IMPORTANT! 1:00 This is not special tool! This is simple valve stem cap, usually founded on bicycles. If you don't have this type of cap, use small needle nose pliers, or cut slot in nail or something similar. Thank You!

@ED-es2qv

Жыл бұрын

Order a pack of those caps from Amazon and put one on every vehicle you have, so you always have one handy. The tire store always steals mine, and they hit rocks and get damaged, so I put one only on the jeep spare.

Very good video, but people should be aware that motor oil will harm the tyre valve. The tyre valve is a mix of rubber and neoprene which can be harmed over time by oil. Would strongly recommend the use of soapy water which is just as effective & dries out giving a seal that will last without any harmful effects.

@leonnygren2189

Ай бұрын

Im glad you mentolend that

Never use oil! Dish soap.

@wildestcowboy2668

2 жыл бұрын

Why?

@NTSRFR4

2 жыл бұрын

@@wildestcowboy2668 Petroleum oil can break down the rubber over time. Most use soap or silicone grease.

@wildestcowboy2668

2 жыл бұрын

@@NTSRFR4 TKS Boss

@rockroll9513

8 ай бұрын

@@mail-qh2qc 😂😂😂

Great video. Loved the nail /cap hack

Top video, many thanks from me in Edinburgh, job done. My purchases - valve stems and a Silverline make 4 way tyre valve repair tool to loosen/tighten the tyre valve and to attach to the new valve stem to pull it into place: Total cost £3. I already had a cheap tyre inflation compressor that runs from the 12v socket in the car. Issues - all went well until I tried to rebead the tyre but couldn't get air in fast enough to reseat it. Solution - raised up the side of the tyre opposite the valve 6 inches so that the wheel was clear of the ground. Then started the compressor and stood on the wheel on the unbeaded section and bounced gently up and down pushing the wheel downwards into place. As I did this the tyre quickly started to take air and popped into place. P.S. For those considering using the alternative replacement method using the tool that punches a new valve in without having to unbead the tyre. It will work if you have steel wheels but i'm not if you have alloys due to the access hole for the valve being recessed.

@Work_G

3 жыл бұрын

Thank You!

Oil attacks rubber. Use soapy water. This is probably why the first valve stem was leaking.

@Work_G

3 жыл бұрын

You are probably right but I can assure you, this small amount did not do any damage and that wheel holds air till today. And old stem is probably old as car

Your the best!!! I always get help from KZread, but did not think there was something for this. Thank you!

@Work_G

3 ай бұрын

Really appreciate it. Also I have video on how to remove valve core in 3 different ways without special tool if you interested: kzread.info/dash/bejne/lYllxaavd8bdfqQ.html

Thanks, you just saved me from buying that little 4 way tool that is used in so many other videos on this topic. Great video.

@Work_G

3 жыл бұрын

Thank You, glad it helped

@Ccookkiieee

3 жыл бұрын

I just bought 1 from AutoZone for $1.99.

What is that heavenly hypnotic music?? It’s got me standing up and shimmying my hips back and forth like I am one with the beat! " MARTHA come here! " something’s happening!!!!!

@antonmk1244

4 ай бұрын

I can hear Prince 's voice in it, no?

I liked that you checked your work for leaks before just putting the tire on, getting on the Autobahn with the car top down and a few girls finding out the HARD way.

@Work_G

5 жыл бұрын

Got to be sure :D Thanks

The wheel looks like it has seen better days !

Petroleum products eat rubber. Using soap on the new valve stem won't damage it. LOTS of soap.

@youtubebitchcenter1463

5 жыл бұрын

And K- Y jelly.....if you have any extra laying around 😬

@infidel66687

4 жыл бұрын

Vegetable oil works good too. Just no petrol oil.

@absbse

4 жыл бұрын

Can I use multi purpose grease instead of oil?

@sirich7751

3 жыл бұрын

Corry R thinking the same. Rubber and petroleum products don’t mix

@beachbums2008

3 жыл бұрын

Looks like you put black bead sealer between the tire and rim before you seated the tire with air pressure. Is that correct?

Thanks! That helped!

Thanks. Perfect just what I was looking for.

@Work_G

Жыл бұрын

Great to hear!

Great tip thanks!

Amazing thanks for the video :)

@Work_G

5 жыл бұрын

No problem!

I just subscribed Bro’. This is really good info and the tune is pretty cool too.

@Work_G

6 жыл бұрын

Thanks a lot, I appreciate it

Never use oil, it damage the rubbers.Use soap instead of oil.

Thank you. Didn't know it was that simple.

@Work_G

2 жыл бұрын

You're welcome!

A side note, since there's no actual sound there... A hissing sound and quite strange smell (to some) will be present when you remove the valve core. Another is, a popping sound of the tire when it seats right to the rim (sometimes very loud) which might surprise some peopl who knows nothing about what they're doing 😁. Good info here. Keep it up eh

@Work_G

3 жыл бұрын

Many thanks for addition

@twincam825

2 жыл бұрын

If they don't what they are doing take it have it done.

Great video, very clear. Not a fan of the music, muted it.

@Work_G

3 жыл бұрын

Thanks!

Absolutely perfect video. Could use a bit of text but other then that it's perfect

@Work_G

5 жыл бұрын

Thank you very much:)

The video I was looking for. Thanks man.

@Work_G

2 жыл бұрын

I am glad that it helped!

Don't use motor oil, it will break down the rubber. Use dish soap, or soapy water, or even just water.

@Work_G

3 жыл бұрын

It is good advice in theory but in my practice nothing happened

Thanx 👍👍👍

Este vídeo si que sabe el como no dañar la válvula y usar el saca pivote felicidades

Talk about improvising, Nice

That's a real Rube Goldberg bead breaker!

Helpful video but the music BLOWS!

Oil and rubber don't mix well

Thank you was veary helpful!

@Work_G

3 жыл бұрын

Glad it was helpful!

My man, the nail is genius

@boburyusupov9487

4 жыл бұрын

You can say that he nailed the idea lol

Silicone grease in lieu of motor oil

Awesome video dude!!! Get tool kit at Walmart Canada Okanagan. Oddly they don’t have valve stems, one of the boys in automotive department gave me one thanx to all...

@Work_G

6 жыл бұрын

Thanks :)

Great job! Thanks for the video! but would the oil eat the rubber? Maybe better to use soapy water like dishwashing liquid.

@Work_G

5 жыл бұрын

Thank you :) Little of oil is fine it wont do anything bad for rubber but sure you can use any lube or nothing, that is just to make easier slip in without damaging. (already 8 months after this job and Its all god for me, no leaks)

@maskedavenger2578

2 жыл бұрын

Never use dishwashing liquid ,it contains salt & will corrode alloy & chrome steel wheel rims .& some oils will attack various rubber & man made materials . Just use mild hand wash liquid ,that contains no bad stuff to corrode or rot your wheels or rubber valve stems .

@oscargrouch7962

2 жыл бұрын

Waterproof silicone plumber grease is made to grease and seal rubber o-rings and rubber faucet washers. It will also work with rubber tire valve stems.

Wow this is a awesome tutorial !!!!❤️ Blessings and more blessings to you and your family in Jesus name Amen

@Work_G

Жыл бұрын

Thank you

Best film of the genre

@Work_G

Жыл бұрын

Thanks

The best rustproof oil is Ballistol

Like the music u used in this video now I never go to the garage again

Bonne vidéo !!!!!!

Great vid, can't you push the stem out instead of cutting it? You push the new one in could it work the opposite way for removal?

@Work_G

2 жыл бұрын

Thanks, probably you can but that should be difficult and either way it shouldn't be reused

Good IF you don't have the right tools. With a valve change tool kit (less than 20.00 USD) you can do this without removing the tire and in less than 2 minutes. Oddly, very hard to buy a good one in the US or Canada. I ordered my from the UK through Ebay.

@Work_G

6 жыл бұрын

Yes that is all point, when you need fast at home and don't have tools. Otherwise just take it to tire shop it is cheap.

@daverobertson8947

6 жыл бұрын

istvan meissler Walmart they have them in Canada . Bought one yesterday

I've used the base on a bumper jack to break tires down before. Now days bumper jacks and vehicles you can raise with one are getting hard to find.

@Work_G

4 жыл бұрын

True

Ended up using some good old spit and my hardwood nail extracting thumb...😂

Can I do this when my tires have a TPMS ? I wouldn’t wanna damage the sensor if I do this. One of my tires keeps loosing air. Thanks

@Work_G

5 жыл бұрын

You can, but there is whole different mechanism, and different valve stem, just search picture how looks TPMS, it's quite complicated.

Ok. Now you can clean 🧽 the damn rim with soap 🧼 and water 💧.

The tire store seems to use soapy water to seat the bead. Hard tire users can spin a tire on the bead, or peel a bead that otherwise would have held if you leave oil on it. Great video, thanks. I’m going to use your pliers trick but substituting soapy water for oil.

@Work_G

Жыл бұрын

Good point 👍 But after driving many miles I can assure you that the oil has not caused any problems for me.

@seanmckay3392

Жыл бұрын

I use starting fluid and fire to bead my tires

Nods head to beat😎

time for some new rims

Oh ok. Let me try this again.

I had great difficulty inflating . really hard to push the tyre beading over the vaulve area, Luckly I had tyre leavers.

@beachbums2008

3 жыл бұрын

Use a ratchet strap around the tire to compress the tire to conform tight to the rim. Ad are high volume with out vale core untill tire seats against rim. Then take off rachet strap and fill tire to correct air pressure

@TralfazConstruction

2 жыл бұрын

@@beachbums2008 Thank you for that excellent pointer. I'd seen that done over fifty-five years ago and had actually forgotten that.

Oil on rubber is an absolute no no rite off the bat, silicone spraywould be more appropriate thing, of dishsoap..

Whats the tool at 3:00 that you used to pull the stem?

@Work_G

Жыл бұрын

Metal valve stem cap with hole and nail poked through

Just the kind of video I like: Not a bunch of talking, just showing what to do with a little chill background music. Thanks man.

@Work_G

Жыл бұрын

I appreciate that!

Are those bubbles coming from that newly installed valve stem?

@Work_G

3 жыл бұрын

No

Problem is you need a compressor that's capable of moving a lot of air faster then your normal air pump in order to seat the tire back to the rim.... Which most people don't have either

@johnbattista9519

5 жыл бұрын

To solve that, take a long enough rope and a long bar to make a turnaquett around the center of the tire.... a small compressor is just fine. I’ve replaced many valve stems this way, piece of cake.

@fuelz7124

4 жыл бұрын

This is a how to change a valve stem video..not about seating a bead, or airing up a tire and re installing...etc. stop being a hater.

@judgenap

4 жыл бұрын

@@johnbattista9519 I had great difficulty inflating . realy hard to push the tyre beading over the vaulve area, Luckly i had tyre leavers. thanks for your idea.

@johnbattista9519

4 жыл бұрын

judgenap , glad I could help. I was never a fan of using WD-40 and a match. Using a long rope around the centerline of the tire always worked to close the gap of the bead and rim to start the initial inflation.

@rancon265

4 жыл бұрын

Ratchet strap.

Should of pulled stem with vice grip pliers.

what is the part you used to pull the valve stem?

@Work_G

5 жыл бұрын

To unscrew valve itself I used bike valve stem cap, it is just screwed on other broken valve stem. But you can use small needle nose pliers or cut slot in bolt.

@johnbattista9519

5 жыл бұрын

Ben Dont looked like a cap drilled for a nail... for $3.99 just buy the puller.. pops the stems in less than a second.

Now, show us how to install stem without separating the tire from wheel?

@monkmodemalik8225

4 жыл бұрын

You cant

When assemble tire by fire flash, is better assemble stem afterward because otherwise vacuum pull tire off, if it is in place. Wire for pull it in hole works.

@Work_G

4 жыл бұрын

In this video I didn't used fire to inflate tyre.

@jarikinnunen1718

4 жыл бұрын

@@Work_G But if someone doing so, advice is useful.

I appreciate your time and effort, but 7 just convinced me thar it is worth paying $5 for the tire technician to fix this for me

@Work_G

4 жыл бұрын

I agree with you, in most of cases its better to trust this job for professional!

USE AN ELECTRIC SCREWDRIVER WITH NO ATTACHMENT, HIGH SETTING, HOLD THE STEM AND VOILÀ!

Helpful video but the music was annoying

@Work_G

4 жыл бұрын

Thank you for the feedback!

Sometimes the simplest things escape my mind. Like putting a little boat through the cap🤦

@robertjahrling1877

4 жыл бұрын

BOLT

never put motor oil on rubber

Jais jamais réussi même en regardant la vidéo

Can you just remove the gold tip?

@Work_G

4 жыл бұрын

No, if I understand your question right. There 3 pieces - cap, inside piece (valve) and whole rubber stem with threads (that gold tip)

dope ass music

Ya that would be a tool

@anthonym7133

4 жыл бұрын

Exactly

I used a a bike pump and pulled and some Vaseline

@Work_G

Жыл бұрын

Most important thing is that it worked, good job ✊

Oil on rubber are you mad? Valve and tyre? Soap, washing liquid, etc !!!!

@Work_G

4 жыл бұрын

Relax, that small amount will never ever do anything bad for rubber. I can say that after 2 years it still holds air tight

Are you supposed to use GM oil on that BMW rim? WARRANTY VOID

@Work_G

4 жыл бұрын

I used what I had, soap works fine too

@anotherbeard667

4 жыл бұрын

@@Work_G i appreciate the video, it saved me a few bucks!

@Work_G

4 жыл бұрын

@@anotherbeard667 I am happy that this helped

I wrestled my tire over the rim with 2 big screw drivers and alot of curse words, would not recommend lmao

What’s the size

@Work_G

Жыл бұрын

If you mean rim size its 15

That thing you're screwing is actually a special tool

@Work_G

3 жыл бұрын

That is valve stem cap, usually founded on bicycles. Othervise use small needle nose pliers, or cut slot in nail or something similar.

@ED-es2qv

Жыл бұрын

That’s technically true, but nitpicking because any sacrificial thing you can thread on there would work. If you can inflate and deflate tires in your driveway, you probably have several options.

@consciousobjector2507

4 ай бұрын

um no it's not.

That is definitely a special tool

Song?

@Work_G

6 жыл бұрын

Check description, link is there in bottom :)

I think the hardest part is removing the rim from the tire.

@Work_G

2 жыл бұрын

True

Motor oil will destroy that valve stem in a year, use soapy water

@Work_G

2 жыл бұрын

May be in theory, mine is fine ~ 2 years

i kno a guy who ca push them in from the front by hand

OIL CAN RUIN THE RUBBER VALVE STEM ITS BETTER TO USE A SOAPY WATER TO LUBE THE RUBBER VALVE STEM

that oil you put on there gets inside the rubber, in the winter the salt will force it out and you will have a cracked valve stem again, save that other one from the pack lol

@Work_G

Жыл бұрын

But in real life that didn't caused any issues for a few years of daily driving

Top Tip! don´t use that brick and vise on your Lamborghini rims!

@Work_G

5 жыл бұрын

Good one :D I guess if can afford lambo can afford visits to service :D

Yeah no special tool! Only simple press tool! LOL

@Work_G

5 жыл бұрын

That "special tool" as you call is bike valve stem CAP. I wouldn't call that special because almost everybody have that and if not it cost cents. You can unscrew that valve with needle nose pliers or buy real special tool which use tyres shops both ways you spend much more than I show in this video. Be realistic in YT there is mutch more clickbait...

@bballkid7409

5 жыл бұрын

GetWork he was talking about the press used to break the bead of the tire im pretty sure

@Work_G

5 жыл бұрын

​@@bballkid7409 pfff :D To break the bead that is simple brick and emergency car jack, which can be find in almost every car trunk :D

Maybe different music would be better

@Work_G

5 ай бұрын

Probably 🙆‍♂

“Without special tools” - uses valve stem removal tool. Most people would consider that a special tool and wouldn’t have it around.

@Work_G

3 жыл бұрын

Read pinned comment dude...

@bamseals4126

2 жыл бұрын

Thank you

Wash the damn rim.

Music weird

At 3:54 in your video

@Work_G

3 жыл бұрын

What?

Says you don’t need special tools but proceeds to pull out special tools 😂

@Work_G

5 жыл бұрын

In this video I didn't use any of special valve stem removal tools that tyres shops use....

@fuelz7124

4 жыл бұрын

So a pair of pliers and a valve stem remover are "special" tools to you ??

No special tools huh? Ugh what about the tool you used to break the bead? I don't even know what that was that you used. Therefore, to me it looks like a special tool. Especially considering i don't know the name or how to even use it properly.

@Work_G

2 жыл бұрын

That was brick with simple emergency jack which can be found in almost any car... And if you dont imagine how to use basic tools you probably shouldn't work on your car.

This definitely doesn't work with a plastic valve stem. I tried it in a pull the nail right out

@Work_G

2 жыл бұрын

You can pull it with pliers, but be careful don't damage threads or rubber part

Motor oil eats rubber bruh 😂

@Work_G

10 күн бұрын

In theory yes, but in this application 5+ years still no issues

Didn’t work. Tore the stem in half.

@Work_G

3 жыл бұрын

How?

Nice video on the how to. Crappy music though. Would much rather listen to Truman Capote narrate how to do this job than listen to that atrocious "music".

@Work_G

4 жыл бұрын

Thank you. You can always press mute.

Just pony up a few bucks and buy the cheap kit from Amazon . (AME 51025) Quick Valve Change Kit And stop the madness 😠