How to retrofit or install a window vent, trickle vent to a upvc window to help with condensation
Тәжірибелік нұсқаулар және стиль
Hi, in this video tutorial I show one way of retrofitting a window vent to a upvc window if you are having issues with condensation or I'ts just an upgrade you want to do.
The profile I'm working on may vary from what you have but the principal is the same.
*Do not drill from inside to outside as there is a slight step usually so doing this may cause damage to the window or door.
**Before drilling measure the width of the vent to select the correct size of drill bit to use.
Link below to the vents you can purchase online...
www.double-glazing-parts-spar...
Thanks again for watching and hopefully it has helped someone :-)
Пікірлер: 49
Great video, thanks.
@DGPSUK
11 ай бұрын
Very welcome, thank you 😊
Cheers very helpful 👍
@DGPSUK
8 ай бұрын
Very welcome 😊
what kind of worker should i hire to install a vented hood? i need the hood to be vented through a double glazed window in kitchen. so i think I'll need some kind of glass worker. but i don't know what qualification worker i should look for?
The film infers that it is not necessary to cut a continuous slot and that it is ok to just drill a series of holes. It is, but beware - for a typical 400mm vent, the holes would have to be spaced with just 1.6mm between them to achieve the mandatory design airflow...
@darronroper
5 ай бұрын
You can drill out, but still need to route the entire gap out using a palm router, or even multi tool. Keeps air flow to the max ( which is what you want) and gives a professional and clean finish. If you are retrofitting for building regs they will fail the works!
Thank you
@DGPSUK
Жыл бұрын
Very welcome 😊
I'd watched this video about 20 times before I attempted on my windows. I got a 13mm HSS bit especially for the job, but it would sometimes catch in my uPVC and my hand drill struggled, so in the end I used an oscillating multitool which worked much better. I marked out the template on masking tape as my window frames are black, then cut carefully along the lines. I used a smaller drill bit for the rounded edges. Hope someone else finds this useful. Actually quite straightforward once you know what you're doing.
@DGPSUK
2 ай бұрын
Thank you for the great info, 😊😊
looks straightforward, is it always the opening panel that you fit to, or can you also fit to a fixed frame?
@DGPSUK
10 ай бұрын
Hi, yes can be done through the frame also 👍
Super thing, but not in too windy places.
@DGPSUK
Жыл бұрын
You could always pack the vent with soft foam or sponge to stop any loud noises from the wind and still get some ventilation 😉
@Sattrecamuss
Жыл бұрын
@@DGPSUKI have installed this kind of valves and It has a filter, some kind of sponge, but I'm living at the seaside, it's almost always windy here. It's ok in a quet weather, but in a windy weather these valves whistling all the day long, even you close them.
@DGPSUK
Жыл бұрын
@@Sattrecamuss Yes they can be annoying especially where you live 🙈🙉
Is there any way to easily test that air is flowing? As you can't drill a hole right through to the other side and have to drill on both sides I'm not sure if I did it right or stopped short. I drilled on both sides until I hit something solid.
@DGPSUK
Жыл бұрын
Hi, you should be able to see daylight, test at night when it's completely dark or hold a flame to the inside where you drilled and see if it gets disturbed. 👍
@WillsM85
Жыл бұрын
@@DGPSUK Will do. Thanks a lot!
@DGPSUK
Жыл бұрын
@@WillsM85 very welcome
If you dont drill through the internal metal do they still work? Thanks Tom
@DGPSUK
8 ай бұрын
Depending on the profile you may get some ventilation but not as effective as drilling through.
Do new windows come with pre installed vents cause 6iu never see these on new windows
@DGPSUK
7 ай бұрын
Hi, they can yes but it is an optional extra, normally they are required in new builds though?.
Instead of drilling multiple holes all the way along, could you use a multitool?
@DGPSUK
Жыл бұрын
Most definitely could just need a steady hand 👍
@YouStoleMyMash11
Жыл бұрын
Thanks for getting back to me 👍🏻
@DGPSUK
Жыл бұрын
@@YouStoleMyMash11 no problem at all 😊
I have encourntered a metal barrie in some of my windows. Is it OK to drill through it?
@DGPSUK
Жыл бұрын
Yes you can it's just reinforcement 👍 just takes a little longer. 😊
@ardentlieutenant3390
Жыл бұрын
@@DGPSUK Thanks. I note the upper windows that swing up do not have this metal although there may be a second layer. None the less when finished I can see through Ny wondows anr Anglia and another manufacturer and were installed at fdifferent times. and seem to have different construction.
@DGPSUK
Жыл бұрын
@@ardentlieutenant3390 Hi yes different window profile extruders will have a different design and chambers but more or less the same idea, some companies also don't use reinforcement and some do. Hope it all goes well for you 😊
@ardentlieutenant3390
Жыл бұрын
Thanks I used a smaller drill bit and then enlarged it. It was quite a job and I broke a few bits as I was doing it freehand with the window in place.
@DGPSUK
Жыл бұрын
@@ardentlieutenant3390 yes it can be a tedious job but can definitely be worth all the effort in the end 😊
Roughly how many trickle vents would you require for 3m X 3m conservatory please.
@DGPSUK
5 ай бұрын
Hi it does vary, have a look at the following... www.norrsken.co.uk/newsitem/trickle-vents-guidance-ventilation-part-f#:~:text=HOW%20MANY%20TRICKLE%20VENTS%20DO,has%20more%20than%20one%20bedroom.
@user-ts1mk6xt4j
5 ай бұрын
Thank you @@DGPSUK
Can you install these on already installed windows
@DGPSUK
6 ай бұрын
Yes of course, this is what this video was intended to help with. 😊
@wazzy12
6 ай бұрын
@DGPSUK I have dekurnik sliding doors just wondering where you would advise to put them on the 4 panel, the 2 central sliding doors or the 2 side panels
Did I miss your explanation why you do inside then outside due to the step? You said you explain later on? When later on?
@DGPSUK
8 ай бұрын
Hi, Oh sorry I'll double check, it's basically you can't drill all the way through on most profiles as there is a step and it wouldn't come through the other side where it's needed.
@DGPSUK
8 ай бұрын
I basically cover it straight after I mention it. 😊
@epictraveller4862
8 ай бұрын
@@DGPSUK ok thanks. Wish the people who we bought the house off got windows fitted with them already. Not even that old either.
@epictraveller4862
8 ай бұрын
@@DGPSUK ah right thought there was more later on 👍🏻
A window that big should have steel
@DGPSUK
10 ай бұрын
It does yes ? 👍