Excellent. I could not have done this without this video.

@mrfxr1695

8 күн бұрын

Many thanks 👍 I'm glad you found this video helpful 🙂

Thanks, might be a few years ago, but just the info I needed 👍🏻

@mrfxr1695

3 ай бұрын

Thanks 👍

That electric connection metal wire just need to push in a bit and you are able to disconnect it! (And you will not loose it)

@mrfxr1695

Жыл бұрын

Thanks, it is true, your right I've tried that but it didn't want to come out so I opted to pull it out. Luckily I have found the clip

Thanks. Exactly what I needed to know with a concise description.

@mrfxr1695

2 жыл бұрын

Thanks John, All the best

Just what I needed! The grey clips 😉... Thanks Brother!

@mrfxr1695

2 жыл бұрын

You're welcome All the best👍

Thanks, great help and will save me a few bucks.

@mrfxr1695

Жыл бұрын

Cheers🙂👍

really helpful to know how to remove the pipe clips, thanks

@mrfxr1695

2 жыл бұрын

Cheers👍

Cheaper way, buy the Filter Housing tool. Remove the Housing, mark position on cap and housing to line up after replacing filter. Place housing in the Tool and unscrew the cap using Stilson of oil filter removal chain. Change filter then refit cap, line up the marks you made on Cap & Housing.

@mrfxr1695

Жыл бұрын

It is cheaper if it leaks only from lid and housings joint

@theangrygingerthebananavan4207

Жыл бұрын

@@mrfxr1695 agree. My friends leaked because it was over tightened.

@mrfxr1695

Жыл бұрын

@@theangrygingerthebananavan4207 I had one that leaked from fuel temperature sensor connector(located at top of the lid and can't be replaced on its own)

@bobbyfischer6786

Жыл бұрын

Mine has a very slow leak and i cant see where from, is the sensor at the top a common place to leak?

Hi New filter and o ring fitted with no leaks. My method was as follows. first hand tighten filter nut. Then mark housing, top and nut for reference. Now remove nut and smear inside of nut and outside of lid where they will connect with a little petroleum jelly, only a smear. Now tighten until all lines are aligned then with the filter protected from a hard floor ( i used a bit of carpet) I then held it down and tapped around on one of the ridges on the plastic nut with a small cold chisel until the line on the nut had passed the other markings by about 1.5 inches. Seems to have worked

@mrfxr1695

10 ай бұрын

I like your way, it will clearly prevent overtightening 👍🙂

Thank you 👍

@mrfxr1695

2 ай бұрын

Thanks 🙂👍

Thanks for this video great help 👍

@mrfxr1695

2 жыл бұрын

Glad it helped All the best

Thank you this is a great help

@mrfxr1695

2 жыл бұрын

Thanks👍

Great video. Thanks for sharing....

@mrfxr1695

3 ай бұрын

Thanks 👍🙂

Absolute hero

@mrfxr1695

2 жыл бұрын

Thank you

impecable muchas gracias por el video tutorial

@mrfxr1695

Жыл бұрын

gracias por las palabras de apoyo

Great that thanks, had 3 mechanics try to change the filter but looks like the housing is bust.

@mrfxr1695

Жыл бұрын

I hope it helps👍

It's people that over tighten the body trying to remove the ring making it oval , vauxhall fitted a very similar filter housing that similar it's the same paper filter, never heard of much problem with that filter housing

@mrfxr1695

Жыл бұрын

You're right about overtightening issue Thanks for sharing your experience 👍🙂

When removing filter from housing after the housing has been previously over tightened the o ring becomes oval and will not seal. I have ordered a new filter (not housing) that comes with new o ring so hoping this will stop leak

@mrfxr1695

10 ай бұрын

You're absolutely right there. My first filter housing leaked even after replacing seal. Second one leaked from fuel temperature sensor on the lid, that's why I had to replace it again 😞.

Thanks bro...is the same procesa to Ducato 2013?

@mrfxr1695

2 жыл бұрын

Thanks, yes it is It's same on all models since 2006

@Brumie-qq4dc

3 ай бұрын

Only on 1.9tdi

awesome

@mrfxr1695

Жыл бұрын

Thanks👍

Danke!!!!

@mrfxr1695

Жыл бұрын

Bitte!!! 🙂

Given the problems reported with this so often they should have been forced to issue a recall.

@mrfxr1695

2 жыл бұрын

I agree, but manufacturers only recall faults that are endangering life unfortunately

Hi there, followed the steps, but my van is now stalling after starting the engine. Do you have any advice? Really hope I don't need to take it to a garage!

@mrfxr1695

Жыл бұрын

Did you purge the air from the filter. You have to do it by running ignition on for 10 secs and than off and repeat few times as explained. By doing that electric fuel pump forces fuel through the system and pushes the air back to the fuel tank through return hose, you should not start engine during this process. Even if you have started engine after few stalls should be fine. Also did you checked all connections, it is not drawings air in through bad connection somewhere?

@joesnow739

Жыл бұрын

@@mrfxr1695 thanks for your reply. I repeated the first process a few times, still kept stalling. Checked connections everything looked fine, then primed one last time and decided to pump the accelerator a little whilst turning the engine on and it seems to of done the trick for now. Would that of helped force the air through the system? Cheers.

@mrfxr1695

Жыл бұрын

@@joesnow739 it could be, it seems you've done it

@joesnow739

Жыл бұрын

@@mrfxr1695 thanks alot for your video, helped to get the job done. Very thorough.

@mrfxr1695

Жыл бұрын

@@joesnow739 thank you All the best

Thanks

@mrfxr1695

Жыл бұрын

Cheers👍

My husband has attempted to change this filter himself this time after watching your video. Like you his bottom clip sprung out and he has lost it! Would you know where we can get another. 🤣

@mrfxr1695

2 жыл бұрын

try online (ebay perhaps) or contact fiat dealer, being a small wire clip I can't imagine to be expensive

@matsekberg

Жыл бұрын

You are supposed to push the clip towards the connector, not break it away

Whats the part number of this complete filter housing please?

@mrfxr1695

9 ай бұрын

Here is the info 🙂 Fits Citroen and Peugeot as well, see below For Fiat Ducato 06-18 Fuel Filter Housing Product Specification Full Set: Outer diameter [mm]: 114,4 Outlet Diameter [mm]: 10 Height [mm]: 233 Reference OE/OEM Number CITROEN: 1606450480, CITROEN: 190189, CITROEN: 190198, FIAT: 1362976080, FIAT: 1346387080, FIAT: 1352490080, PEUGEOT: 190189, PEUGEOT: 1606450480, PEUGEOT: 190198 Buyer Guide Fiat Ducato 130 Multijet 2.3 D 250_, 290_ Box 2287ccm 126HP 93KW (Diesel) 06-18 Fiat Ducato 130 Multijet 2.3 D 250_, 290_ Box 2287ccm 131HP 96KW (Diesel) 11-18 Fiat Ducato 130 Multijet 2.3 D 250_, 290_ Platform/Chassis 2287ccm 131HP 96KW (Diesel) 06-18 Fiat Ducato 130 Multijet 2.3 D 250_, 290_ Bus 2287ccm 131HP 96KW (Diesel) 11-18 Fiat Ducato 160 Multijet 3.0 D 250_, 290_ Bus 2999ccm 156HP 115KW (Diesel) 06-18 Fiat Ducato 120 Multijet 2.3 D 250 Bus 2287ccm 120HP 88KW (Diesel) 06-11 Fiat Ducato 120 Multijet 2.3 D 250 Platform/Chassis 2287ccm 120HP 88KW (Diesel) 06-11 Fiat Ducato 120 Multijet 2.3 D 4x4 250 Platform/Chassis 2287ccm 120HP 88KW (Diesel) 10-13 Fiat Ducato 120 Multijet 2.3 D 4x4 250 Box 2287ccm 120HP 88KW (Diesel) 10-13 Fiat Ducato 120 Multijet 2.3 D 250 Box 2287ccm 120HP 88KW (Diesel) 06-18 Fiat Ducato 150 Multijet 3.0 D 250 Bus 2999ccm 146HP 107KW (Diesel) 10-13 Fiat Ducato 160 Multijet 3.0 D 250 Bus 2999ccm 158HP 116KW (Diesel) 06-11 Fiat Ducato 160 Multijet 3.0 D 250 Box 2999ccm 158HP 116KW (Diesel) 06-11 Fiat Ducato 160 Multijet 3.0 D 250 Platform/Chassis 2999ccm 158HP 116KW (Diesel) 06-11

Tried replacing my fuel filter on Suzuki vitara very similar to this but it’s leaking fuel everywhere now

@mrfxr1695

3 ай бұрын

Leaking from hoses or filter housing?

The top fuel pipe will NOT disconnect, dammit!

@mrfxr1695

6 ай бұрын

Pay attention to light grey plastic clip. By releasing the clip it should come out

No model year in description

@mrfxr1695

Жыл бұрын

All X250 diesel models from 2007 onwards, Fiat Peugeot and Citroen

@offshoretomorrow3346

6 ай бұрын

Latest models have different connector clips, btw.

this is not real video tutorial

@mrfxr1695

6 ай бұрын

Thanks Happy New Year