Fantastic video. No annoying music or pointless "production" tricks and NO vertical video. Just the info, clear and concise. Give yourself a pat on the back mate. Well done.

@6thGearGarage

6 ай бұрын

Thank you! Also, I can't stand vertical video!

I was dreading this process, but then I saw that your video isn't too long. I'm very relieved that I don't have to take the entire thing apart. Thank you!

@6thGearGarage

3 ай бұрын

Glad the video could help!

Toyota Master Tech here. The u joint does not have to maintain the same alignment with the pinion flange. It’s only when you’re disassembling a driveshaft that you have to make sure everything is indexed properly. The driveshaft is not balanced while attached to the pinion flange so that is why it doesn’t matter. If you noticed in your video, you do not necessarily reinstall the pinion flange on the same pinion splines so it makes no difference.

@6thGearGarage

3 жыл бұрын

Jacob Dionne thanks for the tech👍

@jacobdionne4334

3 жыл бұрын

@@6thGearGarage no problem

@thelandcruiserproject

3 жыл бұрын

@@jacobdionne4334 Did the 90 ft-lbs of torque on the pinion nut really matter when you already had it aligned with the previous staking mark? Or is the 90 ft-lbs just a good rule of thumb if you fail to count turns?

@jacobdionne4334

3 жыл бұрын

@@thelandcruiserproject it depends what you’re doing. If you doing anything but simply replacing the pinion seal then you have to replace the crush sleeve and retorque.

@thelandcruiserproject

3 жыл бұрын

@@jacobdionne4334 Only replaced the pinion flange. Had a wear line that let a new seal leak.

This video was super helpful. Love the tip about the 54mm socket to get the seal in, was having no luck with other methods. It did made the job a breeze once I got it.

@6thGearGarage

3 жыл бұрын

Andrew Griffiths glad to hear it worked👍

This has to be the cleanest undercarriage that I’ve seen

Sweet video. I'll need to do this soon on my 88 dually resto-mod. Very helpful! Please make some proper triangular/wedge wheel chocks though. Wayyy safer than 2x4s. You're too valuable to lose to a shop accident! Thanks for all your videos and stay safe!

@6thGearGarage

3 жыл бұрын

Thanks! 👍

Love the Toyota videos, keep them coming👍

I am very happy about this video because I need to complete the same job! Thank you 6th gear garage!

@alfredobrown

4 жыл бұрын

I also have to do it (actually, I have to re do it)

Very good video. I really like the voice-over and you explained every move perfectly. Also, I immediately saw that you have the ideal tires on your truck. Too many folks put too-wides on them. They look great but are inefficient in the rough and fuel consumption. Liked, sub'd.

@wahiawabound808

7 ай бұрын

In hawaii we make it wide there's multiple purposes for going wide stability is 1 and 2 we are surrounded by ocean which equals sand and we noticed wider wheels make better contact for riding on the sand now narrow wheels is good for mud it cuts through better than wide wheels we also noticed narrow wheels work good in the mountains. At the end of the day it all boils down to what you'll be using your rig for some people put wide wheels just for that aggressive look which to me is ok but very useless especially when using it on a 2 wheel drive I think lifting a 2 wheel drive in general is useless again it boils down to preference have a good day man.

awesome. I need to redo my rear pinion seal on my 87’ 4x4 pickup. This is perfect! much appreciated!

Nice work thanks for all the first instructions and advice! Well done mate!

You make it look so easy, but I got it! Thanks for the awesome video!

Simple enough,I’ve heard it can b done easily, Mine just started leaking, thanks for the great video

Great video. Worked for me. I also left 2 bolts in the drive shaft and proped a crow bar against them and held the pinion flange still with that so the truck wouldn't move. Not sure if better or worse but it worked and no more leak. Thanks!

@6thGearGarage

3 жыл бұрын

Thanks and good idea!!

Great video! Thanks for taking the time to make it.

Awesome work I’m really looking forward to working on my 86 four-wheel-drive original 130 3000 miles with air-conditioning mind you I can’t wait to watch that video

Thanks for all the information and the other videos. Definitely makes it A LOT easier to work on my own truck so i don't get the stiffy from a mechanic

@westongenesis7007

2 жыл бұрын

you all probably dont give a damn but does someone know of a method to get back into an instagram account?? I was stupid lost the password. I love any tricks you can offer me.

@olivermaximo4149

2 жыл бұрын

@Weston Genesis Instablaster ;)

Well hopefully I can fix mine this weeknd. Not a big mechanic person trying to learn to do it all on my own. Thanks for the videos man they help alot.

@6thGearGarage

3 жыл бұрын

Glad to help

@matoko123

8 ай бұрын

Did you succeed?

Thanks for sharing 👍 Super helpful, I was dreading doing this until I watched your video .

When I was redoing my Tahoe's rear axle pinion seal I put the nut back on with an impact and ever since the rear pinion seal leaks and I can move the driveshaft up and down at the yoke. I didn't know better back then but believe it or not I still have not fixed it. Been running the truck like that for about 12 years now. Man them 14 bolts are tough.

@6thGearGarage

4 жыл бұрын

Gamblin!! But yeah thats amazing it's been ok for 14 years!

Your video is so descriptive, thank you so much this will really help

Very helpful. I was about to go hog wild on a friend's differential and tear the whole thing apart for that front oil seal.

this was great i need to replace seal on my 89 supra this was just what i was looking for! thankyou

Well explained! I have the same truck and I’m about to do this. And while I have the FSM’s too, this video is certainly well worth 1,000 words! It looks like I need to order that wheel bearing socket first. I don’t see what else I could improvise with to set the seal, ..maybe 2 or 3” PVC pipe and a cap.

@6thGearGarage

2 жыл бұрын

Yeah a thick pipe would work too, anything you have laying around with the same outer diameter.

@oldowl4290

2 жыл бұрын

@@6thGearGarage I wound up using a white 2" PVC pipe end cap. They are for 2" pipe but are 2.75" wide in total, leaving ~ 2mm of room all the way around. It took several tries to get it seated right as one side would go in more, causing the other side to pop up. So I also used a small wooden block and 8oz tack hammer to lightly tap around the perimeter then smack with the centered PVC cap. It worked well and I finally got it in. It wasn't quite as easy as your video makes it out to be but I got it done!

@6thGearGarage

2 жыл бұрын

@@oldowl4290 Nice work!!

Brilliant video mate, very easy to understand..cheers

This video was so helpful, thank you.

Great vid Doing this tomorrow on my 96 uk mk3. I don’t need to rush out and but a puller do I, I can just gently tap it off

@6thGearGarage

3 жыл бұрын

Oh you mean for the flange? Yeah you need a puller to get it off.

How did you lift your 87 2wd? I commented earlier, ballpoint spacer??? Or more tension on torsion key? Want to know for my fun field/drag truck

You made it look easy. Thanks for the good tips.

It’s actually not as important to count the turns on the nut as it may seem. The crush washers are pretty stiff, if you just run it back down and don’t hammer on it too much with an impact, you’ll be fine. But I’d put a mark on the nut and the pinion shaft so you have a good idea of where the nut was. Toyotas diffs aren’t very sensitive, thankfully.

Good work dude , I had a dripping oil from my differential, not much really, one drop a day , on a clean surface, that's too much. I have 84 Toyota Cressida,its differential is as your pickup, it uses the same oil seal number. I was encouraged by your video , to do the job, I did it exactly as you did. The shiny nut , took little torque to loose , I didn't bother counting the turns, just remember the place, no way to be missed, I had a very hard time removing the old seal, I freezed the new seal for easy fit,I retightened the shiny 24 mm nut , again not the torque you stated , but with the torque it needed to put it , where it was before, removing the pinion was very easy , no tool was needed . And something, that you didn't mention , which is to empty the oil from the diff. Before you start, I created a mess by that . And pour a new gear oil in it , around 1.4 L ,to keep diff. And seals in good shape . Thanks again for posting this video.

@mazen723

2 жыл бұрын

kzread.info/dash/bejne/m52j0KaPg7a8lco.html

@6thGearGarage

2 жыл бұрын

Good call on draining the fluid. I didn't need to because my truck is lifted, so the pinion angle is up for the driveshaft to meet the transfer case. But on a car you will definitely want to drain the fluid to avoid a mess.

Great video and sweet Toyota man!

@6thGearGarage

2 жыл бұрын

Thanks! I’m obsessed with old Toyotas.

Well done, good footage and narration

@6thGearGarage

6 ай бұрын

Thanks!

Thanks for the lock nut torque spec i was wondering what it was👍

Best explanation ever,,

you dont need special tools for pulling the seal, you screw in 2 screws on the face of the seal and then pull on the screw head with nail puller. :)

Really enjoyed that. My wife has bought a 1994 HiAce with this exact problem. I live in the UK and van is import so I can not find anywhere to buy the seal. If you or anyone have any ideas it would be greatly appreciated.

Engineers who write the manuals make everything so absurdly complicated. Great video and tutorial.

@ken85225

Жыл бұрын

djr------BIG 10-4 on the engineers getting ridiculous

Thank you so much for sharing this great video, you did a great job

@6thGearGarage

Жыл бұрын

Thank you!

Excellent! Thanks for the vid!

Saved Me Big Buck Thanks Master

Perfect job you make easy

Great video thank you for your time..😎

Outstanding!

Don't forget to check breather on top, (my 08 doesn't have a hose) it should spin freely..If clogged it will also cause seal failure..i removed mine and used Gunk spray to loosen it..

@6thGearGarage

3 жыл бұрын

Very good tip!

@loudowning3393

Жыл бұрын

The axle vent clogged on my 1990 4runner causing the pinion oil seal leak. Check this little bugger every once in a while to save heartache

Dios les bdendiga mucho,gracias por la informacion sobre como intalar el retenedor nuevo a la toyota pick up muy huena intruciones de como intalarlo. Que Dios les siga bendiciendo sigan hacia delante. Gracias muchas.

great vid. i'm about to attempt this on my 1991 4runner, wish me luck bro.

@6thGearGarage

2 жыл бұрын

Thanks, you got this!!

@tonyisme4934

2 жыл бұрын

If you haven't done this yet, try 1.2oz of ATP 205 in the differential. I had a chronic leak for years, yesterday I changed to Mobil 1 Syn GL5 and added 1.2oz of ATP 205 and my leak as ceased thus far. But I do have the OEM Toyota Seal standing by.... The ATP 2oz worked on my steering gear box leak also. That has been 6 months ago. I have 1990 4Runner, 306,000 miles.

great tutorial buddy, thank you.

@6thGearGarage

Жыл бұрын

You're welcome!!

That’s a sweet Toyota.

Thanks for sharing great job. 👍 😊 from rick Perth,😊 Australia 🇦🇺

Awsome video.well explains excellent

Thank you for the nice video.

😢 I don't know where else to go. NO mechanic could figure out my problem. I know this the only place that has the answer. I have 98 4runner with 140k, which I gave my son to use. Recently, the car shutter around 50 mph, it feels like it's searching for gear (going up and down shifting) but I know it's not a transmission issue. Only a few think that I can detect, the tranfercase has a front drive shaft seal leak, probably half of the fuild is gone. And the other was a recent front brake pad change. Clicking sound is heard on driverside drive axle spinning it, car shakes around 60-70 after brake change. PLEASE can someone give me some pointer on where to look. Thx u.

Great video. If you torque it to a specific ft lbs, the prior step of counting the turns is pointless, no? It's going to stop at 90 ft lbs regardless and wind up in the same position. Also, did you make the shaft and the yoke even though you didn't separate them? I may have missed it but seems like the only thing you'd need to mark, if anything at all, is the yoke and the diff flange mating surface.

@6thGearGarage

6 ай бұрын

Yeah, you're right. I wanted to have a backup way to keep track, just in case something was way off. And yeah, once again, I'm in the habit of marking it all just in case.

Huge help!

Can you use the "count the turns" method for the front pinion seal for the front diff?

@6thGearGarage

3 жыл бұрын

You can, but for a piece of mind I bought an in/lbs dial torque wrench to properly set preload when I replaced the front pinion seal on my land cruiser.

Good job 👏

Great video

@6thGearGarage

9 ай бұрын

Thanks!

You verify that the rotation torque is in spec. After you reach 90lbs. Should be around 10-12 inch pounds. You will need to jack the rear off the ground. That verifies the preload has not changed.

Good job bro

Awesome video, mine is leaking pretty good to the point where it’s slinging up on the undercarriage. You think it’s safe to drive a few miles to the Autoparts store? I’m afraid to grenade my rear diff 😬

@6thGearGarage

2 жыл бұрын

Yeah, but I'd check the fluid level first, make sure it's not too low.

Good job man

It was actually 10x easier to take the seal out this way than when I had completely removed the 3rd member. LOL

@6thGearGarage

2 ай бұрын

If there's an easier way, I'm doing it!

There is NO way that truck spent it's life in Ohio! Thanks for the video, I have a '77 Toyota FJ40 I need to tighten the pinion nut on, this will help a lot! Let me know if you want to do a video on how to replace the knuckle seals, I'll be happy to loan you my 40! ;)

@6thGearGarage

4 жыл бұрын

Dianna Poe I think it was a West Virginia Truck before it ended up in Ohio. I’ve always wanted a 40... if I could only have a small Toyota collection... my 85 needs new seals up front as well, so there will be a video for a front axle rebuild eventually.👍

I'm doing this to my '91 4runner and I'm wondering if with the companion flange removed, is it ok that the pinion wiggles in place? Or can there be a problem with the inner bearing? Any help would be appreciated. Thanks

@6thGearGarage

3 жыл бұрын

The companion flange holds the pinion in the center, so some movement is ok. I've had some that moved a lot and some that didnt.

Awesome video cheers

@6thGearGarage

3 жыл бұрын

Thanks 👍

Good job 👍

Excellent

Thanks for the share....

@6thGearGarage

Жыл бұрын

You bet!

Buen trabajo me alludo mucho en mi troca

Excellent video but you should have marked the pinion shaft with the flange it's more important than marking the drive shaft to the flange, my workshop manual recommends to mark the flange with the pinion shaft. Also you can fit two bolts and four nuts to the flange then you can get purchase using a prybar locked off to the springs, saves chocking wheels a mate.

thnx

Dam great video I got an 86 and I've got massive vibration some guys I bought it from may have installed gearing and didn't torque the pinion flange bolt correctly the flange moves alot so I dropped the driveshaft and noticed the bolt can turn with your finger and they locked it in like that smfh I put everything back but tomorrow ill just torque it down to 90ft lbs and see if the vibration goes away.

@wahiawabound808

7 ай бұрын

Yes so I torqued it down and yes the vibration stopped then starting to come back not as bad so I think it loosened up again so sometime this week I'll tend to it again. I'm guessing they tried to install the gears themselves and didn't know what they were doing with the install I don't even think they preloaded anything lmao.

Cheers Man big Help thanks :)

Great video mate and greetings from downunder. I have a HJ61 Landcruiser that needs the same job done and your video is spot on. I couldn’t see the tool list as you mentioned in the comments. Can you please resend?

@6thGearGarage

2 жыл бұрын

The list is in the video description, not in the comments. Click to read the description for the full list.

@6thGearGarage

2 жыл бұрын

Thanks for checking out the video and nice rig... wish we got the diesel in the US.

@mohdeen8682

2 жыл бұрын

@@6thGearGarage ok so I had to ask my daughter to check and you can’t actually see the info via KZread on your mobile phone. Need to view it on your computer and there it was. Cheers

Man I realized mine was leaking about a week ago .... never searched "how to's" or said it out loud or told anyone...🤨🤨🤨🤨... The government is getting good.

@6thGearGarage

3 жыл бұрын

It's scary isn't it? I talked about buying something and now it shows up all over FB marketplace suggestions.

Thank you for the video

@6thGearGarage

3 жыл бұрын

You're welcome

@jdhitc

3 жыл бұрын

Hey, sooooo what if I can't get the OEM mark on the nut to bolt to completely line up... Close but off...😬

Nice

Great video...jc

Can you leave oil in the diff for the front as well when you change the pinion seal??

@6thGearGarage

Жыл бұрын

Yes I left the diff oil in when changing the front pinion seal on my land cruiser and it doesn't leak out. That was a different axle though, so maybe have a drain pan nearby just in case.

Tire size. 33/10.5R15 ? Great Video by the way.

After pulling my seal I noticed the pinion has some play in it but it doesn’t look like yours does in the video. Should they have some play if the nut is off?

@6thGearGarage

4 жыл бұрын

I’m not sure, how much play and how many miles?

@kylebowling3042

4 жыл бұрын

6th Gear Garage wow! thanks for the reply! 220k miles. Once the nut was removed the front bearing was free to move around. I was able to pull the front pinion bearing and inspect it and it was good. Once reassembled it’s was tight. The nut also threaded a quarter turn past the original location as well. Wondering if I shouldn’t rebuild it all now. Thoughts?

Noticed gear oil on the ground right below my pinion seal. I had replaced this seal just over 2 years ago with the factory Toyota part. Any idea why it would fail so soon? Thinking I did something wrong the first time... could I get away with just keeping an eye on the rear diff oil level and adding oil accordingly?

@6thGearGarage

3 жыл бұрын

A clogged breather can cause excess pressure, making the seal leak. Check that first.

@ChekeredFreak

3 жыл бұрын

@@6thGearGarage thanks for the tip! Will check that first before further diagnosing

Thanks for the video

@6thGearGarage

Жыл бұрын

Glad it helped!

@hassanshaier1464

Жыл бұрын

@@6thGearGarage very much thanks again

Damn i like your toyota what a tank

Nice!

10:35 Good trick with Toyota's is jack up the right side and get some more oil in there. They're not like independent axles or gearboxes that requires a specific amount of oil, the more oil the merrier. Also if your Toyota has a Limited Slip diff, don't use the cheapo 90W LS oil, splurge on the Castrol 75W140 BMW Limited Slip oil, it has better properties to retain friction between the clutch plates to grab onto one another, and does a better job of washing off worn friction material.

I had my rear pinion seal changed now I get random metal on metal chirping and grinding and shuddering in the front. Do you think its related..? 2008 jeep grand cherokee 3.7 with 166,000 My differential is fine, no whiring sound.? 😊

@6thGearGarage

2 жыл бұрын

I,m no jeep expert, but I don't think it could be related

@gingin1050

2 жыл бұрын

@@6thGearGarage thank you

Good video...

@6thGearGarage

2 жыл бұрын

Thanks!

For the 30 mm socket are you using a 12 point or 6 point socket ?

@6thGearGarage

3 жыл бұрын

It’s a 6 point

@joshreyes8504

3 жыл бұрын

6th Gear Garage thank you 🙏🏽, I am trying to service my brothers pickup, I came across this video and it’s so informative.

Great video thanks so much

I’m having problems with my 1987 extra cab 4 x 4 I had to change the clutch master cylinder three times aftermarket have you had the same problem?

@6thGearGarage

4 жыл бұрын

Although I've been told aftermarket ones from parts stores are china quality, I have not had one fail. How are yours failing? Where are they leaking?

@alfonsocasillas7290

4 жыл бұрын

No they just start losing pressure no suction

@6thGearGarage

4 жыл бұрын

@@alfonsocasillas7290 Maybe the seal inside is wearing out? That's weird it's happened 3 times now. Hope they had a warranty on the parts!

great common sense procedure for DIYers

So you don't have to drain the diff oil beforehand?

@6thGearGarage

4 жыл бұрын

I did not. The angle of the rear axle did not allow fluid to leak from the front.

Guessing 225/75r15 🧐 great video man

@6thGearGarage

4 жыл бұрын

close... 33x10.50r15

Anyone know any tricks for getting the flange back on the spline? I cleaned everything carefully and put some anti-sieze on the spline to try to lubricate it, but after fighting it for a couple of hours, I can't get it on there.

@6thGearGarage

2 ай бұрын

The alignment and angle has to be perfect due to the tight tolerances. I'd give it another try.

@Dwigt_Rortugal

2 ай бұрын

​@@6thGearGarageCool, thanks so much. I guess I'm just a nervous novice 😂. I have an 8.4 with 30 splines regeared to 4.88. I paid a local expert to install the 4.88 Nitro Gear kit. Talking to someone else much more competent than me, it sounds like this combination in particular requires a little persuasion. I might use some freeze spray to try to get the spline to shrink slightly. No idea if that'll help. The other thing I'm going to try is inspecting the spline carefully and using a triangular file to gently clean it up if something is out of whack.

The parking brake works? Intreseting

@6thGearGarage

3 жыл бұрын

Very rare feature!

Marking the drive shaft doesn’t help unless you put the flange back on the spline in the same orientation it was removed.

Thanks.

@6thGearGarage

2 жыл бұрын

You're welcome

3:28 my flange comes off with just a few wiggles back and forth that shouldn’t be normal and also the washer that goes on the companion flange is that important? Mine didn’t have it and it’s leaking worse that it did before i changed it literally all the diff fluid came out

@6thGearGarage

4 күн бұрын

I say if Toyota engineers put the washer there, it must be for a good reason.