Literally the best timing video for d series on KZread great camera work and commentary even years later. Thank you

Thank you. I'm planning on buying a cheap old timing light to use on my cars and every video I've seen uses a fancy adjustable light procedure. I just needed a video showing a normal procedure with a cheap timing light and this video was exactly that.

This is the easiest and best timing video I've ever seen. Thank you

@jaymartin7119

2 жыл бұрын

Jenna are you not letting ted in

Awesome video man. Love to see a clean del sol.

This video was awesome! Thanks 🙏

Good video. It’s a lot easier with the tire off and extensions for the crankshaft pulley.

@yebo3061

3 жыл бұрын

True, but I could reach it pretty easily!

Great video!

Don't forget to ensure the vehicle is warm by holding 3k rpm until fans come on. Then check timing

@isaiahramirez1864

2 жыл бұрын

why does engine have to be hot for timing check?

@chrisoliveira6941

2 жыл бұрын

@@isaiahramirez1864 not sure exactly but it's stated in service manual.

@wokevroz

Жыл бұрын

@@isaiahramirez1864 so the rpm’s can drop i think

@aterpay1826

Жыл бұрын

@@isaiahramirez1864 need to make sure the Car ECU is not using the cold engine map and it’s running at normal temp

I'm curious about the d16 y7 is it the same as the demestion you just showed

A+ young man

Great video man!!! I have one question before I do all this do I have to have cylinder one all the way up or just do this process just ass you show it?

@kidnextdxxr

2 жыл бұрын

With the crank lined up it should b at top dead center

what will happen if you turn the CAM SHAFT GEAR counterclockwise instead of the CRANK SHAFT?

How can you have 2 marks one for distributor and one for top dead center f23a1 engine Honda accord lx

Does the service port apply to my 89 Ef DX d15b2?

I changed my belt and my timing marks line up at tdc but i didnt adjust the ignition timing afterward since it was never mentioned in anything i read or any videos i watched, would that cause a misfire once it starts to warm up?

@yebo3061

3 жыл бұрын

It sounds more like an ignition coil to me, I've had plenty of those go bad. Does it hesitate occasionally when load is put on the engine?

@skoomacat13

3 жыл бұрын

@@yebo3061 i actually have new ignition coil in there. I didnt have any issues until i changed the belt. It ran fine for a few minutes until it started to warm up and the rpms started jumping.

@yebo3061

3 жыл бұрын

@@skoomacat13 if you don't have an ignition light you can just loosen the bolts and turn the distributor. I believe I had the same issue with this del sol, and advanced timing helped. (higher rpm)

can you set the ignition timing without using a timing light?

Does this work for a D17?

My timing cover doesn’t have the little hole to loosen the tensioner is there another way?

@hadrianaugustus3547

3 жыл бұрын

There’s a plastic cap over the hole

Is a D15B1 a interference engine? I think my timing belt may have slipped. Thanks 👍

@wtang912

2 жыл бұрын

From google I found all Honda engines are interference except the 3.0L and 3.2L

@M3GAN3116

2 жыл бұрын

@@wtang912 Thanks 👍

You rotated the engine counter clockwise twice?

@yebo3061

4 жыл бұрын

christian dayrit as long as the timing marks are correct you will be fine. You’ll want to make sure the single line crank pulley) is at the timing mark. Yes you want to turn counter clockwise. You can message me if you have any more questions

@kaseone6896

4 жыл бұрын

Ty.. I set the timing marks and car just cranks.. do you have a way I can contact you other than this KZread?

Will the timing make the car not start

@ahunt

4 жыл бұрын

Turns over, but doesn't start? Yes its possible, especially if it's been messed with, but it would still usually spit and sputter or try to start even with the wrong timing. If it isn't attempting to start at all go back to the basics first, make sure its getting spark, and fuel.

@SalvageCivics

3 жыл бұрын

Try swapping around iat & iacv plugs?? You might have them crossed..

Does this work on a y8 non vtec with no marks? I'm doing a head gasket replacement and wanna make sure when everything goes back together there isn't any issues. Also how can you do the ignition bit without that tool?

I have a D15B7 Del Sol. Anyway to make it a little faster, more HP's... Like put a Different Header on it like a Vtech Head. I watched a video where this guy says he did that to his Engine.

BRO i cant find these crank marks on my D15B2 in my 1991 Base model CRX plz help! are they under the belts? they dont appear to be in this video :(

@rendiix4269

3 жыл бұрын

They are just on the side try to clean the pulley