Good video man very helpful thanks ,I’m working on my c300 this weekend same exact problem and this video is going to make the process so much easier

@F80__6MT

Жыл бұрын

Thanks for the feedback it motivates me to record more video.

@John-fv3bz

Жыл бұрын

Did you lose any transmission fluid when you replaced the radiator?

I also bought the nissens radiator and the hoses along with the coolant reservoir, cap, water pump, thermostat, idle pulleys, and just missing the belt tensioner . As soon as i get that tensioner, i will out everything all at once. I have a 2011 glk350.

So how many tubes total ? I noticed 3 big black ones and than 2 small metal ones on the left side ? I’m writing everything down so I can do this in the next month or so thanks so much you’re awesome man !

Idk how to feel about the angles and the bottom- side instruction. How do you remove the lines?

You are awesome. So much appreciated Thank you for sharing 🙏

I remember paying someone 500$ for this job.. I had to change out the fan myself and realized i could have done it myself..

Did you lose any transmission fluid during the change? Was a top up needed?

Thanks for this man - got quoted over $2K for same job today. Found DIY motivation thru this video! Is the Nissen radiator holding up?

@F80__6MT

Жыл бұрын

Thanks for the comment. Glad you will be saving some money. Radiator has been great with no issues.

Hey brother, so how do you do the bleed procedure on this vehicle? I know you said leave the heater on full blast.. and leave it on, and the thermostat will open? Is that when it’s technically bleeding? But in order for the thermostat to open up you clearly need to close the reservoir cap correct? Then at that point the coolant will go “ down “ and you’ll reopen the cap and fill it up again? Or am I missing something , thank you.

@F80__6MT

7 ай бұрын

Fill system with radiator fluid and you can keep radiator cap off during this process. Start car and turn max heat on. Let run for 10-15 mins and when fkuid drops fill it. When it no longer drops you should be good and can put cap on. Check it after next drive cycle.

@stgmaofficial

7 ай бұрын

@@F80__6MT you’re a beast!! Thank you man

@stgmaofficial

6 ай бұрын

@@F80__6MT I went ahead, and did everything like you stated the coolant did lower after two hours, within a two hour. The car was off for some reason now my heater isn’t working. I think I still have air in the system somehow is there anything else you did? Do you need to push on the upper radiator hoses while the heater is on? Sorry for the bother and thank you for the help. It means a lot.

@F80__6MT

6 ай бұрын

@stgmaofficial You may still have air in the lines. Park on a hill so that there is angle. This will force air to the highest areas. Turn heat on full blast and bleed it that way. Your heater core has air which is why it's not radiating heat.

@stgmaofficial

6 ай бұрын

@@F80__6MT thank you! That’s exactly what I was thinking! The first time I bled it I had followed your instructions and the radiator cap was off, but for some reason it was overflowing violently, so I let the car rest for 2+ hours then the coolant finally went down gradually, while the car was off, I then topped it off now the coolant is at the supposed fill level, but once again, I know it has air because the heater isn’t working and it was prior to the radiator change. So my last question is if I bleed it how you’re saying at an angle do you think it’s going to start bleeding out violently again? If so, when do I turn off the car so it doesn’t do that or is that normal? Meaning a lot of air is coming out .. thank you so much Bro it means the world that you’re helping me

Why you did not unscrew the liquor hose from the top of the ratoratar

Hello, can you give me a tip? I also have to change my radiator because the screw at the bottom is broken and it always comes out. Do I now have to unscrew the entire front of the car or can I leave the bumper on? I have an E200 CGi A207 Type M271 Evo engine built in 2010

@F80__6MT

11 ай бұрын

You can leave the bumper on but may have to remove front grill. Usually held together through plastic clips.

@user-bw5hk5nb3k

11 ай бұрын

Please can u help i have remove the old one but i cant install the new one it is really soo hell 😞 what i must doo ?

Same failure on my 2010 c300 at 170k miles.

Hi Sir,. I have a 2008 c300 leaking fluid from the botom of radiator, and my car is overheating on iddle,, do you think this cause the overheating, and how many hours this job with no to much experience.,,???

@F80__6MT

Жыл бұрын

A leak can cause the car to overheat. Leak introduces air into the cooling system, which may cause it to run hotter. I'd plan for 4-6 hrs with little to no experience as long as you can watch these videos in between. Best of luck to you.

@leonelchavajay8564

Жыл бұрын

Thank you sir,, i just bought it a week ago,, 2008 c300 sport, 173,000 miles i payed $1,800 for it, i think its a good price??

@F80__6MT

Жыл бұрын

@leonelchavajay8564 In my opinion, that's a steal if all you need to do is replace the radiator.

@leonelchavajay8564

Жыл бұрын

Thanks for you video, thats a easy job i took everything out in like 45 minuts,, was a leak on top same as yours,, but now i went to every car parst store there is no radiator available, i had to order one from amazone ,espectra premium do you think it's a good radiator? 5start on you video

You in Florida

@F80__6MT

Жыл бұрын

I'm in California.

milage?

@F80__6MT

Жыл бұрын

This happened at 160k. Never changed as far as I know.

İşçilik iyi değil