Share your experience with stop leak good or bad.

@brokenlee5922

4 жыл бұрын

did you consider that mabey didnt work cause the water wasnt hot

@AMG28ful

4 жыл бұрын

@@brokenlee5922 no need.... those holes are too big. Stop leak is made for cracks or leaking gaskets... those are under 1mm

@ALSHAHRANII

4 жыл бұрын

@@brokenlee5922 that's right the water must be hot to make the seal cure

@elmutide

3 жыл бұрын

The Bar's gunked up my thermostat which took some diagnosing to find. Won't go down that road again.

@NATESINTERACTIVEAUTO

3 жыл бұрын

@@brokenlee5922 I heated it as I show in other videos

That’s a lot to expect a stop leak product to fill a hole that size. Good grief that wasn’t even a fair test, plus the fact the coolant is supposed to be hot. I would say the test is a failure, not the stop leak.

1. recommended for holes less than 0.8mm (0.032 of an inch) 2. Heat is required to activate the silicates & drive moisture from them, thus leaving the crystals that will plug the hole/crack.

Hole way too big for stop leak to fix, and think about it, if it could stop such a massive leak, it would also clog up your cooling system, the radiator and heater core have small narrow tubes.

Might work if you clamp the hole mostly shut first so it can build up there. Also as other people have said it needs to be heated.

It needs to be at least 150 to 200 degrees to work!! It well never going to work with cold water lol

@NATESINTERACTIVEAUTO

3 жыл бұрын

Its heated as I have shown in other videos

@rramirez115

3 жыл бұрын

Exactly

@rramirez115

3 жыл бұрын

@@NATESINTERACTIVEAUTO , it is NOT HEATED at 200 Degrees F, your experiment is totally misleading,I don’t see any steam coming from the leak, therefore YOUR DEMOSTRACIÓN is INACCURATE..!

@wendykalman9975

2 жыл бұрын

If you have a leak that big just put a damn plug in it 😆

@mohdrusdimohdmokhtar4158

2 жыл бұрын

I also think so... It need heat to work...the heat will make the sealing work....

it works i got stuck in the middle of the road put two bottles in and boom drove 1200miles south and it still ran for 2 more years

I feel like these products are mainly used for when the plastic lids start leaking very slightly , But yeah, this needs to be in a car engine at operational temps 180-210º under pressure and going.

@jenniferprendergast9074

Жыл бұрын

My coolant radiator thermostat keeps going to the middle fast

And the leak flows happily ever after~~

Nice experiment but don't forget to read the inductions. Your next try should include a way to heat the coolant to the correct temperature and use a realistic leak.

@VIKTORSCHAUBERGERscammersONyt

2 жыл бұрын

The accent should clear up anyone who thought he read the directions and used it properly.

@fakeaccount8342

Жыл бұрын

Radiators get bullet holes... 🤣

Great product I have used it for the inner heater radiator and does the work perfectly.

@kimberlywright4988

5 ай бұрын

Hi can you tell me about the leak in the anti freeze container and the hose connected to it

@ShakarAhmadi

5 ай бұрын

@@kimberlywright4988 which one, in or out? This product does not work with rubber hoses, only with aluminum pipes. Please make your question clearer so that I can be helpful.

In the time it takes to do this you can replace the radiator or a hose with the hole in it. Radiators are not hard to replace, they seem intimidating to people but they're very easy to install. You literally remove the hose & few bolts & lift, then put new radiator in & reattach hoses & done. Make sure you flush radiator with a cleaner before you add coolant, so you catch any debris that was inside radiator during shipping & then after it's flushed & clean, add coolant & done.

@koglioknows

2 жыл бұрын

That used to be the case, but most of your newer cars and especially some foreign models today, its not at all easy to remove radiators, sometimes half the front end needs removed, or they can also come out the bottom of the car, not to mention some models need special tools to remove oil lines from them too. FYI 😎👍

It wasn't meant to plug a cold garden hose . Used this exact stuff in my 2003 Ford Explorer 4.0 coolant radiator. Had a leak that would start when it got to about 5 psi , or 150 degrees . Right were the plastic tank is crimped to the aluminum radiator. It worked well for two months when I replaced the radiator . It even flushed out without leaving residue in the engine. One of the few truly safe and effective products for this very common type of leak . Just about every company that produces additives like this has a similar product . Heat , pressure , small leaks. Read the bottle 🤦

In my opinion this is an accurate display of most stop leaks, they don't permanently fix radiator problems , and should only be used in emergencies.

I think you should give it longer off-time in order to let the material accumulate in the cracks

would that work just for the radiator?... cause maybe I have the leak in a unreachable part of the hose

Can't wait to try it with Barr's stop leak.

Ok this explains why it didn't work on a leaking kitchen cold water pipe... But after a few glasses of water i never pissed again.

This stuff works. I had a leak in My civics radiator and I added the silver aluminum mix and presto! It’s genius. I have a new radiator in the mail but I’m not installing it until the radiator starts leaking again. Probably not the best idea though. Edit: use the silver stuff! It’s better and it’s also under 10$

@ila83

2 жыл бұрын

What did u due in your process of putting it in ?

@demo1762

2 жыл бұрын

Hi, did the radiator start leaking again?

@MrSatchelpack

2 жыл бұрын

I don't doubt that it probably worked, but these particles seem really bad for the pump.

@JohnJohn-zn8ib

Жыл бұрын

@@ila83 probably didn’t do it.

I'm a little confused by everyone's comments about how the coolant needs to be hot to work. I just bought some for my radiator, it says right on the bottle that it should be poured in a cool radiator, so that's what I did. I also used ice cold well water from my hose as coolant and it stopped the leak within a couple of minutes and it was a pretty decent leak. My guess is that they tell you to put it in a cool radiator for safety and then it won't start working until the heat and pressure builds up?

@bigd4136

Жыл бұрын

That’s exactly right. Taking the cap off of a hot radiator is really dangerous. Pour it in cold, drive or let it run the proper amount of time to heat it up. I’ve used it in my youth when car fixes were not priority and it worked great. Honestly probably longer than it should have.

I thought the coolant has to be heated up for this to work? It works fine on the car that I am using. It just a temporary fix to get you by. The Bar Leak last for 8 months before I had to reapply.

All the hoopdies ive owned it always worked good...there is no way he heated it up enough..also those are pretty serious leaks

I used a radiator stop leak before. It worked the first shot. I was impressed. Although my head gasket was blown too... 2000 Cadillac Eldorado 😂

@vivillager

4 жыл бұрын

My dad's car was a Cadillac Eldorado, he loved that car. He can't drive anymore, so he gave it to my older brother with about 80k miles on the odometer. It didn't even last a year before it was sold for scrap. Anyways, I bought a car with stop leak in it, and didn't know. It was a 2002 Chevy Impala, which are notorious for blowing intake gaskets. Instead of replacing the intake gasket, the guy that sold it to me put stop leak in it. The heater core and radiator could clog about once a year for a few years, then it would clog just once every 2 or 3 years. Finally from years of intermittent overheating, it blew the heads. I got a set of heads from a junk yard for $50, and while I had the engine part I used a pressure washer to force out everything that was still in the water jackets, plus I replaced the hard lines, heater core, radiator, rubber hoses, and water pump, and it never clogged or overheated again. It was funny for a while because the heater core would start to clog, and if I floored it and got the RPM really high, you could hear this gush of water from under the dash, it would sound like someone flushing a toilet and then I would have heat for a minute or two, and then it would go away so I would have to repeat.

@abairgoodman8045

4 жыл бұрын

John Davis you should have done a back flush on it and put some rust removing stuff inside of it to get rid of some stuff that might be clogging it. Then tried to burp the system cuz every time u replace a cooling system part you should because that allows air to get in that’s what the flood of coolant under the dash was you heard. I’m currently struggling with the overheating shit and researching all these videos. Since it’s a closed system there shouldn’t be air in it I replaced the thermostat and Ik that it didn’t get burped so hopefully it fixes my issue but there may be a leak somewhere only one way to find out if. In a few hours when places open up I’m going to buy all this stuff I need I hope it works😂😂

@jquerciaproductions3660

4 жыл бұрын

I have a 1992 Cadillac Eldorado it has a slow leakage but it’s fine just keep filling it up with antifreeze and this product in the video above doesn’t work at all I used it on my 1996 Ford Taurus and it messed up my car badly

Does this stuff also stop a small leak in the water pump as well??

Id like to see you do this with Holts Radweld (Subaru coolant conditioner in usa)

Can this be used for carbon steel pipe? And process with 180 degrees

Mine is leaking out of a freeze plug .. will that help out my situation? Working with a 2011 grand marquis

How about a 303 aerospace on rubber vs no treatment

You let it run for 1 minute, 20 seconds and then thought it didn't work. When it literally says on the bottle to wait at least 15-30 minutes at an idle. Of course it's not gonna work after less than 1.5 minutes.

Worked for me today on a 2000 Nissan Xterra water pump leak.

It works well for me and save me tons of money

@teoquero3628

3 жыл бұрын

Really, I need one of those ASAP

@sonnyesqueda1284

3 жыл бұрын

Does it matter how big the Crack or hole is?

@rynechristesen2392

3 жыл бұрын

@@sonnyesqueda1284 I believe it does.. this is something I’m doing to my car with a very slow drip leak from cracked radiator tubes due to a bottoming out. I don’t think anything would work against a steady flow leak like this.

4 plus gallons of water/coolant, 1 hole bottle of stop leak and still it leaked like a sieve. the original hole was huge (pencil lead diameter) maybe that had a lot to do with it.

@cb250nighthawk3

3 жыл бұрын

I believe you're right. Bars worked to stop the leaks in my car's radiator. Probably 1mm holes. 😁

@wendykalman9975

2 жыл бұрын

With a hole that big just plug it . Or use a piece of rolled up duct tape. The metal foil kind . I actually did that and it worked for 200 miles 🤓

I used it in a 20yrs old Volvo and it lasted for THREE years

If that were a car radiator, you'd have one hell of a leak.

It works better when it in an actual radiator with heat.. it works on small holes but big ones like that not so much.

As many have said, you missed a very crucial part of cooling an engine… the heat. You need to let the engine idle at operating temp for at least 15 minutes to allow for the formula to expand and work. There is a video of someone doing the same experiment, but they used a heating system to gradually increase the temp of the coolant… and voila it actually worked to stop the few leaks on the radiator.

Dont you have to use hot water or antifreeze I thought that stuff worked when the engine got hot

@NATESINTERACTIVEAUTO

5 жыл бұрын

I did heat the water at one point but during the video the thermostat worked loose.

So is the thermostat sensitive to this stuff ?

I used K-Seal on my car several years ago. The car has not had a coolant leak since.

was the coolant over 105 degree. if it was heated to 105 or higher it mite work faster. not 100 present sure if this is true. (110 % it's true)

if it works then the outlet of the radiator will be seal as well

Man if i have a leak that bad im not using stop leak. I think its better for the pin leaks and ones where you can smell it but cant see it but some residue.

Honestly if you got a leak pouring out that bad you got to give it up ans go to the mechanic and get new radiator. But sometimes it does take a few bottles to stop it or extremely slow it down

That wasn’t a leak more like a Continuous squirt

@NATESINTERACTIVEAUTO

4 жыл бұрын

Yes it was bad check all the stop leak videos to see what works best.

@mikehause6585

3 жыл бұрын

That's just a hose fitting with no hose attached 😅

Ya I was thinking same. There’s no heat to make a reaction

It needs heat to cure

My car engine had a one little hole like 1mm in the freeze plug, used Abro powder stop leak and it fixed the leak for long period till freeze plugs replaced.

It Hass to be like boiling temperature for the stuff to be working. Like they have a new brand with actual pellets In it, oh they are solid but when you pour them in the boiling coolant they dissolve and act like a JB Weld through your system. You can’t use cold water lol

Major problem with your test is radiator systems are under pressure ... usually around 10 or 15 pounds. Your experiment was not a closed pressurized heated system.

If you have a leak like this one dont use that , just replace the part , this is just for small leaks

Meaning ??? Maybe its work in hot water only ?? 🤔🤔🤔

On the label run car until hot where is the engine ?

It looked like you're pouring in some pretty nasty looking coolant. Maybe just full of the stop leak. I do realize that coolant system leaks can be expensive depending on the circumstance. But I also assume that stop leak could cause more damage than good in the long run.

@Blazeww

Жыл бұрын

There's people that put in stop leak and years later it holds. Tho if your engines to far gone it most likely won't work at all and you know it's a much bigger issue that needs proper repairs.

it also stops your Radiator from working.

@Sobriety5424

4 жыл бұрын

Steffen I’ve seen it go both ways.

@DrFillyBlunt

4 жыл бұрын

You see Ivan, if clog radiator up to point where no flow, radiator cannot leak.

@rokitman5753

3 жыл бұрын

No Steffen it actually works theres alota science in most products

isnt it supposed to be heated?

Nice

How many hours? There would be a huge puddle or trails as you drive, I would say fail

That stuffs meant to swell up old rubber o rings and gaskets not holes lol

This stop leak is supposed to be added to a cold radiator and needs to be heated to work properly. Testing it with cold fluid isn't the best test. And it also needs to cool down e.g. 48 hours to cure around the hole or crack. To make sure this stop leak works properly, remember to use with new clean fluids. Do not put it in old/dirty coolant. Hope this helps some people

You plugged the radiator up. Look at your return hose there was no flow. Your stop leak plugged off the port so it couldn't plug last hose pressure to great.

Had a hole in my radiator the size of a dime. This stopleak sealed it in 4 mins with the engine running i used 1 bottle i. 4 gallons of 50/50

@sonnyesqueda1284

3 жыл бұрын

Do you really recommend it.

Engine gotta be at running temperature

Why does the bottle say make sure engine is cold

The coolant need to circlelate around for it to work

I’ve always just opened the lid and pored it in

i would have stopped and started the pump so it could bond.... seems like the continues squirt stopped it from sealing..... if you had a cut on your hand after a few mins it would stop, if it was squirting out you'd goto AandE... lol

Please test mannol products

your dad said water the lawn! not antifreeze it...DAMN MAN!

Kseal

How to plug your heater core for only 10.99 😂

I think the test hole was too big. If it works at all, it would be for smaller holes. But kudos for trying to test it.

@NATESINTERACTIVEAUTO

4 жыл бұрын

Yes i totally agree. How can we improve?

@blueyedboymrdeath

4 жыл бұрын

@@NATESINTERACTIVEAUTO Test with a much smaller hole. Say, one that leaks 1 gal / hr. while pumping. That might be more typical for many leaks. Fast enough to overheat your car pretty soon, but not that fast.

Needs heat to heat chemical. Then it hardens when it touches oxygen. Fun video though thanks!

The eater need to be hot like the radiator for the sealant to work, it needs heat to activate

@NATESINTERACTIVEAUTO

4 жыл бұрын

I heat it and show in videos, what can we try next?

Does anyone know if you can use Bars Stop Leak multiple times? It was applied to my vehicle and it stopped the white smoke immediately…. However that lasted a few hundred miles and now the white smoke started to return. I just need the get the car up and running for another week so I can get it in the shop for repair. Thanks I’m advance to anyone who can help with this question!

@manz7860

2 жыл бұрын

Drain the radiator(or wait for fluid level get low I guess) and just repeat the process Hope your rides OK

That fling hole is like a dime size hole you serious ...

Hey, I don’t mean to be that guy but where’s the coolant going?

How to plug coolant passages, destroy heater core and cause severe internal failures should be name

I'm guessing it's not being recycled.

Only thing stopping that leak is pouring concrete in your radiator

WTF DID I JUST WATCH LMAO

did it work?? is the radiator still leaking...?

where was the heat????

Xenum Restop radiator anti-leak works much better.

@NATESINTERACTIVEAUTO

5 жыл бұрын

I would like to try it.

It doesn't fix stuff but it WILL get you through to a part store

I put a bit of stop leak mixed with coolant in the coolant reservoir/over flow, although I did put most of it in the radiator. Should I be worried that I put some in the reservoir?

Its gottta get hot. Then cure

It needs to be hot.

U need heat only then compound will work

Well 2 things.. the highest the pressure gets in a cooling system is around what 15-20psi.. i dunno what pressure that pump you used could generate but still the colling system gets hot as fuck.. maybe if you heated up the whole system because some of that stuff activates with heat and pressure. Some reacts with heat differential like its all fluid while cool or hot but when it goes from hot to a cool place like through a hole, the stuff hardens and collects at the hole…

If this stuff could stop a leak that sized, it would also plug up those little tubes you have. I'm just trying to see this stuff get fuzzy like what's coming out of my buddy's radiator after using this stuff. It looks like an animal died inside the rad!

The coolant wasn't hot operates it

You are the dimmest bulb in the chandelier my man

That hole seems to be way too big for any stop leak of any kind to work.

Just waisting antifreeze just use Water pluss the sealer activates when its hot

Auto repair shop trying to instill no confidence in stop leak products, simple as lmao

Should definitely just fix the leak and not gum up your cooling system

That is a big hole!

Nice set up....but.....no heat isn't gonna work.....

That will not work .. test it in a car not no tubes look how much he have to use to even see just save your money and get k seal coolant permanent repair or just get it fix

Not only did it not get heated.. Was that oatmeal at the end? 😆.. Or what drained and reclaimed? That doesn't happen in the real world. It would also be nice to see everything going on.. Not just a staged area. Wow..