Thanks for reply , if we’re just concentrating on the tooth not the rake , he’s doing bottom as well assuming because new chain , just doing tooth can you sharpen pushing and pulling or not?
@LugasLife2 ай бұрын
Thank you for video, good work and very sharp! 👍
@Deano0342 ай бұрын
“Push too hard will ruin your file” Pretty sure dragging your file backwards will ruin it quicker than pushing too hard.
@JakePlisskin12
12 күн бұрын
Not trying to slep on any toes or offend anyone but pretty sure the "you'll ruin your file by filing or dragging your file backwards" is a myth.
@Gary672424 ай бұрын
enjoyed the video...thumbs up !!
@sdc03864 ай бұрын
Nice work 👍
@JohnnyButtercuts4 ай бұрын
I have found that unless you have only been using that chain for 15 minutes, you will be using more than 3-5 strokes per tooth 😂. I typically use 10-20 light pushes to get that perfect edge along the entire tooth and remove all the burrs. It’s easy to get carried away and over sharpen some teeth shorter than the others. Overall, you truly do not need it to be perfect because as soon as it hits bark, the teeth are getting beat up. Just get the edge back so it’s not harder on your saw to get through the cut
@robynmcdonald39424 ай бұрын
Well, everyone has an opinion. If it gets sharp, you did it right.
@luxbeci23 ай бұрын
I have Stihl 880 How need sharpening?
@Wood_Slice2 күн бұрын
Lets say you slab a 42” by 10 foot long red oak log with a granberg ripping chain and no obstruction such as nails. After how many slabs do you recommend sharpening the chain
@Ecksterphono4 ай бұрын
Question. I need a chain for my Husqvarna 455 rancher. 20 inch bar 72 tooth 3/8th pitch. The H40 Husqvarna chain is horrible and I need an upgrade. What is the Stihl equivalent or Oregon equivalent part number for that chain? . I'm getting conflicting results from different sources. I hate the out of the box Husqvarna chains they put on these bars, they don't sharpen really well either. Need a good chain for felling and bucking. Sometimes I wish I had my own chain cutter and tools which I used to have and cut my own.
@chib9427
4 ай бұрын
You have the tooth count and the pitch now you just need the driver gauge. (.050,.058, or .063) huskies usually have 0.58 if stock bar is used.
@Ecksterphono
4 ай бұрын
@chib9427 .O50 says it right on the bar close to the bumper spikes.
@PortedSaws
4 ай бұрын
On a stock 455 i like to put .325 chains But that's just my opinion
@Ecksterphono
4 ай бұрын
@PortedSaws Thanks. That what I was thinking. Awesome video.
@thomashocker2792
4 ай бұрын
7 32nd
@chrismarjerison67913 ай бұрын
Dope
@voronezhpokos4 ай бұрын
Лучше точить на станке, напильник для правки
@luxbeci23 ай бұрын
Which Chainshaw this? Stihl 361?
@PortedSaws
3 ай бұрын
Its 3/8s chain
@rooster30195 ай бұрын
I think your file is larger in diameter than what Stihl intended.
@PortedSaws
5 ай бұрын
Yes stihl recomends 13/64 but i like 7/32
@rooster3019
5 ай бұрын
@@PortedSaws I use the smaller file when the teeth are more than half worn; if I think about it....
@teresahicks4812
4 ай бұрын
😅
@bradmckay7881
3 ай бұрын
😂 stay away frm my saw
@Vanmoof55 ай бұрын
Hi sharpening with file is new to me , I assumed you only pushed file and retuned not touching tooth assuming you sharpen only one way ?
@lbnoronha
5 ай бұрын
It looks one way but i believe he is sharpening when he pulls the file not when he pushes it.
@MrSprintcat
5 ай бұрын
No, it sharpens when he is pushing.
@PortedSaws
5 ай бұрын
Yes sorry i didnt tell ya but yes when you push the file thats when it removes Material
@MrSprintcat5 ай бұрын
Sthil recommends 5.5 mm/ 13/64, file.? 😊
@PortedSaws
4 ай бұрын
Yes but 7/32 is what i like
@gunterbecker8528
4 ай бұрын
I've learned something very valuable just now,so thank you!
@milanbiskup5755
4 ай бұрын
13/64 is 5.2mm but 7/32 is better
@REDLINERUNNER4 ай бұрын
Easy, just buy 2 in 1 Stihl chain sharpener and thank me later. I have demonstration on my channel.
@patterdalezipsuzilil4 ай бұрын
File only works one way so whe you drag it back your making it blunt again 😂
@kirkchatwin6160
2 ай бұрын
You for real can’t see the file lift? Ffs
@Lars_Olsen
Ай бұрын
Watching the video like this 🫣
@JakePlisskin12
12 күн бұрын
Thats a myth bub. Get taught.
@JakePlisskin12
12 күн бұрын
I don't understand how filing back words would make the edge you filed forwards blunt. How? If anything the back file would polish the rough forward file push.
@SekarS-qv1qk4 ай бұрын
Your ஃபால்ஸ் chain சஸ்பெண்ட் g
@patterdalezipsuzilil4 ай бұрын
File too big your not ment yo file the link
@JakePlisskin12
12 күн бұрын
None of what you said is true. Get the gullet bub
@mencheaustria3 ай бұрын
to much continuing by sharpening of chain was destroyed quickly
@JakePlisskin12
12 күн бұрын
Is this comment in English?
@yashasony84064 ай бұрын
This sharp not long time kating my 5 year experience
@paulstokes18314 ай бұрын
I see that you know how to dull a file! Everyone knows not to pull a file backwards.
@DaleRayJr
4 ай бұрын
Dull a file? 😂 1-2 chains a file and said file goes to a trash can.
@dope7kids
3 ай бұрын
Your right, and why is he sharpening a new chain?
@paulstokes1831
3 ай бұрын
Another scam channel on KZread
@allen4758
Ай бұрын
After 28yeàrs in machine shops, I can't tell any difference from lifting the file compared to dragging it back, except it's easier to drag
@jonathancristobal4724
18 күн бұрын
I love comments
@user-lx3li6px1v4 ай бұрын
Неправильно! Напильник должен двигаться на зуб, а не от него!
@laszlosoos4093
4 ай бұрын
😢
@user-vc4hc7mi7h
4 ай бұрын
Все верно, напильники во всем мире работают в одном направлении - "ОТ СЕБЯ".... Они так устроены....... 😊
@user-lx3li6px1v
4 ай бұрын
@@user-vc4hc7mi7h Я про другое говорил! Заусенец от напильника наружу выходит, когда точат как в ролике! Что бы его не было, нужно напильник вести на зуб, и как ты скажешь - от себя
@steppoffaith84264 ай бұрын
Clueless
@sascha30882 ай бұрын
Badest i‘ve ever ssen
@user-ez3mf3ps4x2 ай бұрын
Hattapus://youtu.b/sjeswsanstvati
@darrenboston3424 ай бұрын
By the time you’ve spent doing this you might as well just bang a new chain on! Not worth taking to get sharpened as they charge more for that than a new chain!!😳 This is for people who literally have all the time in the world to spend doing such a boring job!!
@MrDavidjohn66
3 ай бұрын
I use a grinder 😂 life is to short for a file .
@JakePlisskin12
12 күн бұрын
Yeah if I was a homeowner and never used my saw unless my wife told me she wanted some branches trimmed on the Japanese maple that's blocking out the sunlight to her flower bed, I would probably agree with you. But if I actually cut trees bigger than my d!ck to like make a fire or remove a tree, I'd probably just take my file to my chain for 5 min to bring it back to razor sharp. It literally takes less time and effort just to sharpen it yourself than it does to take the thing off and take it to someone and the amount of money your spending on popping a new on when it gets dull is even worse. If it's not than your doing it wrong and you don't know what your doing or even looking at.
Пікірлер: 62
Thanks for reply , if we’re just concentrating on the tooth not the rake , he’s doing bottom as well assuming because new chain , just doing tooth can you sharpen pushing and pulling or not?
Thank you for video, good work and very sharp! 👍
“Push too hard will ruin your file” Pretty sure dragging your file backwards will ruin it quicker than pushing too hard.
@JakePlisskin12
12 күн бұрын
Not trying to slep on any toes or offend anyone but pretty sure the "you'll ruin your file by filing or dragging your file backwards" is a myth.
enjoyed the video...thumbs up !!
Nice work 👍
I have found that unless you have only been using that chain for 15 minutes, you will be using more than 3-5 strokes per tooth 😂. I typically use 10-20 light pushes to get that perfect edge along the entire tooth and remove all the burrs. It’s easy to get carried away and over sharpen some teeth shorter than the others. Overall, you truly do not need it to be perfect because as soon as it hits bark, the teeth are getting beat up. Just get the edge back so it’s not harder on your saw to get through the cut
Well, everyone has an opinion. If it gets sharp, you did it right.
I have Stihl 880 How need sharpening?
Lets say you slab a 42” by 10 foot long red oak log with a granberg ripping chain and no obstruction such as nails. After how many slabs do you recommend sharpening the chain
Question. I need a chain for my Husqvarna 455 rancher. 20 inch bar 72 tooth 3/8th pitch. The H40 Husqvarna chain is horrible and I need an upgrade. What is the Stihl equivalent or Oregon equivalent part number for that chain? . I'm getting conflicting results from different sources. I hate the out of the box Husqvarna chains they put on these bars, they don't sharpen really well either. Need a good chain for felling and bucking. Sometimes I wish I had my own chain cutter and tools which I used to have and cut my own.
@chib9427
4 ай бұрын
You have the tooth count and the pitch now you just need the driver gauge. (.050,.058, or .063) huskies usually have 0.58 if stock bar is used.
@Ecksterphono
4 ай бұрын
@chib9427 .O50 says it right on the bar close to the bumper spikes.
@PortedSaws
4 ай бұрын
On a stock 455 i like to put .325 chains But that's just my opinion
@Ecksterphono
4 ай бұрын
@PortedSaws Thanks. That what I was thinking. Awesome video.
@thomashocker2792
4 ай бұрын
7 32nd
Dope
Лучше точить на станке, напильник для правки
Which Chainshaw this? Stihl 361?
@PortedSaws
3 ай бұрын
Its 3/8s chain
I think your file is larger in diameter than what Stihl intended.
@PortedSaws
5 ай бұрын
Yes stihl recomends 13/64 but i like 7/32
@rooster3019
5 ай бұрын
@@PortedSaws I use the smaller file when the teeth are more than half worn; if I think about it....
@teresahicks4812
4 ай бұрын
😅
@bradmckay7881
3 ай бұрын
😂 stay away frm my saw
Hi sharpening with file is new to me , I assumed you only pushed file and retuned not touching tooth assuming you sharpen only one way ?
@lbnoronha
5 ай бұрын
It looks one way but i believe he is sharpening when he pulls the file not when he pushes it.
@MrSprintcat
5 ай бұрын
No, it sharpens when he is pushing.
@PortedSaws
5 ай бұрын
Yes sorry i didnt tell ya but yes when you push the file thats when it removes Material
Sthil recommends 5.5 mm/ 13/64, file.? 😊
@PortedSaws
4 ай бұрын
Yes but 7/32 is what i like
@gunterbecker8528
4 ай бұрын
I've learned something very valuable just now,so thank you!
@milanbiskup5755
4 ай бұрын
13/64 is 5.2mm but 7/32 is better
Easy, just buy 2 in 1 Stihl chain sharpener and thank me later. I have demonstration on my channel.
File only works one way so whe you drag it back your making it blunt again 😂
@kirkchatwin6160
2 ай бұрын
You for real can’t see the file lift? Ffs
@Lars_Olsen
Ай бұрын
Watching the video like this 🫣
@JakePlisskin12
12 күн бұрын
Thats a myth bub. Get taught.
@JakePlisskin12
12 күн бұрын
I don't understand how filing back words would make the edge you filed forwards blunt. How? If anything the back file would polish the rough forward file push.
Your ஃபால்ஸ் chain சஸ்பெண்ட் g
File too big your not ment yo file the link
@JakePlisskin12
12 күн бұрын
None of what you said is true. Get the gullet bub
to much continuing by sharpening of chain was destroyed quickly
@JakePlisskin12
12 күн бұрын
Is this comment in English?
This sharp not long time kating my 5 year experience
I see that you know how to dull a file! Everyone knows not to pull a file backwards.
@DaleRayJr
4 ай бұрын
Dull a file? 😂 1-2 chains a file and said file goes to a trash can.
@dope7kids
3 ай бұрын
Your right, and why is he sharpening a new chain?
@paulstokes1831
3 ай бұрын
Another scam channel on KZread
@allen4758
Ай бұрын
After 28yeàrs in machine shops, I can't tell any difference from lifting the file compared to dragging it back, except it's easier to drag
@jonathancristobal4724
18 күн бұрын
I love comments
Неправильно! Напильник должен двигаться на зуб, а не от него!
@laszlosoos4093
4 ай бұрын
😢
@user-vc4hc7mi7h
4 ай бұрын
Все верно, напильники во всем мире работают в одном направлении - "ОТ СЕБЯ".... Они так устроены....... 😊
@user-lx3li6px1v
4 ай бұрын
@@user-vc4hc7mi7h Я про другое говорил! Заусенец от напильника наружу выходит, когда точат как в ролике! Что бы его не было, нужно напильник вести на зуб, и как ты скажешь - от себя
Clueless
Badest i‘ve ever ssen
Hattapus://youtu.b/sjeswsanstvati
By the time you’ve spent doing this you might as well just bang a new chain on! Not worth taking to get sharpened as they charge more for that than a new chain!!😳 This is for people who literally have all the time in the world to spend doing such a boring job!!
@MrDavidjohn66
3 ай бұрын
I use a grinder 😂 life is to short for a file .
@JakePlisskin12
12 күн бұрын
Yeah if I was a homeowner and never used my saw unless my wife told me she wanted some branches trimmed on the Japanese maple that's blocking out the sunlight to her flower bed, I would probably agree with you. But if I actually cut trees bigger than my d!ck to like make a fire or remove a tree, I'd probably just take my file to my chain for 5 min to bring it back to razor sharp. It literally takes less time and effort just to sharpen it yourself than it does to take the thing off and take it to someone and the amount of money your spending on popping a new on when it gets dull is even worse. If it's not than your doing it wrong and you don't know what your doing or even looking at.