Excellent. Thanks for sharing. We need more instructional videos like this one, with wiring diagrams.

Thank you for sharing. Very nice to watch your videos. Greetings from Spain.

Glad I found this video.

Detail & Informative. Nice

great work sir

Thats Excellent u do good

Real Engineer

Ossam Video

It looks like the stop pushbutton is wired normally open so it will not fail safe.

Best

Can you please upload the pdf version of ladder program bcoz the video resolution is too low and could not be read? Thanks

Can you please tell m how to select MCB for servo motor, I have 1.5kw servo 6A current

If you can offer training, then technicians can buy your products for service in many industries. Do you?

Mr help me,,Is the plc cp1e n40 dt d used for 2 servo motors / 2 axis?

Hello can you help me, how to wiring motor controll to plc...tank you

How we change the mode programmatically ?

What would the in/out be used for?

How come the CX PLC programmer works with the servo controller? Are the servo controller commands standardized or can you configure them in the CX programmer? Oh I see you control the servo controller with a PLC you programmed. Can the PLC programmed to send a configurable number of step impulses to the servo driver when an input signal (like the Z signal from encoder) is received? I'm thinking this can be used for servo/spindle positioning

@ATOcom

3 жыл бұрын

Yes, these can be achieved. But I don't have CX.

How to know if I will be using Dm100 to control the servo motor?

does it work for all types of servo motor or only for the type wjich on this video ?

@ATOcom

4 жыл бұрын

Just for ATO SERVO motor，www.ato.com/ac-servo-motors

How to use the position control mode of the servo motor Amplifier Driver model : Yaskawa SGD7D-5R5A00A or not

Hi bud Can you help me connect servo controller of spindle motor to Sinumerik 808d? Please

How to show robot cycle time on omron hmi and omron plc

Hello there, can i ask what music you're using?

@Vivenk88

4 жыл бұрын

Not relevant to the topic but Shazam tells me it, "A Moment With you (Original Mix) - Tropical Bleyage"

what is V0.01?

How we can control the speed ? Using PWM or Digital Output ? And at which pin we have to send the signal.

@ATOcom

3 жыл бұрын

To control the speed of the motor, you only need to adjust the pulse output frequency (adjust the frequency storage unit data in the "SPEED" command, D100 in the video). The pulse output is used here. The speed signal can be output by 100.00 and the direction signal by 100.02.

@shahzebkhan3392

3 жыл бұрын

@@ATOcom can we change the mode programmatically like pr000 etc

Basically this work like standard inverter ac motor ... no positional moving programming here... 🤔

Por que no controlan directamente el driver con la salida del plc? porque usan reles en vez de usar los contactos del plc?

@ATOcom

4 жыл бұрын

To protect the PLC

Hi. What is the NC for on the PLC itself? I dont see anyone use it and the manuals also dont explain whats the purpose of it

@ATOcom

4 жыл бұрын

Where do you see the NC, in the program or on the hardware? NC generally refers to the state of the contacts, normally closed contacts. There is also a normally open contact NO.

@lct9031

4 жыл бұрын

On the hardware... if you look at the plc, you will see when you hard wire your plc you have your terminals are labelled "+", "-", "COM", "01", etc but there are also ones labelled "NC"... what is the purpose of that terminal?

@ATOcom

4 жыл бұрын

@@lct9031 I get it, the NC you said refers to the empty terminal. Your PLC housing is shared by multiple models. The model you use does not use that terminal, so it is marked as NC. No wires need to be connected to that terminal.

This is speed control mode (continuous mode), not position control mode

Sir please ellaborate your vlog for beginers.

But sir pls upload a program on basis of servo motor with ball screw, slider movement.... Pls sir

@ATOcom

3 жыл бұрын

Refer to this video: kzread.info/dash/bejne/k4tsq8WHhJO_h7w.html

How to omron plc use model name send please

May I know why need to connect relay

@ATOcom

2 жыл бұрын

To protect the terminals of the PLC.

@electroniclover5589

2 жыл бұрын

@@ATOcom is because the npn and pnp

Hello.can you create a video how to use danfoss.thank you in advance..!

Sir me bhi sikhana chahta hu

Oke

Why could 100.00 and 100.02 work, whereas they're not be programmed on ladder?

@ATOcom

2 жыл бұрын

Because this is its dedicated port for pulse output.

@braineedly7543

2 жыл бұрын

@@ATOcom How to program them?

you can sent code

Thanks sir aap ek video delta servo ka upper video bana jesam servo ko 90 90 90 90 degree mai ghuman chaiye Faleminderit zotëri aap ek video delta servo ka video e sipërme bana jesam servo ko 90 90 90 90 shkallë mai ghuman chaiye Thanks sir aap ek video delta servo ka upper video bana jesam servo ko 90 90 90 90 degree mai ghuman chaiye Faleminderit zotëri aap ek video delta servo ka video e sipërme bana jesam servo ko 90 90 90

how to set parameters a half video and a useless video i will nake complete video of servo in each and every mode.

music too loud it disrupt the focus on what you doing.

@ATOcom

4 жыл бұрын

So sorry

You have no methodology of teaching. How to get to the viewers if not discuss step by step....

what is V0.01?