How to reset 370z & g37 check engine light
Фильм және анимация
Turn the ignition key to position “ON” without starting the engine and wait 3 seconds.
Fully press and release the accelerator pedal five times within 5 seconds.
Wait 7 seconds
Fully depress the accelerator pedal all the way to the floor and hold for ten seconds. until the CEL starts blinking.
At this point, the light CEL should start flashing error code stored in the system and you can release the pedal. If you only get five flashes slowly or not flashing at all, then it is time You went on one of the above steps and you have to start from scratch.
Fully release the accelerator pedal (while the CEL is still blinking) and wait about 10 seconds.
Fully depress the accelerator pedal and keep it for more than 10 seconds.
Fully release the accelerator pedal (The CEL light will continue to blink).
Turn the ignition off and start the engine to verify the indicator has been reset.
Пікірлер: 33
What I did was basically follow his steps while the video played and counting in my head to be sure enough time passed but definitely helped me out and the service light is gone I’ll see in the morning if it holds (I have a manual 370z worked fine)
This worked on my G37 2009. Thanks. *I had my check engine service light on because I replaced my catalytic converters with straight pipes, so the sensors were left out unplugged*
Awesome. Wouldnt have done it without this amazing and easy tutorial. Thanks kindly
Did this on my 2018 Z, took me 15+ tries. It's all about timing and knowing the instructions. You can do it, just might take a minute
@humorlesscomedy7657
3 жыл бұрын
Mainly timing did it first try on my 2012 g37
@teddyfuxspin1978
3 жыл бұрын
This didn't work I'm sure I just screwed it up
This works on my 2017 370z Nismo. Thank you awesome.
Its do cool thank you!!!! My engine oil sensor has a problem and now it's working and could erase check engine light! Greetings from Luxembourg, happy new year!
*please use a timer while doing this, do not estimate the time Turn the ignition key to position “ON” without starting the engine and wait 3 seconds. Fully press and release the accelerator pedal five times within 5 seconds. Wait 7 seconds Fully depress the accelerator pedal all the way to the floor and hold for ten seconds. until the CEL starts blinking. At this point, the light CEL should start flashing error code stored in the system and you can release the pedal. If you only get five flashes slowly or not flashing at all, then it is time You went on one of the above steps and you have to start from scratch. Fully release the accelerator pedal (while the CEL is still blinking) and wait about 10 seconds. Fully depress the accelerator pedal and keep it for more than 10 seconds. Fully release the accelerator pedal (The CEL light will continue to blink). Turn the ignition off and start the engine to verify the indicator has been reset.
@luismaldonado1837
3 жыл бұрын
Dont work in my 370z 2010 why???
@ahmadabdel9114
3 жыл бұрын
@@luismaldonado1837 you are probably not doing it correctly. it worked on my 2009. Try setting a timer while doing it
@miniquadsmegafun3619
Жыл бұрын
This worked for me!! Thanks!!
Thank you. this worked after 4 tries. however my service engine light came back on 30seconds after I turned the car on.
Is real good work for me thank you
Thanks so much sharing! I was able to reset the CEL on my husband’s Nismo!
@davidvillegas3525
3 жыл бұрын
How did you get it to work for your h. nismo? It’s not working for mine I have a 13’ nismo
Does it matter what year it is cause I have a 2016 and I’ve tried this multiple times and it doesn’t work unless I’m doing something else wrong
Thanks again for sharing. Your notes worked perfectly.😎
@MrBansheez
Жыл бұрын
Sure you have checked before with computer and know what sensor note work represents then power car gives you best hp
Thank you bro
Why was the check engine light blinking
FRESH!
It's same in manual transmission?
I have a check engine light due to my test pipes, will this hide the code when reading it with a obd2 scanner even though the check engine light is now off?
@ahmadabdel9114
2 жыл бұрын
The light will come back on after a while... it wont read it on the obd2 sensor but you will fail inspection
@ajet_aaronmacias9437
2 жыл бұрын
Bro my 370z is acting funny and misfiring after I installed test pipes and Cai I gotta Make it 3 or 4 weeks til I can get the dam thing tuned hopefully that takes car of it
@MrBradyy88
Жыл бұрын
Bro happened to me and the ecu went out doing both those mods, had to find exact model and year to the T ecu. Haven't had problems since. Was a pain in the ass to find exact ecu.
How does the 370z low tire pressure light turn off?
@tovopro
2 жыл бұрын
Make sure all tires are properly inflated. This is the time of year when tire pressure goes low because of the outside temperature drop from hot to cold. That’s normal, but definitely properly inflate, drive around for quarter mile, and the low tire pressure should vanish on its own. 👍
@MrBradyy88
Жыл бұрын
Replace the bad tpms sensor
Did not work. My car keep stop blinking
@_Zoctane
Жыл бұрын
What do you mean blinking