How to Remove your T56 Transmission in 5 EASY Steps
Don't let the thought of pulling a transmission overwhelm you. It is surprisingly easy!
Next up, pulling the clutch!
0:00 Intro
2:42 Pulling the Shifter
5:47 Pulling the Driveshaft
7:31 Torque Arm and Crossmember Removal
11:26 Transmission Bolts
12:57 Throwout Bearing
14:02 Bellhousing Bolts
Пікірлер: 33
Thanks for making this. Working up the courage and motivation to do this job while cool weather is still here.
Great video my friend. Learned some good stuff
Thanks so much for this video. Truly appreciated! My 2002 has 136k and can’t believe it has the original clutch😮 2 owner vehicle.
Excellent video...... thanks for posting
Great video. Not sure if anyone clarified why the steel alignment dowels between the aluminum bellhousing and the aluminum block gave you such a hard time but steel and aluminum don't mix well. The steel and aluminium corrode when in contact with each other so you always need to use anti-seize compound any time you put these two metals together. Just like using steel bolts to hold the exhaust manifolds into aluminum heads.
@IgniteLight
Жыл бұрын
Appreciate that! It was a struggle.
@b42charlie
Жыл бұрын
you know i always thought it was bad / weird all the bolts were steel on my heads and the waterpump but didnt know why so i never questioned it. good to know
Great content, keep em comin guys!
@IgniteLight
2 жыл бұрын
Thanks! A few install videos coming up getting ready for the warmer months.
Thanks
nice!
I’m going to be dropping mine in my LS Fd rx7 soon
Not sure if you (or anyone else reading this) would know, but I’m curious how similar of a job this would be on an 04 GTO??? Great video by the way! Got a 👍 from me!
@IgniteLight
2 жыл бұрын
I dont think a GTO has a torque are like the Fbodies. So that part would not be applicable. If you have an ls1 GTO and t56 it should be the exact same otherwise. Ls1tech.com is a great site that also has a GTO section that I'm sure has a step by step guide as well.
You should check out a fender flange sheild kit for these cars
@IgniteLight
6 ай бұрын
How am I just now learning about this!?! Thanks!!!
This is gonna help me so much gonna start removing my trans today or tomorrow I just don’t have a transmission jack stand gonna Lemar to use my jack hahah
You removed a 10 mm bolt from slave cylinder area “throw out bearing” What is that for Just curious
@IgniteLight
8 ай бұрын
Just retains the throwout bearing. Keeps it from spinning on the shaft and wrapping the hydraulic lines.
Very nice car and video, mine is grinding when i put it in gear. Mostly when i try to shift quickly, any idea why? Thanks in advance
@IgniteLight
8 ай бұрын
Check out the "drill mod". Sounds like your pedal isn't moving enough volume for your clutch... resulting in a grind. Somewhat common issue for fbodys.
@efrainromo3607
8 ай бұрын
@@IgniteLight Thanks!
Hey great video. I’ve got an aftermarket clutch/flywheel combo in my t56 car with a QuickTime bell housing. It’s a serious pain to get into gear, but when I clutch in the rear wheels don’t spin at all when off the ground. Do you think this would still apply?
@IgniteLight
Жыл бұрын
Seems like the master cylinder for the clutch needs a shim. Tick performance has good videos you'll want to watch that walks you through it.
@hairymoobs
Жыл бұрын
@@IgniteLight Hey thanks for the response. I assume you meant slave cylinder so I went ahead and emailed diamond clutch to see what their specs are. Thanks again.
So since you removed throwout bearing you didnt havr to drain clutch fluid right?
@IgniteLight
6 ай бұрын
I installed a new throwout AND off camera a new master with a speed bleeder. I definitely had to bleed the system quite a bit. If you put a new throwout on, you would need to do the same.
Would you know how different the job would be working on a 06 GTO? Also just an average car guy
@IgniteLight
Жыл бұрын
I can only think of no torque arm for you to remove. Otherwise it should be very similar.
I always throw a couple tires under the car. Rather land on that than flatten me.
Another video that doesn’t show the gear box coming out and down grrrrr
@IgniteLight
Жыл бұрын
A dowel pin was seized the bellhousing and gave me fits. Maybe play the install backwards?!🤣
@cancan8467
Жыл бұрын
@@IgniteLight haha then that would be 10 steps 🤠