from leaks down the road.

la reflashada no esta bien le faltó definición de criques por los dos lados

@gerberhenriquez2481

3 жыл бұрын

Si Jairo; nada profecional , eso es un cochinero, chip work..

Me gusto..cuando pie den hacer el mio🇨🇦

@gersongarcia5503

4 жыл бұрын

Cuando quieras voy yo

Yo entiendo lo que dices pero Es contradictorio lo que escribistes por que muchas veces dices que todo lo haces dela forma correcta y dices que lo estetico no importa solo que no se meta el agua tienes muy buenas ideas pero algunas las tienes que mejorar yo tambien soy roofero pero si hay muchas cosas que se te pueden aprender gracias

@phillipjones1122

8 жыл бұрын

step flashing is installed incorrectly ....it's going to leak

Pinche vídeo sarro !

Perfect job

Using a skill saw as a handsaw, a crosscut saw and a multi tool, ... and you still need to have an assistant grab the end of a 16-21 inch cutoff? Wtf? Nice creases on the flashing. I’m sure that skylight sat beautifully. Tape or at least cardboard the next time before you graffiti the shingles, huh?

@danielpack388

5 жыл бұрын

My thoughts exactly.

@williamgeorgelopezjunior8533

5 жыл бұрын

It’s why we can’t have nice things, Daniel! 😝

Eso es lo más fasil de instalar

Nails to the frame? Oh. Did you hear some thing about skews?

Practico y sin tanto hanlar 😂bien echo muchachos 👌🏽👌🏽👌🏽👍🏾👍🏾👍🏾💪🏾💪🏾💪🏾

if anyone's flying over your house, they can look in

@cxMLG

5 жыл бұрын

See you beating the meat

@macrip78

5 жыл бұрын

@@controllyourself8144 LOL!!!!!!!

How did you know where to cut

@thehamstaa5148

4 жыл бұрын

I've gone as far as to paint the inside of the curb white to match the interiors.. good work Eric

David fromm you are right... Everything except how install skylight... By the way it was an ugly flashing maybe try a metal brake it would look nice instead bend the metal with the hammer

@Garciasroofing

5 жыл бұрын

Alex Medrano ...that skylight was done about 3 years ago. Till now it hasn't leaked yet. The problem with roofs is this: people want to see cosmetic roofs. Remember roofs are not for cosmetic view the only purpose of a roof is to last at least 30 years . leak free. I was trying to show a simple way to do it with simple materials. Many people don't get the main idea yet. 😢 sad

Installing roof air condition on a curb

India 🇮🇳🇮🇳🇮🇳

Your approach is well, the first mistake is your wooden box it should have at least 6 inches in height because of the storms with lots of waterFor the rest your technique is good!

@mattsmith718

2 жыл бұрын

Gee thanks for response to a question not even asked. Here is a question for you: Do you know where this build took place and further to that point do you know what the local building codes, and weather patterns are? Here is another question for you: Were you born a mentally handicapped floor licker? Or is this just an acquired skill of your?

@baiebell1

2 жыл бұрын

@@mattsmith718 Usually this kind of comment is made by people who feel guilty.

@mattsmith718

2 жыл бұрын

@@baiebell1 Imagine being so mentally stunned you think you are able to determine a strangers emotion based on a single paragraph you read on You Tube, you are a cancer sir.

Exactly, one cut would have done it. Cut the osb once around the outside scored perimeter of skylite frame and you would have been golden. Not the inside of the frame...perhaps, this is why they aren't carpenters...yeah, stick to roofing, dude. Seriously.

@justind6343

5 жыл бұрын

That would put the skylight too low for many counter flashings and increase chance of leaks. Size up to a 2x6 to compensate and you get increased lever forces and warpage affecting your curb. Keyboard warriors, always nitpicking. Are you a carpenter? Maybe you should try roofing.

why no cricket on topside of skylight?

@Garciasroofing

8 жыл бұрын

+Jim Welch because you only need a cricket when it's 30 inches or more , plus skylights don't required a cricket , That's per code.

@jimwelch7252

8 жыл бұрын

+Roofing Solutions By Eric Garcia depends upon the city's building code it varies in different counties...any standing water will eventually cause damage but I do like your prep and application.

@Garciasroofing

8 жыл бұрын

+Jim Welch , So far I haven't seen any cricket on the top side of the skylights,I live in CA , but I usually use a Peel &Stick Membrane around the skylight before installing the step flashing.

@jimwelch7252

8 жыл бұрын

There's a metal shop in Huntington Beach "Rick's heating and air conditioning" for custom metal work even copper...

@qmax-en5ry

8 жыл бұрын

there's no room between shingles and skylight flange to install a cricket, maybe 1 " but it will be useless.

Did anyone else notice the roofer didn't tie his shoe laces??

Primo tu a mi no me duermes, quitaste chingos y cuando cortaste todo estaba en escuadra ; quiero ver como lo hiciste.. Si eres bieno me vas a enseñar..

Hello

Que le exprayastes alli bicho?

Step by step? Didn't show the installation of the step flashing, pan or the skylight. Hmmm? Nice fall protection too.

@gersongarcia5503

4 жыл бұрын

Stop being a vagina, fall protection my ass.

this guys are not a roofers. they are home depot guys. 😂

Minuto 1.. 29 porque poner los dedos debajo sin qe la sierra pare por estupidos se cortan los dedos

Cuidado con la goteras .

If I did this I would lose my license. That house is going to FLOOD....

@Garciasroofing

3 жыл бұрын

You lost already...5 yrs after...the skylights hasn't leaked yet.. Lol 😆😆😆😆

@gerberhenriquez2481

3 жыл бұрын

Look ugly work .

@sevenhighclub2339

3 жыл бұрын

Roofing Solutions by Eric Garcia it was done wrong though

I installed this skylight 8 years ago or more , still not leaking , for all those MF that say I did a bad job , FU , I didn't greeting s . Eric Garcia

Nopinte conpren El kit nosean tracalas

title should be how to create a rain catcher... or a robber port hole.

This is a video how not to hire contractor doing this type of job. The proper way to install a skylite is done by Mohawk Guy on KZread.

no saddle ?

thanks for making this video but you don't show complet work lots of citing in this video

Never cut a hole in your roof.

@sevenhighclub2339

3 жыл бұрын

Why

Rápido se ve que es gente que levantaron del Home Depot por 130 el día 😂😂😂😂😂

@Garciasroofing

6 жыл бұрын

Creo que la gente de Home depot ya no cobra eso , los menos pagados aca son los lavatrastes, lava carros, fabricas, etc... Cualquier jornalero te cobra mas que una persona que trabaja de techador ( rufero) . Creo que estas mal informado amigo, si quiere emplear personas de las Home depot , le saldra mas caro ,en cambio un aprendiz de techador le saldra mas barato, Los que menos pagan en esta industria son las grandes companias de roofing por si no lo sabia , te matan por un sueldo miserable y encima de eso te matan trabajando las 8 horas del dia . Creo que no conoces bien este pais paisano . informate para que no te enganen buen dia .

@jhonwick9006

6 жыл бұрын

Roofing Solutions By Eric Garcia yo no me dedico a eso Para aclarar pero he visto trabajos que los dejan bien jodidos esa gente el contratista por quererse hacer rico en un trabajo ágata pura gente balazo

@alekxx35

5 жыл бұрын

Estas equivocado mi querido roofing solutions las compañías grandes de roof te pagan de acuerdo a lo que sabes, tienen máquinas para todo, ademas aseguranzas, te pagan holidays, sick days y cada quien tiene su función, solo los pequeños contratistas y compañías pequeñas hacen lo que tú mencionas, no creo tu les des aseguranza a tus trabajadores, ni pagues holidays no cosa por el estilo, sabes porque por el tipo de trabajo que realizas como dicen de acuerdo a lo que pagues es el trabajo que te harán, es por eso que muchos rooferos van a trabajar a grandes compañías y los rooferos buenos que hay solo trabajan en las pequeñas por una cosa la falta de papeles para trabajar.!!!

Everybody asking about skylight installation ...the guy build the fucking frame and flashing ...you just gonna drop the skylight on it and attach with screws 🤦‍♂️🤦‍♂️🤦‍♂️

Why they mark and cut for inside of frame😂😂😂😂😂

The flashing job sucks on this thing

@victoreous626

4 жыл бұрын

Painting, sawing were exemplary. Don't you think?

Zilcon Restoration Corp covering a full range of building designs, & envelope constructions, and types, for roofing, interior, and exterior/façade repairs and renovations. Whether for commercial buildings, industrial buildings, historical sites, office buildings, or warehouses, we have the skills and expertise to meet your building restoration & reconstruction needs

Ha, the way it was built, this sky leaked within 1 yr!

@Garciasroofing

4 жыл бұрын

Let me tell you...till this date ...the skylight hasn't leaked yet...when i did the roof i gave the home owner 10 yrs labor warranty on the shingles installation...short after he decided to open up the skylight...so i went back and installed the new skylight...i don't think it will leak... I skipped many steps on the video to make it short and swift...but it's waterproof my friend. I was done by Eric Garcia...not a fly by night roofer

@akramazeroual2175

4 жыл бұрын

@@Garciasroofing hhhhhh😂😂😂

Did you guys know that you can make a precision cut using the new methods of fire and make a skylight in the roof for half the price

This is going to leak

@onewaytosavetheday

4 жыл бұрын

How do you prevent it from leaking? I want to try installing one myself.

Where the flashing bruh smh half ass roofers smh no bueno

You can use Stodoys and plans. The best plans and very detailed instructions. You can learn a lot from them and do it yourself.

Muy mal trabajo . si yo miro q pintas los metales i pintas mi techo.te ago q lo cambies o tecorro muy feo el terminado..

@Garciasroofing

6 жыл бұрын

Lizeth Arroyo ....you are so funny 🤣🤣🤣👍👍👍

Estas perdido con tugente te voi amansar videos como se esos travagos

Or Stealing into the house XD

Man's shoes are untied. A real safety hazard when working on a roof.

Lol…that’s gunna leak in no time

@TheRayDog

3 ай бұрын

No doubt. A completely unsealed side? Crazy.

That's not gonna leak...

I hope the guy sawing made enough off of this job to buy some new boots !

Watching guys that work hourly is just painful man.

Todo iva bien asta que pinto los shingles. 🤦🏻‍♂️

That is so dangerous what you done. Lifting up the shield on the saw

Windows on roofs , are a stupid idea , no matter how you slice it

Keep painting those shingles...smh.

This is sloppy work. 1. Curb should have been 2x6. 2. Top and bottom 2x6 should go over rafters. 3. Should have diverters on back pan, and on step flashing at the bottom. 4. missing counter flashing. 5. step flashing done incorrectly. 6. they make colored flashing.....

Skipped (show)the most important part of the installation of the job .dan,,,,,,,m

Que asco de trabajo

Que mierdero hicieron alli

Do they have a green card

@voioo

4 жыл бұрын

p jay Jonás brothers

Fucken shocking and poor workmanship