How to Replace Front Wheel Bearing 88-02 Toyota Corolla
Автокөліктер мен көлік құралдары
Buy Now!
New Wheel Bearing Set from 1AAuto.com 1aau.to/ia/TKSHS00600
In this video, 1A Auto shows you how to remove and replace a failed, seized, or noisy front wheel bearing. The video is applicable to the 88, 89, 90, 91, 92, 93, 94, 95, 96, 97, 98, 99, 00, 01, 02, Toyota Corolla.
This process should be similar on the following vehicles:
1993 Toyota Corolla
1994 Toyota Corolla
1995 Toyota Corolla
1996 Toyota Corolla
1997 Toyota Corolla
🔧 List of tools used:
• Pry Bar 1aau.to/ooR/1AXAA00020
• 15mm Wrench 1aau.to/opD/1AXAA00010
• 19mm Wrench 1aau.to/opD/1AXAA00010
• 15mm Socket 1aau.to/oWo/1AXAA00015
• 17mm Socket 1aau.to/oWo/1AXAA00015
• 18mm Socket 1aau.to/owq/1AXAA00043
• 19mm Socket 1aau.to/owq/1AXAA00043
• 21mm Socket 1aau.to/owq/1AXAA00043
• 30mm Socket
• Press
• Pliers
• Snap Ring Pliers
• Ratchet 1aau.to/o29/1AXAA00016
• Socket Extensions 1aau.to/oWo/1AXAA00015
• Torque Wrench 1aau.to/oDW/1AXAA00044
• RTV
• Rust Penetrant
• Hammer 1aau.to/opZ/1AXAA00091
Subscribe: / @1aauto
Check out our playlist:
Toyota Corolla 1993-1997: • Toyota Corolla 1993-1997
For More Info visit us at 1aau.to/h/bJH/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
Пікірлер: 108
√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*
I’m gonna set my snap ring aside to ‘find’ it later as well 😂
@CapDanAddams
2 жыл бұрын
That was funny
Dude, thanks for the walkthrough, was having issues finding torque specs and you even included them! Much appreciated!
@1AAuto
3 жыл бұрын
+Cameron Gates Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
Just finished the job. Watched a little of the video then went and did that part so on and so on. The only thing I did different was my wheels are plain steel wheels with the open center, so I broke the 30mm axle nut first with the wheel still on and then removed it at the proper time. Thanks for the video.
This is one of the best "how to - videos" I have seen, you could become a great teacher If you wanted to. We just brought the PC to the garage and followed your lead step by step ( and added some red-necking where we didn´t have the proper tools ). A big thank you from Norway :)
@2012isRonPaul
2 жыл бұрын
this vid was maybe useful in 1968, because now you could use the actual slide hammer and bearing pullers to get a much easier result, plus you wouldnt even have to realign the whole axle with that method
@emmettturner9452
Жыл бұрын
@@2012isRonPaul The people who already have bearing pullers and slide hammers also already know how to do this. The people stuck trying to DIY for $$$ reasons will spend as much as they would paying a pro if they heave to buy fancy tools.
You should probably just become a auto mechanics teacher your awesome !!
@1AAuto
3 жыл бұрын
+Jonathan Calacuayo Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
Excellent video. Easy to understand and more importantly you can actually see what you are doing. I will be doing this to both sides of mine pretty soon. I think I can handle it now.
Very informative, just replaced both fronts in my corolla following this. Thanks 👍
This took a a couple days for me to do because I live in Minnesota so everything is basically corroded together and rusty like you wouldn't believe, that and I did this in my garage and I don't own a press so I had to pay 50 bucks for for a shop to do it for me, but other than that everything else went alright!
This video was super awesome, I will almost definitely be buying my bearing from 1aauto.
Extremely good explanation and properly procedures!!! Thanks
Wheels with a speed sensor will have a magnetic side to the wheel bearing. Make sure to install with the magnetic ring facing the correct direction.
O man. You did one hell of a job explaining every details. Nice job man. Really useful I really appreciated. A+
@1AAuto
4 жыл бұрын
+hmty2002407 Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com
@dwyer4000
11 ай бұрын
@1AAuto Don't you need to grease these bearings?
GREAT VIDE3O GUYS . very detailed and well shot .
I always break the axle nut loose before disassembling the brakes, this way it is already done for you and you don't need to rig up a pry bar to hold it, the tire and car weight does it for you.
@1AAuto
3 жыл бұрын
+mark collard Thanks for the feedback!
There’s lots of BONKS, WIGGLES, YOU DO YOU BOO BOO, and SPRITZ lol, keep up the great work Mr Lynn
Good job on the video, I'm doing this jib right now. It was fun to watch someone else do it lol
You are The Best out There , God Bless , 🙏 1A Auto parts for ever 🙏
Nice! Same principle on my old 88 Camry I'd imagine. Also, do you need to get the car aligned?
Which brand of Snap Ring Pliers are you using? Those long handles are great and just what I need!
Nice Job! Ridiculously complicated for just a wheel bearing (thanks Toyota Engineers) - I'd prefer a bolt on bearing any day!
Great teacher and vid. Thanks.
@1AAuto
3 жыл бұрын
+Kuznetskii Bassein Thanks for checking us out! 1AAuto.com
What size of old rotar was that you used on the press to get the hub out? I'm having trouble getting mine to sit nicely so I can press it out.
Great video....Thanks so much
@1AAuto
4 жыл бұрын
Alex Hernandez Thanks for watching!
Vericle....thx for the video
Thank you for you video
Very helpful my friend.
Great video!!!
my 2002 LE does not have snap ring. Need press.
Good Example of a RR ( Replace and Rove of a Wheel bearing assembly)
What is the part number for the oil seal? This is a great video!
17:05 **clip flies into next room** "Where gonna just set that aside so we can find it later"
Where do I mark the camber bolts?
17:04🤣 that's was funny
20:27 God dammit lol
What vehicle is that rotor for used for the press work?
Excellent!
That was great.I don't think that I could do any better than that.
Good mechanic
Thank you
Is this the reason my car bonks and wobbles at high and low speed not all the time only when I go on an uneven surface or when I go against the misalignment it starts to shake when I hit the brakes and slow down it stops I can go on the he flattest surface with no problem but give a little resistance or go on any in even pavement it wobbles like an earthquake
So that gold ring that you said was optional is truly optional? I cannot for the life of me get mine back in position on my 89 gts
Hey.. Nice video... Why is it important to mark the camber nets before removing
Is a 6 ton press strong enough for this job?
i wanna hear this guy say verricle for 10 hours straight
When removing the rotor and assembly I noticed on the passenger side there is a small sensor attached that views into the bearing assembly. What part is this?
@BLAZEPSI
3 жыл бұрын
ABS sensor?
Can I have my HF 20 ton press back
Wish my Celica had that kind of axle nut and cotter pin. Staked axle nuts are a pain in the ass.
@1AAuto
3 жыл бұрын
+Cody D Thanks for the feedback!
Are you supposed to click the torque twice to make sure that its correct or is that just a thing everyone does?
I barely noticed that's my friend's Corolla wagon lol, he has his own channel & I talk to him on Instagram
would be a lot easier with the slide hammer and bearing pullers tho?
Sir, I replaced my Switch window control, everthing is OK, easy to make with your explanation. But actually the driver windonw don´t works, the others works ok. What do you tihiks is happening ?? (I´m from Urugauy)
hello, i have a werid thing on my 01 corolla. the driver side only, the axle is on a diagonal angle pointing backwards. I dont know why, the wheel has little play at 3-9. wheel wobbles and axle wobbles too. Help please! nothing seems broken or making any weird noises. i just got the car a few weeks ago
@1AAuto
4 жыл бұрын
+Nando meh Thanks for checking us out! There could be multiple reasons why you are experiencing this issue. We recommend having a mechanic take a look.
How to replace front transmission driveshaft for 2004 celiac
@1AAuto
4 жыл бұрын
+wayne victorino We're always cycling through common cars. We'll add this repair to our list! 1AAuto.com
Do you happen to know what the average cost would be to have a shop do them?
@1AAuto
Жыл бұрын
+Sarah O'Brien We wouldn't be able to provide an average cost of this repair, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Good video, but what striked me as odd is that, when you tried to remove the race, you used blocks. you could have used a socket the that is a a little bit smaller diameter as the hub snout and a steel plate and you would have been able to save time from using a bunch of blocks an the air chisel
@1AAuto
4 жыл бұрын
+Rick Moises Thanks for the tip! We'll pass this info along to our production team.
@ThePandasian34
4 жыл бұрын
1A Auto Parts no problem! From mechanic to mechanic, just to let you know, a 27MM socket with do the trick perfectly!
@1AAuto
4 жыл бұрын
+Rick Moises Thanks!
Great video and so handsome
@reshreshshin874
3 жыл бұрын
🤡
Did no one else here him say “beerachle” instead of vehicle the whole video?
He always says veracal instead of vehicle lol funny
Always a good habit to clean the axle thread before you take off the axle nut
@1AAuto
3 жыл бұрын
+Brian Reese Thanks for the feedback!
Oke good
why do you take the whole spindle off the car? couldn't you do it with the spindle still on the car with a bearing puller kit?
How much does a job like that cost? Looks like a lot of time pressing bearings in and out.
@1AAuto
3 жыл бұрын
+Kenneth Hudson The cost can be anywhere from $130 to $220.
the bearing puller is installed incorrectly. the flat sides of the puller should be facing up. you see how everything is bent because he has it in backwards.
this has nothing to do with bearings but the part where he said you can whack yourself in the face with a tool or car part is true i know i had a fully assembled strut smack me in the forehead. and no it did not make me smarter it just made me know to not try and be a human cyborg and go fast on a car anymore.. so now since that day i take my time with the impala. and it runs better than ever. and yes i laughed a few minutes after i got done cussing the car out and the part for hitting me smack dead center in the forehead.
Show a good look at the barring, but nothing else.
No es un cubo de 30mm tiene que ser cubo de 32 mm fui y compre de 30mm y no le quedo.
How bout show how you got to this point. Theyre a few videos that are just wrong on the You Tube .
20:27 goddammit lol
lucky you, salt region cars arent better than this takes a lot of patience plus sometimes new bolts and nuts from Toyota self.
I'm gonna fix the wheeling bearing by myself It should be easy but after watching this I'm im like nah.
@AERuffy
2 жыл бұрын
It's easier if you just replace the entire hub assembly/knuckle from a junkyard. Pressing the bearing out/in is a pain and cost more in labor if you pay someone else. An entire assembly is as cheap as $20 as high as $100 at a junkyard. If you're not changing the entire knuckle then Using a hydraulic press like he is doing is also a pain. Get (buy or rent) a proper bearing puller and slide hammer kit. You can remove the hub assembly with a slide hammer puller $69) or a Screw Puller ($20-50). Then use a FWD bearing removal kit ($50-70) Or rent those tools at autozone/advanced/orielly.
Ahhh yes the press🥲
Veericle
I need a damn Press if I'm gonna be able to remove the bearing Race. It's not gonna be possible with a hammer and a race adapter 😂😅😫😣
I heard that 20:27🤣…
Good video, but you contaminated that new bearing big time drastically shortening it’s life span. You also had penetrant on the brake disc and pads. Use some spray brake parts cleaner, that’s what God invented it for!
you do you boo-boo ?!? ...regarding the thread locker comment at 38 mark
Thanks for vídeo but you talk to much
“Veerickle”
Wow that took such a long time to change the bearing I fell asleep
Thanks for the great video, but people today kill me with the safety bs.. beating it to death
@1AAuto
4 жыл бұрын
+MMGJ10 Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
Just sell the car!
Thats a NON ABS CAR TOO