Well done video, just the good stuff. Recently got a 1990 Burb and need to replace these. Great to find out I can swap them with hand tools and no welds. Thanks!

@Offroadfarm1

Жыл бұрын

Thanks for watching!

The inner fenders could take between 20min to 2 days to get out lol. On my truck every single thread clip broke and I had to take a cut off wheel and grind the head off of everyone of those 1/2 in bolts. It was miserable but now that I went through all the work the 1st time now I can take those fenders in and out in like 10 min but man that 1st time was a real struggle.

@Offroadfarm1

3 жыл бұрын

That sounds like a pain! Thanks for watching

@davidfrost4944

11 ай бұрын

Yep. PB Blaster and a side grinder can be your best friends...

Hello Heres an oldy hit.... ITS HIP TO BE SQUARE!!!! very informative!!!

@Offroadfarm1

3 жыл бұрын

Thanks for watching!

I'm about to do some work on my truck. This was very helpful thanks for the video.

@Offroadfarm1

2 жыл бұрын

Glad it helped. Thanks for watching!

Interesting. I always remove the inner and outer fender as one unit. I only separate them off the vehicle and only if I plan on replacing one of them with a new part. I thought for sure that was the advice you were gonna provide with this vid. I was wrong.

Thanks. I've seen a video on hood removal from an '88-'98 Chevy pickup showing one guy (with long arms) doing it. But the older squarebody style trucks have wider hoods which are probably heavier. I could see big back and neck pains if I tried to do that one solo.

@williamb454

Жыл бұрын

MAN UP!!

Offroadfarm.. thank you very much for Showing your 'Channell I looked and did learn a lot about this Job you did; maked me easier to decide purchasing a M1009; near same condition. (dekades back - had had some M-series vehicles M160-M38A1-M37,) did repair alone (had had the *genius TM's - if problems , I'm used the fotos in the manuals..) Only one problem vehicle I had = a Halftrack- M3; here was needed a handhelper. I'm amateur + stealing w/eyes. Do it as an *Enthusiast US-Mil.-vehicles - most sophisticated in world, compensating such Projects to my other business. Gentleman, hope see you again in other videos, wishing You Health and Luck, God Bless Amerika, Greetings from Germany....

@Offroadfarm1

3 жыл бұрын

Thanks for the kind words. Good luck on your projects and thanks for watching

Boltster sir... No ziplock bags needed.

Hey brother I'm 18 kinda of new to building and swapping engines. Iv done just about everything just about except breaking down the block or removing it. Most of all my projects are old school chevys and s10 series trucks. Think you could dumb it down for me on swapping or rebuilding ?

@Offroadfarm1

4 жыл бұрын

I am not an engine expert! I still don't have a motor yet but I will more than likely do a LS swap. When I get that far I will post some videos covering that. If your thinking about doing a LS swap check out "the driveway engineer" channel. He has a lot of LS swap videos and how to do them yourself. Good luck and thanks for watching

Thanks for the video!

@Offroadfarm1

4 жыл бұрын

Glad you liked it and thanks for watching!

I like it still has Goodyear wranglers

@Offroadfarm1

2 жыл бұрын

The driver side front looks like a nearly new wrangler! No idea how old is though. Thanks for watching

Awesome Video! I literally looked for your title & nothing popped up for a while. KZread wasn't being user friendly I guess. Thanks for the post. Just curious if you ever seen the top bolt holding fender on cab by door break through the cab? I have both nuts inside cab break through.

@Offroadfarm1

Жыл бұрын

No I have never seen that . Thanks for watching!

Man my c10 full of spiders 🕷 I’m have to do this power wash it

I want to know how to get the trim piece off the front of the fender! Mines just like the one your working on. Mine doesn’t have speed nuts o. The back side like some I’ve worked on. It has to white plastic rectangular block where speed nuts have been in the past!

@Offroadfarm1

2 жыл бұрын

Which trim piece?

Seems like the inner would come out better if you did the outer first.

@Offroadfarm1

4 жыл бұрын

Yes, if the outer is out of the way the inner comes out easier. Thanks for watching

Must the inner fender be removed to replace the putter fenders?

@Offroadfarm1

3 жыл бұрын

No you can leave the inner fender. Just remember to remove all the bolts from the outer fender to the inner fender. Thanks for watching

Do u have to take doors off. To remove fender cause of spot welds

@Offroadfarm1

Жыл бұрын

No, you should not have to remove the doors. You should be able to just open the doors. Thanks for watching!

Why did u skip showing where the lower bolt is by the door??

Can you put a badge on your truck by just removing the lower part? Trying to put my gmc jimmy emblem on!

@Offroadfarm1

3 жыл бұрын

You can try it but I don't think you will be able to reach the rear nut. If your old emblem is already off and your just installing a new one you could try using barrel clips or 3m double sided automotive trim tape. Thanks for watching!

Is the same for a chevy s10 1988

@Offroadfarm1

3 жыл бұрын

Thanks for watching

My C20 has what I can best describe as a fender brace on both sides (not sure if it's single piece). It mounts underneath the radiator/fan sitting on top of the chassis and connects into the front bottom corner of the outer fenders. No idea how to remove it / what exactly the part is called. You already had it removed in your video -- do you know what its called and how to remove it?

@Offroadfarm1

3 жыл бұрын

Is it one brace for each side? Or one piece that goes completely across the front? Could you snap some pics and email them to me? What year is your C20? offroadfarmchris@gmail.com I'll take a look. Thanks for watching

Can you do one on rockers and cab corners?

@Offroadfarm1

2 жыл бұрын

I am not very good when it comes to autobody stuff, I'm still learning. Check out this video kzread.info/dash/bejne/oIWoramFfdKslKQ.html

@whatsnext8696

2 жыл бұрын

@@Offroadfarm1 ok cool, thanks for the link. Love your content keep em coming. Doing a 74 c10 custom at the moment my self.

Can a new inner fender be put in without the hood and outer fender being removed?

@Offroadfarm1

2 жыл бұрын

Sure can. Thanks for watching

on the inner fender by the cab is there a triangle looking bracket with three bolts

@Offroadfarm1

5 жыл бұрын

Yes there is. you can see that bracket at 1:03. It comes off with the inner fender

@seemslegit191

5 жыл бұрын

@@Offroadfarm1 it doesnt come off of the inner fender do you think if i bought a new inner fender it would come with it

@Offroadfarm1

5 жыл бұрын

Mine didn't come off either. It seems to be part of the inner fender. I have no idea if if it would be on a new inner fender. Keep in mind if you buy a "new" inner fender it is more than likely going to be a reproduction of the original part and will probably not be a OEM part. Reproductions are normally very close to the original but can have some minor differences. My guess is even if it didn't have that bracket it would still have those bolt holes so you could bolt it in. Hope this helps and thanks for watching

Is there any way to remove the two fenders. And the radiator support. All together. As one?

@Offroadfarm1

4 жыл бұрын

Yes, just leave the bolts through the radiator support into the fender. Remove the fender bolts that mount to the cab, and the radiator support body mount bolts. I think you will have to remove your inner fenders unless you don't have a motor installed. Make sure you have someone or something to help you lift all that at once.good luck on your project, and thanks for watching!

@dntreportmebrah134

4 жыл бұрын

Yeah you tube or google "c10 front clip removal."

I wish you had shown the hood removal first. You must have had help with that one.

@Offroadfarm1

2 жыл бұрын

Sorry, I didn't think about showing the hood removal. It is best to have some help to remove it. Thanks for watching

Do you have to remove inner fender

@Offroadfarm1

4 жыл бұрын

No, you can just pull your outer fender if that's all you want to remove. Thanks for watching