Bravo, finally someone thought about balancing after such a repair. I've seen many clutches repaired in this way, but never with balancing.

@krazed0451

Жыл бұрын

It was only hinted at it the video though... And I can't see anything in the holes Paul tapped opposing the repair once assembled :-/

@t.s.racing

Жыл бұрын

He used set screws, some Engineers call them grub screws, watch the video again.

@krazed0451

Жыл бұрын

@@t.s.racing I'll watch on my computer, I paused several times on my phone and while they were shown briefly resting on the basket I could not spot them during assembly.

@holmes1956O

Жыл бұрын

@@t.s.racing you watch the vid agin I didnt see any in the holes in the hub when he was assembling it

Zrobiłem to samo w honda crf 250 tylko że użyłem śrub nierdzewnych motor jeździ już 4 lata i dalej działa. Polecam pomysł świetny jak i wykonanie :) Szacunek dla twórcy kanału.

Your machine work is unreal!! Really enjoy watching and seeing your creations for fixing and improving parts! Thanks for these great videos!

Muy buen vídeo y trabajo como siempre 👏👏👏

This made my day. Nice work.

Amazing repair

The final balancing gives this job the PRO stamp

*Andaikan saya satu negara dg kamu, saya akan meminta tolong dibuatkan mesin matic 2 cylinder 150cc (75 + 75) dan memapas piringan rumah roller depan bagian CVT-nya, agar saya dapat gunakan sehari-hari & touring. Cara kerjamu teliti, presisi & multi talenta👌*

Muito criativo seu trabalho super top dez de mais

Superb as always

Cool, thank you for teaching your audience that you have to clean your parts before Loctite! Double Points 👍

@jonnoMoto

Жыл бұрын

Not necessarily. There's oil resistant loctite and is fairly common. You have to clean parts for the non oil resistant loctite

@nickj2508

Жыл бұрын

@@jonnoMoto 👻 bad advice. Subjective as to what "oily" means.

@t.s.racing

Жыл бұрын

Correct Nick, lacquer thinner or brake clean and filtered air. Dawn dish soap and water before the air if it's truly critical.

@vishwasachintha9567

Жыл бұрын

@@jonnoMoto kzread.info/dash/bejne/fJx8t6l9drHJj9o.html

@vishwasachintha9567

Жыл бұрын

@@t.s.racing hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh hhhhhhhh

Excellent as always!👍👍👍👍

good repair

Muy bueno, dudo que dure mucho.

I,m a real fan of your videos, and I always give positive feedback. But for this I say order a new inner clutch hub .

👍👍 awesome

Would it have not been better to put countersink in them all to balance it, 👍

Brilliant.

Bro, do you refurbish/reconditio piston skirts? Like adding material and grinding to spec?

Excelente

Yo le hubiese puesto en todos los soportes los tornillos, por el balanceo del embrague lo digo, esos embragues están balanceados.

Was only just thinking about the balance of clutch.when u produced the screws to balance the hub

Why don’t you use green loctite for securing? By the way you are amazing 👌🏻

@t.s.racing

Жыл бұрын

Sir, green is used for pre-assembled fastners. The red is correct. Green has the ability to wick through threads, but not the holding security of red. Yes, I'm a Engineer. I hope this helps.

Esa campana al llevar esos dos tornillos va desequilibrada. Se van a notar vibraciones seguro.

Maravilha 👍👍

Хорошее решение.Надо было и с остальными бонками проделать то же самое.Раз эти две оторвало,то и с остальными может такое случиться.А что явилось причиной поломки?

@cedley1969

Жыл бұрын

It would also be better balanced.

@kotborka

Жыл бұрын

@@cedley1969 да,но вес этих винтов совсем незначительный.

Excelent and simple repair. Paul why my clutch in my ktm exc200 2006, dont dissengage correctly when the engine is hot, the hydraulic is correct, all pieces is correct and normal, the clutch open good and all the disc are free. The friction plates have so much hours but the clutch dont slippe. Is the oil? Regards from patagónia Argentina.

@PaulXchannel

Жыл бұрын

Apparently formed teeth in the basket from use.

Il faut tous les faire pour ne pas déséquilibrer la piece

I did sam few years back on yamaha clutch basket

Could it have a balance problem ?

@krazed0451

Жыл бұрын

Paul seems to hint at counter balancing the repair in the video, but it's only a hint.

I really thought you were gonna weld that back to spec but I guess mechanical force might do it 😂 hope it works out if it goes undone carnage 😅

@holmes1956O

Жыл бұрын

I know we are never gonna see it. But I would like to see how many hour this lasts. My guess is not long

@michi_danksta

10 ай бұрын

​@holmes1956O why would it be an issue. Its very minimal spring pressures. These bosses only break from human error. It'll last until an idiot breaks it by reefing on it with a long handle ratchet

@PaulXchannel

10 ай бұрын

🧠👍

красиво. .

presne takto by sa s tym zabaval moj otec :) ja by som kupoval novy kos/unasac isto :D

🔥👍

Might qswell do that to all 6, so its balanced, one and also so its stronger

I was hoping for your usual magic, that is the way I would have done it. 😉

Хорошее решение. Хорошая работа. Наверно больше как временное решение. Лучше таки заменить эту деталь на новую. Хотя тут явно конструктивная недоработка. 👍🤝🇷🇺

Repair x load= resource.

So, what were they doing during "disassembly" to cause the bosses to break off the hub? I'm genuinely curious.

@kittenfat2207

Жыл бұрын

It said in the video that they used a screwdriver to stop the Boss from rotating while undoing the main nut

@gearb0x

Жыл бұрын

@@kittenfat2207 made the same mistake my self the first time, after replacing the hub i alllllways use a proper clutch tool 😆

@krazed0451

Жыл бұрын

Rattle gun does the job without much holding the inner basket ;-)

How do I get in contact for a cylinder head repair?

Stary, będziesz miał wibracje, lepiej od razu wkręć śruby we wszystkich otworach

Frazione con perni pieni alla fine filettati con dadi ciaoooo

In my country It is called the repair for homeless person. Why do you not put four more screws in the other holes? Is the balance not count in this place?

I am use already a technique

Сомнительное решение

doubt it last

and so unobtainable as to justify such a job?

🤍🤍🤍🤍🤍🤍🤍🤍🤍🤍👌👌👌👌👌👍👍👍👍

i am sorry but this time i must disagree. broken ones cannot be simpli bolted back they are unsure. not even a drop of weld. pardon me , but owner should buy a new one. i respect all your videos and skills but this to me looks like something easyl back broken. too much dangerous for something centrifugated so much.

Completely trash work because that clutch has unbalanced. Just a work for show

@PaulXchannel

Жыл бұрын

watch the video to the end

clutch is not ballanced,,, good idea for repair but its not professional.... inner hub costs less than 100$... good job but not succesful

@krazed0451

Жыл бұрын

Paul hints at rebalancing in the video ;-)

Hmm someone did not buy the clutch holder tool.?????