Appreciate the video! Clear explanation and camera angles are really helpful!

Appreciated video but remember turn off dryer electrical power and a shut off gas supply, preferaly disconnect.

Thank Marshall for your tip. I recommend aluminum tape is more riliable

@MarshallHudson11

Ай бұрын

Yeah judging by the comments my next video might be how to replace duck tape in dryer with aluminum tape 😅

This is by far the best and only adequate DIY instructional video about a Samsung dryer side vent kit. However, I do wish you provided a little bit more detail. For example, you took the screw off the back and did something with it inside. Discussing that step in detail, as well as where and how those tabs fit together, would really enhance this video given the limitations of what can be viewed. Thx!

@MarshallHudson11

4 ай бұрын

Thank you for the feedback! It really helps for the future videos. The tabs should slide together and then the screw secures them. Really wish I could have found a way to put the camera on the inside but I couldn't figure out how to get it back out.

Good tutorial, thanks for taking the time to make it. As has been said, aluminum foil tape is superior, especially long term.

LOL Duct tape you mean aluminum tape I hope, duct tape will turn into dust after time

Hi there. How did u remove the circular hole. Ours doesn’t come proliferated. What tool would I need to use to cut a hole out? Thanks for your time and knowledge.

@MarshallHudson11

3 ай бұрын

You could use a dremel get a metal drill bit. I would check and make sure there is a tab that folds up inside first since that’s what’s hold the turn in place. Without it there’s a chance it could come disconnected.

Did you cut the hole in the side of the dryer? My dryer does not have any detente or outline for a hole on the side.

@MarshallHudson11

8 ай бұрын

Did not have to cut a hole there’s a knock out in both sides. You could probably drill a hole but then you’d need to make some custom tapes to hold the joints inside too.

Please provide the link for the side vent pieces.

@MarshallHudson11

11 ай бұрын

SAMSUNG Side Vent Kit for... www.amazon.com/dp/B01FM3HGOM?ref=ppx_pop_mob_ap_share

What tools did you use to punch the side hole out? I know it’s indented to make it easier but since I’ve never done anything like this before, I don’t know HOW to punch the hole out. Thanks in advance!

@MarshallHudson11

4 ай бұрын

I took a flat head screw driver and a hammer and just tapped it in circle motion until it comes free. I’ve seen people just take a big wack at it and it work but that makes me nervous

And there’s no “45” in there - it’s a 90 degree angle.

Can you please tell me what that item was that you used to cap off the back? Do you know where I could find this item?

@MarshallHudson11

4 ай бұрын

It's just a cover that came with kit. Here's the link to the kit below. I couldn't find one that was sold separately but you could probably make a 4 inch PVC pipe cover work if you didn't want to get the whole thing. www.amazon.com/gp/product/B01FM3HGOM/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1

I don't see the amazon link

@MarshallHudson11

2 ай бұрын

My apologies I just added to the description. a.co/d/fwf3bg0

Where do you buy the kit I can find them

@MarshallHudson11

23 күн бұрын

www.amazon.com/dp/B01FM3HGOM?ref_=cm_sw_r_cso_cp_apin_dp_KJXG7R0HMJT39KKQ6TM4&starsLeft=1&skipTwisterOG=2

You mention a tab but I don't understand where it is. You do a bunch of things that I don't understand with your arm in the dryer.

That looks like one of the dumbest inventions ever.. !

Metal furnace tape not duct tape it will catch fire