HOW TO REPAIR THE AC AND RADIO CONTROL KNOBS ON A NISSAN R35 GTR
Автокөліктер мен көлік құралдары
Most people who own an R35 GT-R seem to have the same issue, the radio and ac control knobs do not work as they should. When you turn them down they go up, turn them up they go down, turn them one click it jumps five, turn it fifteen clicks and it only goes one.
In this video, I show you how to fix your ac and radio control knobs on your Nissan GTR so that they work as they should.
_________________________________________________________________________________________________
If you are interested in supporting the channel, check out the JD Archer Shop for apparel like what I wear in the videos. jdarcher.bigcartel.com _________________________________________________________________________________________________
If you want to purchase any of the equipment used in this episode, click the links below.
Video Gear
GoPro Hero 9: amzn.to/3kMUYre
GoPro Media Mod: amzn.to/2Wjr6cz
Rode Wireless Go: amzn.to/3kNV5D5
Tools
Craftsman Tools (450 Piece): amzn.to/3AK0yzw
Craftsman Tools (320 Piece): amzn.to/3DXJ6cX
Craftsman Tools (230 Piece): amzn.to/3mOBp1C
Interior Trim Removal Tools: amzn.to/3kX3mrd
WD-40: amzn.to/3kX3mrd
_________________________________________________________________________________________________
Links to Similar and Related Videos:
HOW TO INSTALL AEM FUEL PUMPS AND VISCONTI FUEL FILTERS IN A NISSAN R35 GTR
• HOW TO INSTALL AEM FUE...
HOW TO REPLACE THE LEDS IN THE R SWITCHES OF A NISSAN R35 GTR
• HOW TO REPLACE THE LED...
INSTALLING A CT CARBON NISMO WING ON A NISSAN R35 GTR AND REVIEW OF CT CARBON NISMO WING
• INSTALLING A CT CARBON...
INSTALLING A BRAKE BRACE ON MY NISSAN R35 GTR
• INSTALLING A BRAKE BRA...
CARBON FIBER WRAPPING THE CENTER CONSOLE OF MY NISSAN R35 GTR (HOW TO)
• CARBON FIBER WRAPPING ...
INSTALLING NEW FENDERS ON MY NISSAN R35 GTR • INSTALLING NEW FENDERS...
NISSAN R35 GT-R MAINTINANCE: HOW TO CHANGE THE BRAKES, ROTORS AND PADS PART 1
• NISSAN R35 GT-R MAINTI...
NISSAN R35 GTR MAINTINANCE: HOW TO INSTALL BRAKE ROTORS, PADS AND STEEL BRAIDED LINES PART 2
• NISSAN R35 GTR MAINTIN...
FIRST WORK DONE ON THE R35 NISSAN GT-R: MAINTINANCE OIL CHANGE
• FIRST WORK DONE ON THE...
MAINTINANCE ON A NISSAN R35 GTR: SPARK PLUGS
• MAINTINANCE ON A NISSA... ______________________________________________________________________________________________
You can follow me on: Instagram:@ j_d_archer
Tik Tok: www.tiktok.com/@jd_archer
Twitter: @jd_archer
Or I have a facebook page: / jdarchervlog _____________________________________________________________________________________________
I have now become an affiliate of Chemical Guys. If you want to support the channel as well as get some great products for cleaning you car, please click the link below.
www.tkqlhce.com/click-1002666... ______________________________________________________________________________________________
Music provided by www.bensound.com and Epidemic Sound ______________________________________________________________________________________________
#NISSAN #R35 #GTR
Пікірлер: 30
Good advice and well presented.
@JDArcher
Жыл бұрын
Thank you
Thanks for the video. I went ahead and did mine this weekend and got the same results. The volume works better but not 100%
@JDArcher
Жыл бұрын
Mine has gotten better over time. I think the thing is I don't adjust volume that often
Thank you very much, I was a bit incredulous but I tried it today. Easy to do and it works. Finally, after 5 years just using the steering wheel button🥹
@JDArcher
5 ай бұрын
Glad it helped
This happens because the potentiometers age and get a patina on the base part inside, that prevents contact. If yours keeps going bad again and you want to repair permanently then desolder each one with an smd rework station heat gun like an 858D/868D with small nozzle (NOT a normal heat gun), be sure to protect nearby components like LEDS with foil. With each one removed from the board carefully open the potentiometer by lifting the 4 lugs underneath, then lift the frame off. When you separate the potentiometers be careful not to lose the little button press rubber part or bend the little contact springs, this is best done on a light tile floor in case bits fall out. You then gently wipe around the metal base contacts with a tiny bit of 1200 sand paper. Reassemble potentiometer with pliers, check it works then solder each one to the board (from memory the volume one is different to the others). I recommend using solder suck or wick to get solder flat so potentiometer sits flush on board, then hold down whilst adding solder to each leg, don't forget to solder the sides after too. It's quite fiddly and not without risk but it is essentially a free permanent repair that makes it as good as new and doesn't require new potentiometers; providing you have some solder skills and don't f**k it up of course 😊
@JDArcher
Жыл бұрын
Great info. Thank you
@rw00219
Жыл бұрын
It's also possible to use new Panasonic EVE-UPCAH516B potentiometers from DigiKey as donors to rebuild your existing ones. You take just the base from the new one and reuse all other components of your existing. Although this should not be necessary if you're careful with previous method.
i actually just removed the knob and used a ear q tip soaked in alcohol and tried to soak the metal knobs as much as possible, it did fix the issue but im not sure how long that fix will last, i did this because my xbox elite controller was having a bad bumper issue and this is actually a fix for a non responsive bumper
@JDArcher
Жыл бұрын
I took it all the way out to also check the board
Any videos removing the lower unit?
@JDArcher
Жыл бұрын
Not yet as I haven't had to do it. However I imagine it about be about 4 screws, then the electrical in the back
Never seen WD40 used on or around circuit boards. Wonder if there are any longer term undesirable side effects. I would think electronic cleaner would be a better choice because it will evaporate and not leave an oily residue. I think WD40 is fish oil based and I'm not an expert, but I don't see any electronics people using fish oil or WD40 on circuit boards. Anybody have any feedback?
@JDArcher
7 ай бұрын
That's why I wiped up the board, but the regular WD-40 will also lubricate the knobs. Also I thin WD stand for water displacement, so it should be fairly safe for electronics. I found out after this the WD makes and electronics specific product
@scottstolper4473
7 ай бұрын
@@JDArcher So after nine months, knobs working better, worse, or unchanged?
@JDArcher
7 ай бұрын
@scottstolper4473 working way better, except for the volume button, but I think it needed more cleaning and I just have not taken it off since this.
when u gonna paint the fenders?
@JDArcher
Жыл бұрын
Actually, I want to swap them out for the EPI versions. Just got to get the wife to sign off on that...it's been a while
@huyho4071
Жыл бұрын
@@JDArcher gotcha, those will look nice
@JDArcher
Жыл бұрын
@@huyho4071 I like that the vents on the EPI version are flush
what happened to the video about this that you posted yesterday
@JDArcher
Жыл бұрын
I noticed some sound issues, so I went back and fixed it so it would be better
@charlie_r3583
Жыл бұрын
@@JDArcher ohh, have a nice rest of your day
@JDArcher
Жыл бұрын
@@charlie_r3583 thanks
@BeastlyGarage
Жыл бұрын
Good vid. Might want to used electrical contact cleaner instead of WD40 as it won’t leave any oily residue.
@JDArcher
Жыл бұрын
@@BeastlyGarage probably, but the WD also will lubricate the rotational knobs
omg this has happened to me and my r35
@danielroper18
Жыл бұрын
update, i just fixed this in 28 minutes. and it worked like a charm. I owe you a beer next time im in LA
@JDArcher
Жыл бұрын
@@danielroper18 I'll take you up on that