How to Replace Driver's Side CV Axle 09-14 Chevy Traverse
Автокөліктер мен көлік құралдары
Buy Now!
New CV Axle Assembly from 1AAuto.com 1aau.to/ia/1AACV00171
1A Auto shows you how to repair, install, fix, change or replace broken, worn, or vibrating CV axles. This video is applicable to the 04 Chevy Traverse
This process should be similar on the following vehicles:
2009 Chevrolet Traverse
2010 Chevrolet Traverse
2011 Chevrolet Traverse
2012 Chevrolet Traverse
2013 Chevrolet Traverse
2014 Chevrolet Traverse
2015 Chevrolet Traverse
2016 Chevrolet Traverse
2017 Chevrolet Traverse
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/otB/1AXAA00013
• Pry Bar 1aau.to/ofz/1AXAA00020
• 21mm wrench
• 24mm Wrench
• 10mm Socket 1aau.to/oqu/1AXAA00017
• 24mm Socket
• 34mm Socket 1aau.to/oe/1AAST00004
• Torque Wrench 1aau.to/om2/1AXAA00044
• Brake Parts Cleaner
• Bungee Cord
• Transmission Fluid
• Floor Jack 1aau.to/of3/1AXAA00068
• Funnel 1aau.to/oad/1AXAA00310
• Hammer 1aau.to/ofw/1AXAA00091
• Jack Stands 1aau.to/ofx/1AXAA00065
• Rubber Mallet 1aau.to/oaj/1AXAA00413
Subscribe: / @1aauto
Check out our playlist:
2007-2016 GMC Acadia, Chevy Traverse, Buick Enclave: • 2007-2016 GMC Acadia, ...
CV Axle Replacement: • CV Axle Replacement
Chevy Auto Repair Videos: • Chevy Auto Repair Videos
For More Info visit us at 1aau.to/h/F9/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
Пікірлер: 58
√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*
For the alignment you should mark eccentric bolt before removing from the strut so you can put back where it was for wheel alignment. I also do it this way as opposed to removing ball joint unless of course your changing the ball joint.
THESE A1 AUTO GUYS ARE BEAST WELL EXPLAINED WELL RECORDED AND STREIGHT TO WUT WE WANNA KNOW.
Great video, good detailed procedure gives me confidence to try and do it myself thanks
JUST SAVED MYSELF LIKE $500 AND I ORDERD THE PARTS FROM 1AAUTO🤘🤘🤘🤘
@1AAuto
3 жыл бұрын
+Cesar Huerta 1915 Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
@CesarHuerta-ih7oj
3 жыл бұрын
@@1AAuto 👍👍👍👍
I may have missed it but do we have to have it aligned after the strut was taking off?
Very Good Video guys Thank You!
@1AAuto
5 жыл бұрын
+greggo502 Thank you!
how to change the rear CV axle in a 2011 Chevy traverse
Tell us the nut size as you point out the switch to ratchet on the axle nut as you do for the box wrenches, etc. Really nice comments during your work to describe your technique, like pulling straight so as to avoid seal damage, etc. By the way, using the clicker torque wrench, you might want to creep up on the torque a little bit. The release when you reach the set torque only has a bit of play. If you go too fast you might overshoot. Not a big deal but depends on your wrench I guess. Thanks for this video, I will buy my parts from you guys in the future!
@1AAuto
2 жыл бұрын
+Jason Koval Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
8:51 what if it didn't have one and what is it's purpose? Thank you in advance! Great channel 👍
@myriadtechrepair1191
2 жыл бұрын
I imagine the purpose of the washer is to keep the bearing from rubbing against the axle.
can this procedure works for a 2010 Buick enclave?
@thenakedcanadian13
3 жыл бұрын
I am going to be trying mine today as I did one on a 2003 Pontiac Sunfire...the only difference so far is the axle nut is a 33mm not 34 as there was too much play when the 34mm socket was on. I have 2010 CXL with 20" wheels.
@Wheelhouseprojects
3 жыл бұрын
Yes - Acadia, Traverse, Outlook end Enclave - all theta chassis vehicles
Can you spray the wheel speed sensor with penetrating fluid to help get it out easier ? Can you use brake parts cleaner on that sensor too - to clean it up ?
Good video, but the vehicle was not that old and rusted. Plus the lift helps a lot. They should do it like we have to. With jack stands and close to the ground on rusted cars.
@FleetTech97
3 жыл бұрын
It takes too long and harder to film that way. They are showing you what’s involved. The lift makes it easier but it doesn’t change any of the steps. Plus they used hand tools for the entire job. What more do you want ?
I forgot to install the washer on the new hub is it going to F anything up or noise issue.
Hello, I got a 2011 traverse. The seal on the housing that the cv axle goes in is leaking. What is that seal called?
Is it possible for a new 2019 Trax to have a CV axle go out
Should have put a new ABS Reluctor Ring in it at the same time. They don't last long.
Would this be pretty similar to 2012 GMC terrain?
@1AAuto
4 жыл бұрын
+Hill Hound We're always cycling through common cars. We'll add this repair to our list! 1AAuto.com
How long would you say it would take for one person doing this at their house without the benefit of a lift?
@turbotension
4 жыл бұрын
2-4 hours if everything comes part easy to nothing comes apart easy.
Question' I have 2012 sonic 120k miles a/t, the cv axle on the driver side is lose from the transmission side, is the problem the cv axle itself or bearing inside of the transmission?
@1AAuto
5 жыл бұрын
Thanks for checking us out! There could be multiple reasons why you're having this particular problem. We suggest taking your vehicle to a nearby reputable shop to identify the cause. +chem dog
@blackz-nc1sz
5 жыл бұрын
Did you find the cause?
0:29 the tire looks fine on that side ha ha
No need for realignment after detaching the strut?
@treetopfliers
3 жыл бұрын
Yes.
How do i know if the axel needs replacement? The covers look fine, like the one in the video, they are sealed and they look fine, but i am getting a alight "clunk" only when i turn my steering wheel.... No noice when i go ober bumps. All bushings look fine, all new struts.
@myriadtechrepair1191
2 жыл бұрын
You're going to want to first make sure all of the fasteners are torqued properly on the control arms, tie rod end, ball joints, sway bar end link, and axle. If nothing is loose, the noise could be the axle but it could also be the steering rack. Much easier to replace the axle, so if you're doing the work yourself it's the better bet.
Generally I place a flat blade screwdriver in the grooves of the rotor to take the axle nut off like that
@1AAuto
2 жыл бұрын
+Billy Sanders Thanks for the tip!
@billysanders5353
2 жыл бұрын
@@1AAuto yes sir and yall are the best online instructor's love you all videos very much
Why not use some anti seize compound on the splines?
is it still a 34 mm for a 09 chevy impala
@1AAuto
4 жыл бұрын
+BeepBeepImACar1 Yes it is! 1aauto.com
Question, how can i replace the abs sensor, i broke it trying to pull it out
@joshromero380
3 жыл бұрын
Same vehicle
@1AAuto
3 жыл бұрын
+Josue Obdualdo Romero We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-1AAuto-c
Is it tranny oil or transfer case fluid?
👍🏻👍🏻👍🏻
@1AAuto
9 ай бұрын
+Mr. M. Dee Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
I know we all work differently and I shouldn’t criticize but the tools you’re using makes me get a headache. How do you have the patience for that?
why dont you use an impact on any of your videos? Nobody uses breaker bars anymore.
@1AAuto
4 жыл бұрын
+14GMCLMLJEFF Thanks for the question! We try to use tools that most customers would have on hand at home to do their own repairs.
@jasonkoval4750
2 жыл бұрын
@@1AAuto Yeah, like lifts
Do you actually need the washer and if you don’t have it any longer what’s it actually called so I could get it
@h2onerd271
2 жыл бұрын
the real question is why they don't just provide a new one with the axle?
Your video turns black can't anything but pitch black
@1AAuto
5 жыл бұрын
Thanks for checking us out! We have reviewed the video on KZread and we found no issues with it displaying a black screen. You may want to try a new browser or clearing your cache and cookies. Hope this helps you out! +Cesar Astorga
@sharonmitchell1554
3 жыл бұрын
Al@@1AAuto