How to Replace Wheel Bearing 2012-2017 Toyota Camry
Автокөліктер мен көлік құралдары
Buy Now!
New Wheel Bearing from 1AAuto.com 1aau.to/ib/TKAXX00021
This video shows you how to install a new bearing on your 2012-2017 Toyota Camry. Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision.
This process should be similar on the following vehicles:
2012 Toyota Camry
2013 Toyota Camry
2014 Toyota Camry
2015 Toyota Camry
2016 Toyota Camry
2017 Toyota Camry
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oaZT/1AXAA00013
• Pry Bar 1aau.to/oHV/1AXAA00020
• 10mm Wrench 1aau.to/oKL/1AXAA00010
• 22mm Wrench
• 10mm Socket 1aau.to/oaKH/1AXAA00017
• 14mm Socket 1aau.to/oa2K/1AXAA00015
• 17mm Socket 1aau.to/oa2K/1AXAA00015
• 18mm Socket 1aau.to/oZU/1AXAA00043
• 19mm Socket 1aau.to/oZU/1AXAA00043
• 22mm Socket 1aau.to/okK/1AXAA00266
• 33mm
• Air Compressor
• Blowtorch
• Brake Caliper Hanger 1aau.to/ogp/1AXAA00084
• Press
• Pliers
• Side Cutters
• Snap Ring Pliers
• Air Chisel 1aau.to/oaV/1AXAA00270
• Ratchet 1aau.to/obet/1AXAA00016
• Torque Wrench 1aau.to/oakr/1AXAA00044
• Drill
• Cotter Pin
• Gloves 1aau.to/ox4/1AXSS00048
• Rust Penetrant
• Safety Glasses 1aau.to/osm/1AXAA00343
• Hammer 1aau.to/oKS/1AXAA00091
• Pick 1aau.to/oDM/1AXAA00037
• Punch
• Sledge Hammer 1aau.to/oKS/1AXAA00091
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
Пікірлер: 21
√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money
Anyone else say F it and just drop the money for the Wheel Bearing/Hub/Knuckle assembly? 😂 a far easier install.
ITS A 30mm SOCKET NOT A 33mm
Watching him drop his tools every so often makes me feel a bit better about learning cuz i can't seem to keep ahold on mine most of the time either
Very well done. One of my wheel bearings gave out after only 102,000 miles. I was a little surprised, given Toyota's reputation for quality. At my age, (80) I just don't want to fool with the problem so I took the car to a local repair shop which is replacing both bearings for $1500.00. OUCH! ( In fairness, This is a lot more complex a procedure than when I used to do my own wrenching on my cars.)
I like that the big green impact is called Fartnocker.
Thank you for this. I am going to tackle this job soon on my dads Avalon. I couldn’t help but laugh when you cut the vid short while removing the race from the old hub…then in the next scene, you’re installing a brand new hub 😂. I am going to try to reuse my dads old hubs….wish me luck.
Damn, guess I’m gonna have to buy a few more tools to tackle this one!
Outstanding video! Thank you for sharing.
So why not just remove the caliper and bracket as one whole piece?
Thanks for the video
if you buy the whole hub/bearing assembly do you still have to remove the old bearing or just replace it a whole? I know is a dumb question but i rather know.
Thank you so much nice job
A lot of effort involved, surprised Toyota didn't come up with an easier way. Did the front ones on a Ford a few years ago, very simple case of undoing one bolt in the centre pulling out the old hub then replacing it with a new hub. Good video.
Hey, so after I did this job, my wheel wont turn fully left or right? Any advice?
Does the hub have to be replaced, can’t you reuse the old one?
@TRQ
8 ай бұрын
+Ryan Angus It is not necessary to replace the hub if it is in good condition.
😀
You don't have to go through all that just to remove the hub
It's too zoomed in. I can't see where on the car these things are. I'm trying to learn 😭
nice thx