How To Screw Cabinet Face Frames Together
Specialty Face Frame Clamps: amzn.to/35r2XCU
Irwin Clamps: amzn.to/2Iuwhzl
My Favorite Tool: amzn.to/3NIFJuO
Drill Bits: amzn.to/3kpe0k3
Countersink Drill Bits: amzn.to/3lwhmTK
Screws I Used: amzn.to/2Iru87n
Tools We Recommend: www.amazon.com/shop/benjamins...
0:00 - How To Connect Cabinets Intro
0:49 - Drill Pilot Holes
2:56 - Install Screws
3:31 - SUBSCRIBE!!!
In this video I address these concepts:
How to connect cabinets together.
What screws for screwing cabinets together?
Cabinet face frame alignment.
Thanks for watching and subscribing! As an Amazon affiliate I earn from qualifying purchases. Thank you for your support!
Was this video helpful to you? Send a tip:www.paypal.me/bensahlstrom
Become a Patron: / bensahlstrom
Blessings from Minnesota!
Ben
Пікірлер: 39
I'm doing cabinets in my new kitchen in a few weeks! This couldn't have come at a better time!
Clear and concise. Nicely done, Ben!
Nice cabinets. Hanging cabinets is where the fun is. Especially by yourself....
@BenjaminSahlstrom
3 жыл бұрын
Agreed! Been there done that!
@JTMarlin8
2 жыл бұрын
Two words: french cleat.
@scottslotterbeck3796
Жыл бұрын
Put a cleat to rest cabinets on. Of course, take doors off. Level it, get a 1x2 that is perfectly level. Rent a laser level.
Good job buddy 👍👌✌️ I love to work with wood..I made all of my kitchen cabinets out of cedar .
Thanks Benji! Great Video and Bonus tip at the end!
Thank you. Your content is always fantastic!
@BenjaminSahlstrom
3 жыл бұрын
Thanks!
Right to the point, very well explained. Thank you.
@BenjaminSahlstrom
8 ай бұрын
Glad it was helpful!
Ol Benjamin is a pretty fart smeller, I mean a pretty smart feller 😁 I have been watching him for some time and I have to say I'm pretty proud of the things he has taken on and accomplished!🇺🇲
Seems so simple, but recommendations/suggestions on a 12" wall cabinet.where even my smallest drill wont fit? I have hung 4 15" cabinets nicely, then a 12" but i put a 1 7/8 spacer ip to the wall and split out the back of the spacer because I started my pilot hole on such an angle
Why not use a pilot bit with a countersink attached? It would make the job a lot simpler...
@zanderesp4295
Жыл бұрын
Which set do you recommend?
@scottslotterbeck3796
Жыл бұрын
@@zanderesp4295 he uses an 1/8 bit
Big box stores sell screws with tiny heads
Always locked the frames in first them used did final shim. Most box cabinets are not square.
Or buy the right tool to counter sink so all screws are at the same depth...cpunter sink drill bit is on a few bucks
@BenjaminSahlstrom
8 ай бұрын
Good advice.
Hey Benjamin we missed you bro when I you going to give us another electrician video we counted on you sir
May I ask if my carpenter didn't really fixy 2 cabinet together and everything in the kitchen are done. What I could use to fill the gap in between? I hate it that ants could travel through it.
@Grunt300z
2 жыл бұрын
You need to call him back and tell him to do it right or give you your money back.
2:22 pucker factor 11/10
My question is if the face frames have a slite over hang on each side won't the cabinet require a shim at the back to level the sides,why doesn't' he mention this,seems this is just as important if not more so and how do you get that shim at the back lower side of the two cabinets.,why do all of these guys recommend an over hang on face frames in the first place.
Why in the hell would you use duck screws on cabinets a Box of a 100 is only $7
excuse me the led lights are flashing to turn on
Youre using a screw designed to counter sink itself, confused on why you drilled the counter sink.
@StanSwan
3 жыл бұрын
Designed to counter dink in soft wood not hardwood like the frames. They would split.
@ClumsyCars
3 жыл бұрын
@@StanSwan not very often. Usually you have to hit a knot.
@donnykrocks
Жыл бұрын
@@ClumsyCars It only takes a few seconds to drill a countersink, it sucks when the project is almost done and you have to start over because it cracked the face frame. It's only happened to me once but that's one time too many.
First!
Use pony clamps instead of hand clamps. Use EZ-Level system instead of shims. You’re welcome.
@Jack-gu7rr
4 ай бұрын
Agree!