Thank you, I’ve already forgotten what I have to do.

@yeeyeecraig1581

9 ай бұрын

Got to watch while you do it

i use the old cable to pull the new one thru, leaving the tank on

Very well explained ! Good quality video, thanks for the tips !

this was lot easier than it looks and i didnt have to remove the tank

@josephtonellato7727

2 жыл бұрын

Same

Good video very specific and informative

Thanks man. Cheers from BC, Vancouver

@mxch1082

2 жыл бұрын

@604Beats Deltaaaaaaaaaa

Perfect explanation.

Awesome video you earned more than 2,5k vieuws.

Thanks Great explanation

pretty good explanation

I have adjusted the cable on my vintage 1971 Kawasaki Trail Boss 100 (3300 original miles) but it still doesn't disengage the clutch when putting it in gear? Your video mentioned other parts that might need replacing? Any guesses as to my problem? Thanks!

how do i know what kind of measurements to have on the cable?

What clutch cable do I need for a trailmaster tm31x 250cc?

Just put mine in a while Ago but it’s way harder to pull compared to when I had it before

Is it same concept as on Yamaha 250 Exciter

are some cables pre lubed by factory?

Thank you!!!

@rmatvmc

5 ай бұрын

You're welcome! 👍

My clutch lever is not engaging the clutch even though the cable is moving, help

I've replaced my cable with a motion pro and routed it In factory position and when bars are to the left no free play bars to the right alot ot free play

@kayn3634

5 жыл бұрын

Ryan Wojciechowicz you might have routed it wrong

when should i change my clutch cable?? aside from it is broken of course

@jmcgrath3584

6 жыл бұрын

Before it breaks better than after.

Do you have to lube it? I don't have oil for that wd40 works for that or not?

@rmatvmc

6 жыл бұрын

Lubing your cables is good practice and can prolong the life and sliding action. Check out our cable lubes we sell here: www.rockymountainatvmc.com/Sales/834/How-To-Replace-A-Dirt-Bike-Clutch-Cable . I would recommend you pick up some. It's not very expensive.

@messiona

3 жыл бұрын

WD40 isn’t lube

What are the tools I need? I'm going to the store today or tomorrow so I can connect my clutch myself.

@rmatvmc

2 жыл бұрын

We show the tools we used to complete this job at 1:20 in this video.

I am just trying to see if there is a difference between a brake and clutch cable

@rmatvmc

4 жыл бұрын

I'm not sure what you mean but brake and clutch cables are different. We have a video showing how to install brake lines that I'll post a link to below: kzread.info/dash/bejne/npaVy6-idb3XZaw.html

@milesbeck9444

4 жыл бұрын

Well im in deep shit I ordered a clutch cable thinking it was a brake cable for $30

how important is it to lube up your cable, i dont want to take it all apart again.

I have a old Chinese bike not sure what routing should be done. Was replaced before but porly and I feel like that’s Not the right way to rout it. Clutch still isn’t fitting it’s hot out and I’m grumpy 😅

what if the new cable is still too tight on the loosest setting on the adjuster by the engine and by the clutch lever? i bought the same cable for my model bike

@ghostlystatue7933

3 жыл бұрын

Same

@ghostlystatue7933

3 жыл бұрын

Did you ever figure out to fix it?

@youngb32by

3 жыл бұрын

@@ghostlystatue7933 I just took out the inner ring by the adjuster by the clutch lever which gave me a few extra mm to work with.Then tightened it all the way then adjusted it by the engine. If that makes any sense

My clutch cable snapped a few days ago, I’m waiting on a new one but when I pull in the where the clutch cable attaches to it doesn’t actually engage the clutch. Should I be concerned?

@rmatvmc

2 жыл бұрын

Are you talking about the actuating arm that's on the engine? If the clutch worked before the cable broke, it should work again as soon as you get the new cable on. kzread.info/dash/bejne/a6dsqNN-crK0nM4.html -Charles

How can i fix a stuck kick start? On a honda trx fourtrax 1986

@travisbellew7485

3 жыл бұрын

by rebuilding your engine

Mine is on the side like mentioned. Is there a reason behind doing below first, lever last? I ask because that's how you explained. Just wanted to be sure

@rmatvmc

8 ай бұрын

Adjusting the clutch side first allows you to make bigger adjustments so that you can do your fine tuning on the lever side to get the correct free play and to make future adjustments when components wear.

@danielpatrick368

8 ай бұрын

@@rmatvmc oh yeah, i had planned on putting it on* that way first..

What happens if it doesnt help

Is it normal for my clutch lever to be loose (bout an inch) until i pull it in? First time fixing a bike!

@alexchapman4747

5 жыл бұрын

That’s just adjustment mate

@alexchapman4747

5 жыл бұрын

You might have to tighten it up a little bit

@Blake-pu3xc

5 жыл бұрын

@@alexchapman4747 Yep tightening it up sure did the trick. Thanks

Greeting frome kx80/1998 from holland

I got a cr 250 and when I put it in first gear it stalls with the clutch in

@alexchapman4747

5 жыл бұрын

Castaways_fishing that’s just the clutch being too tight but it is ok, you might want to make it a little more slack, until you can shift it into gear and not stall

I have a question, my clutch hangs freely, like if I pull it in it stays and I have to manually push it out, and the clutch just doesn’t work itself, what could be the problem?

@LukeTheMasterOfNothing

2 жыл бұрын

I would assume you have springs installed in the clutch basket, so maybe your rod isn't in correctly or have no rod at all?

When I pull in my clutch on my kx125 in 1st gear u can't push it but when it's running it's fine

@450_Chriz

6 жыл бұрын

normal when engine is cold

@sendit9803

6 жыл бұрын

dayne washere need new clutch plates man

@jmcgrath3584

6 жыл бұрын

My new bike came with clutch drag. It seems pretty normal. New plates could get rid of it though. I heard roughing up surfaces of the plain plates helps them hold oil and reduces clutch drag.

@tannertyrik6251

6 жыл бұрын

It’s because it’s a wet clutch and the motor got to be running for the clutch to engage

My rm85 clutch cable was super easy I didn't even need tools

This does not work. I tried it my bike, and it does not turn whatsoever to even get to it and for the break that’s already set up for it. It doesn’t pull out.

I’m inches away from where my clutch should be. Wrong cable?

How do Ik what size to get

@rmatvmc

2 жыл бұрын

Enter your dirt bike's year, make and model on our website to ensure you get the correct clutch cable. Just click the link below, enter your bikes information in the drop down boxes and then all the parts that come up will fit your bike. www.rockymountainatvmc.com/

Sponsored by tusk 🤔

Is it an inside joke at the office when you guys say “ Rocky Mountain ATV “N”C” ?

Mine frayed in half

Just a curious bloke

Handle barst 🤨

Clutch.... cable....?

A luber tool? Fergaddsakes.

I love how it doesn’t show him install the cable at the clutch HAHAH like wtf man?

Theses guys always want to sell us something

@Aglow37

4 жыл бұрын

That’s what I’m saying EVERY single tutorial I watch at some point has some magic tool or something that you “need” then I gotta figure out a way to do it by myself😂

Great video thanks. But the whole... Keep Turning your wrenches at the end made me cringe a little.

What's a clutch cable? Talk about living with old tech.

@jmcgrath3584

6 жыл бұрын

It controls the engagement of the clutch without leaking fluid or air bubbles impacting it.