I have watched so many of Todd’s videos, I am so used to him using that trusty Milwaukee that he looks a bit funny using a torque wrench

@Hunterworks

3 жыл бұрын

ha

Just got one in mail yesterday, used it last night. Worked great. Was a little fun getting off. But work great.

@mitchosman4189

4 жыл бұрын

What about on a general does it go the same as 900 or so 1k?

Thanks Todd tooll worked as expected easy to use and when I double checked it was right on😀

Thanks got the transmission aligned. To get ready for the New Dura clutch you go me. Thanks for the great videos

@Hunterworks

7 ай бұрын

Good deal, thanks for the comments and you are welcome!! Todd

Thanks, Todd, very easy to follow.

Thanks for the excellent info also very nice tool

Thank you. You've put alot of great information out over the years. Ive bought your belts. And clutches. Ext. Good parts

Heed Todd's warning about not trying to push the go/no-go tool on too deeply. You won't be able to get the tool off. I had to loosen the bolts again after tightening things down and still couldn't get it off after jiggling the transmission. Had to use a 3 jaw puller. Then I went at it again but just shy of how deep Todd gets it (sounds dirty, eh) in this video and feel confident my machine is aligned properly.

@gmctech

2 жыл бұрын

Maybe i got lucky but i can slide the tool with some extra force about 1/8 of an inch past the place Todd gets it on the secondary and it pops right off with a few tugs. I did clean the shafts to a mirror finish using Wicked metal polish though before i started.

@Bizill75

2 жыл бұрын

@@gmctech Funny thing, a year later my Polaris crap Chinese bearing went out as many do so I installed the SupetATV GDP transmission and used my Hunterworks alignment tool and it worked even better on the brand new input shaft. I've lent my tool out to a friend but told him it's cheap enough that he should have his own in his tool arsenal. I'm probably going to have to move back to a regular HW belt as the thick belt creates too much heat for desert riding in the summer. More money... always more money to spend on this damn hobby.

Thanks for the video and your products. I used the go no go gauge to get rid of the clutch noise on my 2017 Polaris General 1000. It still has the ringing or cricket chip noise so 🤷

@Hunterworks

3 жыл бұрын

email me a video of it so I can hear it and tell me in there what belt and or kit you using todd@hunterworks.com

EXCELLENT TOOL... works great.

Is alignment the problem when you have to put the brake on and give it gas for it to go in gear if I don't do that if I just give it gas to go it will miss going in gear and just grind

I got a 900 xp rzr it will shreds belts if I floor it for over 10 15 seconds also it not pulling but 7200 rpms I'm wondrring if it maybe out of alighnment I know inside the secondary everytime I pull it off the splined inside is shoved over to the side..

Great video

thanks for info

Ordered my tool today. I got 1200 miles out of my stock belt (that I now carry as a spare), then another 200 out of the new belt before busting the transmission. Put the new transmission in and got 20 miles before the belt shredded. Definitely out of alignment.

@Hunterworks

3 жыл бұрын

Maybe, could be several things though

How often should you check alignment? I'm big on maintenance, some would agree and disagree but I also greese wheel bearings every 300-400 miles with green greese. Is this about right for alignment check?

@Hunterworks

2 жыл бұрын

I would not unless there was an issue popping up but if you up for it, as often as you like but 300-400 miles seems often if you putting a lot of miles on it.

Question: do you ever have to “shim” a primary or secondary clutch to line them up side to side let’s say? I have a duraclutch and I cleaned it up nicely and the belt still spins when in neutral. I have another clutch setup with a tied secondary and weights and whatever that doesn’t cause problems when putting into gear because of belt spinning. Yet to check alignment on the 2021 900 trail Polaris. Neither clutch has much use. I like the duraclutch for winter time for plowing etc. only time I use it. ‘

@Hunterworks

Жыл бұрын

What vehicles?

@tim2truk162

Жыл бұрын

@@Hunterworks 2021 Polaris rzr trail 900. Have put it on its side a couple times so it may be alignment?

@Hunterworks

Жыл бұрын

@@tim2truk162 Then I suggest getting our alignment tool first and check it and/or fix it

does an 1/8th of an inch make a big difference? i did my alignment about 30 hours ago but now im barely off again, could that be why its hard to shift? because my one way bearing is fine and i cleaned my clutches and everything seems to be in spec.

@Hunterworks

3 жыл бұрын

Yes a 1/8 is huge like have a belt 1/4" longer or shorter. But that is not causing this, either alignment, bad bearing or clutch not opening. We have a video on this too, one of the newer ones

@Hunterworks

3 жыл бұрын

kzread.info/dash/bejne/nK5po6qzYruTadI.html

A friend of mine recently had the turf mode delete done at the Polaris dealer. He's had a smashing and clunking clutch on take off since new. After turf mode delete was done it was no different so we bought the alignment tool and i was aghast with how far off it was having just been to the deaer. My question is, does the dealer not have access to a factory alignment tool, or does Polaris just bolt it together and hope for the best?

@Hunterworks

2 жыл бұрын

They probably just bolt together and do not know it should be aligned and polaris does not have an alignment tool, only a flat bar for spacing

@gmctech

2 жыл бұрын

Many thanks for the reply and info! As a side note the dealer severely over torqued the 6 bolts... Love your alignment tool, just the quality of the precision tool makes it a great deal! As always a pleasure doing business with you great folks.. Take care and i think my next purchase will be some gear butter 😎

@Hunterworks

2 жыл бұрын

@@gmctech Thanks

I see nothing for a Turbo, is that in the makes?

@Hunterworks

3 жыл бұрын

Yes

My crank shaft and transmission shaft are within .002 of being parallel, but the belt is still riding to far to the driver's side. I need to move the transmission towards the passenger side, do the transmission brackets move from side too side for more adjustment

@Hunterworks

Жыл бұрын

How are you measuring? Your not moving your twisting. If you use our tool that will be correct the issue still there then the issue is one of the clutches

@ronyoung6054

Жыл бұрын

@@Hunterworks I am measuring with dial indicators for parallel on shafts, but the trans is still to far to the driver's side. Been this way since new, 10k miles with alont of troubles since new. No dealer help. I own a shop and build race cars for a living, now going to the aftermarket for help. I have bought 3 primary clutch tool removers on the internet and yours is the only one that worked. I bought an alignment tool from another internet place and it doesn't fit my shafts and they won't respond to me on eBay. That is before I seen your site, I am ready to make new brackets that work unless you guys have something better. I realize it's not rocket science but use it every day and polaris could care less

@ronyoung6054

Жыл бұрын

And thank you for your help

@Hunterworks

Жыл бұрын

@@ronyoung6054 sounds simple compared to your methods but not sure how you getting the parallel on crank. Our tool is crazy accurate. Find it on the site and watch video. Also your movable sheave might be in too far.

@ronyoung6054

Жыл бұрын

@Hunterworks Inc. thank you, my belt is riding on the outside of the primary clutch which indicates to me that the trans is out to far from to the driver's side. I made a tool that goes on both shafts to check the shafts parallel. But in and out is the problem. Dealer aligned it and said that it's perfect, but will stall in gear when stopping. Not trying to contradict you. I've watched your videos, I'll watch again

Will this with for a 2015 900s?

@Hunterworks

3 жыл бұрын

No but our new tool will, approved it Friday, getting them made now, so 2-3 weeks we will have it

then are you shipping to europe again?

@Hunterworks

3 жыл бұрын

Sorry we are not

😮

Why doesn't anybody seem to check offset on these machines? It's a critical factor!!!

@Hunterworks

3 сағат бұрын

What is offset to you? If you mean alignment left and right, it can't be off like offset, just parallelism as I call it. The way they mount on the vehicles these tools are used on it can't be off like that, just twisted if you will. We have a video on this to explain it

@andrewbibeau231

3 сағат бұрын

@@Hunterworks you put the secondary clutch on the shaft and align the stationary sheaves which on the drive clutch is the inner and secondary it's the outer sheave. This done typically with an alignment bar on the snowmobiles which is typically also used to determine alignment. If the secondary clutch is too far inboard you add shims to a measurement of 5/8" on sleds or when the alignment bar is just touching the back of the secondary sheave P 90 is a different number but regardless clutch offset is a factor in alignment and no one seems to mention it in any of these videos.

@andrewbibeau231

3 сағат бұрын

Can't is a strong word.

@Hunterworks

2 сағат бұрын

@@andrewbibeau231 That is because that is not applicable to these vehicles, can't is the correct word. You tell me how it can be offset, what would cause that ?

@Hunterworks

2 сағат бұрын

@@andrewbibeau231 Also, some of these UTV's use shims and you shim the secondary to have the belt in the middle of the primary or close to it. However the shafts themselves can't be moved left to right.