One of the best tutorials I've ever seen. Followed it to the letter and my dash is out. Thank you!

@ArcticVette

7 ай бұрын

Thank you for the feedback! You're welcome! 🙌🏼

thanks for your time and efforts great job buddy

@ArcticVette

Жыл бұрын

You're welcome and thank you for the feedback!

Thank you for your awesome video.

@ArcticVette

Ай бұрын

@@warbuzzard7167 you're welcome!

This will come in handy here soon. Heater core change

@ArcticVette

9 ай бұрын

Hope the replacement goes well!

you made this look so easy! idk why ive been putting off replacing my hud trim piece

@ArcticVette

5 ай бұрын

Thanks! It wasn't too bad at all. Someday I'm hoping to put a HUD in mine.

Thank you for your time.

@ArcticVette

10 ай бұрын

You're welcome!

Thank you sir

@ArcticVette

Жыл бұрын

You're welcome! Glad you found it helpful 🙌🏼

Very informative video. Subbed and liked.

@ArcticVette

8 ай бұрын

Thank you for your support! 🙌🏼

Ugh. I may have to take mine out again. Couldn't remember how till I watched your video. I replaced my radio cage since I hacked mine up. Went to install my bezel and the darn cage is crooked.

@ArcticVette

4 күн бұрын

@@retrobear9367 oh shoot, glad the video helped you out!

Man this is all looks so familiar 😅 had to tear mine apart to replace the hazard light switch and that outlet under the radio was also unplugged in mine if I remember correctly

@ArcticVette

Жыл бұрын

Right! I've taken those parts out too many times, I could probably do it in my sleep now 😅

Did you ever do the HUD install video?

@ArcticVette

7 ай бұрын

No, I haven't gotten another deal on a HUD yet. The one I had fell though. It's really not to bad of a process. Check the Corvette forums for a good write up about it.

How do you keep track of screws

@ArcticVette

Ай бұрын

Photo memory, if I take it apart and separate em by size I typically remember where they go. Something I've done in the past is to stab them into cardboard and write the location next to the bolt/screw. That works really well. Hope one of these helps!

Man jobs like that actually scare me lol im too big for tight spaces and just trying to remember where it all goes back... ill stick with the engine bay and exteriors lol

@ArcticVette

Жыл бұрын

😅 I'm glad to have the video to refer to when I put it back together. It's gonna be a hot minute while I wait on parts

How did you re install the glove box? I can’t manage to get the 2 bolts in the holes to screw them to the back plate. Is there a trick? Do I have to get the plastic frame in front. I’m scared to break the hinges. When I put the bolts through the holes the extension is crooked I can’t get them aligned to tighten them.. Any suggestions! Thanks

@ArcticVette

Ай бұрын

I used my fingers to get the bolt started, fitting my fingers through the sides of the glove box. Looking through the 2 holes to see the bolt. Then using an extension and a swivel (joint) socket extension I was able to get the socket on there and tighten them down. A local parts store might have a joint socket.

@believe2806

Ай бұрын

@@ArcticVette Thank you for the feed back! I really appreciate it. I ordered a used glove box today from EBay $175… I will definitely use the swivel socket! Thanks!

@ArcticVette

Ай бұрын

@@believe2806 you're welcome! I hope it goes well for you 🙌🏼