How To Program A 2018 - 2023 GMC Terrain Remote Key Fob - Add A Key / Lost All Keys Programming
Автокөліктер мен көлік құралдары
A step by step video on how to program a smart key remote fob to a 2018 - 2023 GMC Terrain.
If you already have two working remote key fobs for your Terrain, you can use the instructions found here www.programyourremote.com/cla...
More free DIY programming instructions available at www.ProgramYourRemote.com
1. Remove the key lock cylinder cap. Insert the GMC Terrain emergency key into the key lock cylinder on the driver door handle; then turn the key counterclockwise, to the unlock position five times within 10 seconds. The Driver Information Center(DIC) displays REMOTE LEARN PENDING, PLEASE WAIT.
2. Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN, then press the ENGINE START/STOP button. (You may have to open and close drivers door to see the DIC display). The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
3. Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. The DIC displays PRESS ENGINE START BUTTON TO LEARN, then press the ENGINE START/STOP button. (You may have to open and close drivers door to see the DIC display). Remaining remote key fobs can be relearned during the next steps. The DIC display should now show READY FOR REMOTE # 1.
4. Place the new smart key fob in the GMC Terrain's cupholder .
5. Press the ENGINE START/STOP button. When the key fob is learned, the DIC display will show that it is ready to program the next remote key fob.
6. Remove the remote key fob from the transmitter pocket and press unlock or lock on the remote key fob.
To program additional transmitters, repeat Steps 4-6. When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for approximately 12 seconds to exit programming mode.
This remote key fob programming procedure applies to following GMC models:
2018 GMC Terrain ( SL, SLE, SLT and Denali )
2019 GMC Terrain ( SL, SLE, SLT and Denali )
2020 GMC Terrain ( SL, SLE, SLT and Denali )
2021 GMC Terrain ( SL, SLE, SLT and Denali )
2022 GMC Terrain ( SL, SLE, SLT and Denali )
2023 GMC Terrain ( SL, SLE, SLT and Denali )
Find a Locksmith in your area with www.LocateALocksmith.com
Пікірлер: 296
I watched 6 videos and yours was the only one that explains how to do it with one working key. Thanks so much for being so detailed.
@PYR-Auto
Жыл бұрын
You're welcome! Glad it helped
I only had one key for my Terrain, I bought a key from Amazon and I used this process to program the new key. It worked out great!!
@PYR-Auto
Жыл бұрын
Nice! Glad it helped
@serenityeziashi
Жыл бұрын
I bought a key on Amazon as well. Where did you get your key cut, and what was the cost?
@azjaheverett
9 ай бұрын
Hey, you mind sharing the link for the fob?
Thank you for this! Saved me $60 for what a locksmith wanted and after the dealership said you can’t do a 2022 GMC TERRAIN. It worked! Thank you sir
@PYR-Auto
5 ай бұрын
You're Welcome! Glad it helped
Finally, I got the keys programmed. Some odd reason on last step mine didn't work like stated. Took me 2 hrs instead of 30 min but a win is a win😂 Thks!
Dude, you rock. This procedure worked first time on my 2018 Acadia. By the way, while it’s probably advisable to get the 2nd key cut, you don’t have to. I have one FOB (original) with key cut, and new FOB with blank, and both FOBs work now after this procedure. However, I do plan on getting the 2nd key cut, because you never know, if you lose that one FOB, you will be SOL on the next re-program and end up paying big $$$ at dealer. Thanks!
@PYR-Auto
2 жыл бұрын
You're Welcome!
@Daniel-ww3hl
Жыл бұрын
So you have two keys 🤦🏻♂️
Brought a key from Amazon because my original key unlock button was broken on key fob. I followed the steps and put my original cut key in the fob. Works great! Thanks saved me a lot of money from the GMC dealership. Worked perfectly for my 2018 GMC Terrain💯
@PYR-Auto
7 ай бұрын
Glad it helped!
@mooselexus
2 ай бұрын
Which one did you purchase on Amazon:)? Could you provide a link, please! Many Thanks!
This video was great! We had the original fob and bought 2 from Amazon. Everything works including the remote start on all 3 fobs. We only had to follow the process one time for each fob. Thanks a bunch!!
@PYR-Auto
5 ай бұрын
You're Welcome! Glad it helped
Thank you. Worked perfectly for my 2018 Equinox. For some reason the hardest part for me was getting the key lock cylinder cap back seated properly. Lol
@PYR-Auto
2 жыл бұрын
You're welcome!
Thank you making this visual aid in programming the remote. I read the procedure in my owners manual but seeing it done helps in making sense of the cut key part.
@PYR-Auto
3 жыл бұрын
You're Welcome! Glad it helped
It worked perfectly on my 2017 GMC Acadia👍🏻. Thanks for the video! 🙏🏻
@PYR-Auto
10 ай бұрын
You're Welcome! Glad it helped
Thank you for posting this video. I was able to program a new keyfob following this procedure.
@PYR-Auto
2 ай бұрын
You're Welcome! Glad it helped
Great video, thanks for posting.
@PYR-Auto
Жыл бұрын
You're Welcome!
Thanks my good man worked perfectly.
@PYR-Auto
Жыл бұрын
You're Welcome!
It worked! Thank you! I think the dealership wanted $300 to do it!! Yay!!
@PYR-Auto
4 ай бұрын
You're Welcome!
Thank you so much! It worked perfectly on my 2019 Buick Enclave Avenir
@PYR-Auto
5 ай бұрын
You're welcome! Glad it helped
Thank you so much! Excellent video.
@PYR-Auto
6 ай бұрын
You're Welcome!
Worked great! Thanks!
@PYR-Auto
3 жыл бұрын
You're welcome!
Thank You from Russia!!!)) Большое спасибо!)) Всем эквиноксам из СНГ привет!!!
BEST HOW TO VIDEO SO FAR. THANK YOU FOR SPEAKING CLEARLY AND SLOWLY.
@PYR-Auto
3 ай бұрын
Thanks! Glad it helped
Success on my 2020 Terrain!
@PYR-Auto
11 ай бұрын
Nice!
Great job ...I needed this help...thanks a lot...
@PYR-Auto
3 жыл бұрын
You're Welcome! Glad it helped
SUCCESS!!! Thank you for sharing
@PYR-Auto
Жыл бұрын
You're Welcome! Glad it helped
Big big thank you brother!
@PYR-Auto
4 ай бұрын
You're Welcome!
Спасибо за видео. Очень помогло. С экономил 200$
Thank you for this! I was hoping to get a 3rd key for emergencies and this will make it easy!
@PYR-Auto
3 жыл бұрын
You're Welcome!
Thank you sir !!
@PYR-Auto
2 жыл бұрын
You're Welcome!
Thank you 🙏
@PYR-Auto
2 жыл бұрын
You're Welcome!
Thank you very much
@PYR-Auto
Жыл бұрын
You're Welcome!
Thank you! Very clear instructions. Do you know if this procedure works for 2019 GMC Sierra 1500?
@PYR-Auto
3 жыл бұрын
Yes - if your Sierra has push button start. The only difference is instead of placing the fobs in the cupholder, you need to place them in the transmitter pocket in your center console
nice
@PYR-Auto
3 жыл бұрын
Thanks
Hello Thank u for all this I was thinking of taking my 2018 Terrain sle to get a key program I only have 1 original and want to program 2 more. So is this mean that I would have reset even the original and add all 3 again?
@PYR-Auto
2 жыл бұрын
Yes exactly
So I’ve lost the original fob, I bought a new emergency key, it’s been cut and programmed by the local Chevrolet dealer, can I now buy a aftermarket fob from Amazon and do this process, do I need to buy 2? Or do I need a locksmith who programs these to be able to start my 2019 GMC Terrain?
Thank you for that do you by chance know the messages in the info screen and what the service messages mean??
@PYR-Auto
3 жыл бұрын
You're Welcome - what messages specifically are you getting?
Hey, great video. Just wondering how can I program my key fob if I have only one of it. The vehicle is in canada and is a used vehicle. Any help will be appreciated
@PYR-Auto
2 жыл бұрын
Unfortunately there is not way to program it in that situation. You will need an automotive locksmith or dealership
So I have a key fob from my old 2019 gmc terrain, but want to reprogram it to my 2021 gmc terrain, everytime I go through the process and get to the part where it says ready for the 2nd one it won't program it..... I'm not sure why?
Hi, thanks for posting will this procedure work for 2020 GMC Terrain ?
@PYR-Auto
Жыл бұрын
Yes - as long as the vehicle was built in the US
Thank you for this but just to clarify, so if I have 1 working key (original), I have to buy 2 extra keys because the original will be erased and it wont work anymore?
@PYR-Auto
3 жыл бұрын
You will only need to buy 1 additional. The original can be re-programmed to count as one of the two total that you need.
Do you recommend an automotive locksmith or the dealership more? I’m mostly concerned with the price
@PYR-Auto
2 жыл бұрын
Automotive locksmiths will usually be cheaper b
Can this be done with compatible used key fobs from the same model but another vehicle? Or can this only be done with brand new key fobs straight from the dealer?
@PYR-Auto
2 жыл бұрын
You can program a used key fob but it needs to have been unlocked or "flashed" by someone with the correct equipment. These fobs lock to a vehicle once programmed and need to be unlocked before they can be programmed again to a different vehicle.
Question, if you are just adding 1 fob and you already have a working fob, do you have to reset your 1st fob??? I would feel more confident in doing this if the 1st fob can keep its programming....
@PYR-Auto
2 жыл бұрын
Yes - you will need to reprogram your original during the procedure as it will be erased.
I was told that some times this did not work and there was a back door way to perform this task. Is this true and is it something that can be done without going to a shop? Thank your for your assistance.
@PYR-Auto
3 жыл бұрын
I'm not aware of any back door programming procedures. This should work every time if done properly with the correct remote - you can also find this procedure listed in your owners manual.
If I have an existing key for my 2018 Terrain SLT that was totaled and just bought a 2020 Terrain Denali can the 2018 key be re programmed to work in the newer vehicle?
@PYR-Auto
Жыл бұрын
No - these keys lock to a vehicle once programmed and need to be unlocked by someone with the correct equipment before they can be programmed to a different vehicle
My 2018 Terrain automatically locks whenever I walk away from the car. When it is in programming mode, will it still do that? Is it OK to sit in car while you are waiting. Should both keys be inside car during programming. Or should you leave one out while programming the other?
@PYR-Auto
2 жыл бұрын
I believe when the vehicle is in programming mode it will override the auto lock feature. Yes, you can sit in the car if you would like. Opening or closing the drivers door doesn't effect programming sos it doesn't matter if you are in or out. You can have both keys with you - I assume by both you mean one is programmed and one is not
Thank you for the information. Looking at some of the FOBs available on Amazon they say they must be programmed by dealer or locksmith. Do you happen to have a link for a second fob that can be self programmed for a 2018 Chevy Malibu? Currently have just one working FOB and would like a spare. Thanks
@PYR-Auto
Жыл бұрын
As long as it is the correct fob for the vehicle any of them can be programmed as shown in the video. The problem with most of the fobs found online is they are aftermarket and not OEM, the aftermarket fobs tend to have more issues in general then the OEM ones. check out bit.ly/CarAndTruckRemotes They have both aftermarket and OEM ( original ) options
@randypeterson7484
Жыл бұрын
@@PYR-Auto thank you for the reply. Yesterday I did check out the link provided, and when I did the live chat I asked if I could program the fob and the response was that a dealer or locksmith needed to do it. But I will look again and make sure I am looking at the OEM ones. Appreciate the information.
@PYR-Auto
Жыл бұрын
Not sure why they are saying that - you can find this procedure in your owners manual on pages 35-37
We have 1 new key fob that needs to be programed and we still have the 2nd key fob that came with the car. Will the 2nd one not work anymore?
Do you know if the cover for the manual door lock is broke and can’t be put back in, does the keyless unlock work or not? I had to pop it open but it was frozen over so the clip broke and I’m just wondering how much of a hurry I should be in to replace it
@PYR-Auto
Жыл бұрын
that cap should have no effect on function - its mainly just for looks. You probably will want to replace it eventually though as Im not sure those key cyclinders are designed to be exposed to the weather all the time
Can confirm this works on a 2023 Terrain
What about passive door lock? Currently have no keys at all. Could I still do it?
Okay sorry for bugging you this much but I bought that Acadia damaged just to give you a better idea and the steering wheel airbag is popped out of it and I'm still putting the front end together I bought the two fobs cut the key put the key in my door cylinder ignition turned it five times counterclockwise and it did not pop up on the dash programming mode could it be that the vehicle still has the airbags popped out which gives it codes and it won't let it program the fobs? or maybe there is another issue
When I turn it counter clockwise 5 times, the dash doesn’t show anything.. am I doing something wrong?
Will this feature work to reset the driver number of the key fobs? I do have 2 working Fobs that came with my 2019 Terrain, but both say you are driver #3... Subsequently neither work with the seating memory features...
@PYR-Auto
Жыл бұрын
Yes - you just need to start with the fobs far enough away from the vehicle so they cannot be detected. The order in which you program the fobs back in will determine the driver #
I Purchased 3 Smart keys (Truck/1396 433m/435451, Exact Same Model Numbers as my current Fobs) to add to my truck that has 2 keys already. I have Tried Everything from the standard procedure like what you have done in this video as well as through the MDI Programmer and Immobilizer relearn with all key relearn and my original keys are the only ones to program. The Seller said 2 keys was new from GMC, the 3rd was their lost keyfob that the 2 was to replace but he ended up trading the vehicle in leaving him with the 2 that was ordered by vin# from GMC that was never Programmed to their truck and later ended up finding their lost remote. So what I'm getting at, Does these remotes need to be reset to allow reprogramming to a new VIN/BCM? Under the MDI tool, Diag says the Transponder was not visible? Batteries have been replaced and tested. maybe dormant remotes? How would I go about reset or activating?
@PYR-Auto
Жыл бұрын
These fobs lock to a vehicle once programmed and need to be unlocked with the correct equipment before they can be programmed again. It sounds like those fobs may still be locked.
How can I program a new fob for a 2018 Terrain from Canada? I only have one original with a cut key.
@PYR-Auto
3 жыл бұрын
Unfortunately the Canadian Terrains require 2 working keys in order to be able to add an additional key yourself. You will need a Automotive Locksmith or Dealership to program the keys for you
Is this procedure exactly the same for a 2020 Chevy Traverse? (except for placing the fob in the cupholder...presumbably would use the indentation under the console mat)
@jerrypark2872
2 жыл бұрын
Nevermind!!! I bought a used 2020 Chevy Traverse and , of course, there was only one key FOB.... I bought an after market FOB off of Ebay and programmed the keys as described in this video (other than a different placement of the key fob--in the console) and it WORKED PERFECTLY!!! Saved me at least a couple of hundred dollars!
@PYR-Auto
2 жыл бұрын
Nice!
2021 Terrain with 5 button the same? Just using the "unlock" to program the additional fob? That will enable all functions on the 5 button like the original? Great video by the way!
@PYR-Auto
Жыл бұрын
Yes, the 5 button will be the same programming procedure. As long as your vehicle originally used a 5 button remote, then the new 5 button remote should function just as the original
What is the frequency of the GM key fobs? I see both 315hz and 433hz advertised for the Terrain.
@PYR-Auto
Жыл бұрын
They can come both ways - it depends on your specific vehicle. If you have any existing remotes you can open it to see the numbers on the inside - The FCC ID is actually the number you want to match
I bought a 2020 GMC Sierra 1500 but it only came with 1 key fob. I found an old key fob we accidentally kept from our previous car, a 2018 GMC Terrain. Can I use the old key fob to the Terrain to program with the sierra 1500?
@PYR-Auto
Жыл бұрын
No, these key fobs lock to a vehicle once programmed and need to be unlocked by someone with the correct equipment before they can be programmed to a different vehicle.
I have both original keys, but something is broken on one of them. Maybe it got smashed? The buttons no longer work… but I assume I can still use the emergency key with the replacement? Great video, btw.
@PYR-Auto
19 күн бұрын
yes - you can use an existing emergency key
Hi I have a 2023 Terrain SLT, I bought another fob and it's the same as the one that came with the SUV HYQ1AS. When it goes to remote 2, it does not program at all. I replace the battery. Can you confirm. I did exactly what you did and it only program my first and not the one I bought.
@PYR-Auto
Ай бұрын
if the vehicle is in programming mode but will not respond to the second remote - there may be an issue with the second remote itself
I done all you said in your viedo but my command start won't work now on any of mt 3 key fobs.
Hi! I just bought a Chevy suburban LT 2015, but It came only with the key 🔑, no fob at all… thing is it has no keyless start button (old school engine start). Any way that I can buy a oem fob and program it? Thanks in advance!!
@PYR-Auto
Жыл бұрын
Unfortunately there is no manual way to program fobs for the non push-button vehicles. You will need an automotive locksmith or dealership.
Is this the same process for a 2022 Yukon? Thank you in advance!
@PYR-Auto
Ай бұрын
No - there is no manual way to program a fob to a 2022 yukon. You will need an automotive locksmith or dealership
Hey just one question. Is it totally necessary cut the new fog or it can work without cutting it? I have the original key and I just wanna add a new one. Thx
@PYR-Auto
4 ай бұрын
You just need at least 1 cut emergency key - you can do it without cutting the new one
Hi would this something I would have to do if say I needed to do a factory reset on my car bc my blutooth won't connect to my car?
@PYR-Auto
Жыл бұрын
no - this should only effect the keys
Missed the window for learning tried to start over not working. Do i leave key in door while i do the programming how long do i have to wait to try again txs
@PYR-Auto
Жыл бұрын
you can take the key out of the door or leave it in - it won't matter either way. You should be able to try again right away
I've got a 2020 sierra and tried this process but the 5 counter clockwise turns don't seem to do anything. Nothing comes on the display. Any ideas? I've got one remote programmed and an additional one needing programming. Thanks
@PYR-Auto
2 жыл бұрын
Some vehicle only show that message for a few seconds right when the door is opened - you might try just going off the time rather than the messages.
@pf123
2 жыл бұрын
Do you have a Cdn market vehicle? I have a Cdn 2021 Sierra. The OM advises "This feature is not available in Canada". Need to have two working remotes to program a third.
@seandevine6768
2 жыл бұрын
@@pf123 the truck was from Canada yes. I bought it from a dealer in Minnesota. So basically I need to have a gm dealer program the fob.
Followed the procedure when it got to the part of start programming key 1 didn't remember the steps looked back on video and must of took to long everything erased turned off on dash now won't even read the key I had working any advice what I can do
@PYR-Auto
3 жыл бұрын
It should not "time out" on you like that but If I would start over from the beginning of the procedure. If you're not seeing the messages on the dash try just going off of the time rather then the dash
This doesn't seem to work for my GMC Terrain 2019, but i'm in Canada. Is there a work around you can help me with ? Please and thank you
@PYR-Auto
3 жыл бұрын
This procedure will not work on Canadian Terrains. The Canadian Terrains require 2 working keys in order to be bale to add a new key yourself. If you have less that two working keys, then you will need to go to a locksmith or dealership. If you do have the two working keys then you can find the programming instructions to add a key here www.programyourremote.com/classified/2019-gmc-terrain-keyless-entry-remote-fob-smart-key-programming-instructions-listing-9675.aspx
By reprogramming the original key fob will it remove the remote start from it?
@PYR-Auto
2 жыл бұрын
No
I’m assuming you leave the cut key in your door handle until your completely done??
@PYR-Auto
3 жыл бұрын
You don't need to but it wont matter leave the emergency key or remove it after you turn it the 5 times
My second key is a used OEM key from another GMC terrain. will i be able to program it as well?
@PYR-Auto
2 жыл бұрын
No - these keys lock to a vehicle once programmed and need to be unlocked by someone with the correct equipment before they can be programmed to a different vehicle
@francodiaco5324
2 жыл бұрын
@@PYR-Auto Can you recommend someone to unlock it or is it not worth the money ..just easier to get a new one i suppose?
@PYR-Auto
Жыл бұрын
All the people that I know that unlock them only do wholesale ( large quantities ) so I honestly don't know how cost effect it is to get them unlocked vs. just buying a new one
How does this work if I do not have push start? 2018 sierra, I have only one key with one fob. I have to use key to start ignition, So I’ll have to program remote and key.
@PYR-Auto
Жыл бұрын
You cannot program the key fobs manually on the non push-button start vehicle. You can program the ignition key yourself in many cases though, those instructions can be found here www.programautokeys.com/classified/2018-gmc-sierra-ignition-transponder-chip-key-programming-instructions-listing-9507.aspx#.ZFp3Ry-B2w4
will this process work on out 2018 impala ? thanks
@PYR-Auto
3 жыл бұрын
If your Impala has a push button start ignition then yes it will basically be the same procedure
What if you car is unlocked, can you just program the blank fob, or do you HAVE to turn the key 5 times?
@PYR-Auto
Жыл бұрын
have to turn key 5 times to get into programming mode
What if I purchased a used key fob? Will this still work since the new one was likely programmed for another vehicle?
@PYR-Auto
11 ай бұрын
a used key fob needs to be "unlocked" by someone with correct equipment before it can be programmed to another vehicle
Thank you for the instructions. I did get stuck on one spot. I started with 1 working remote. I was able to follow all steps and successfully program a 2nd remote. Except, now neither key will start the car. Both remotes now lock, unlock, and remotely start the car, but they don't allow me to start the car using the push button. So the car will not leave park. At the end of following the video, I held the start button for 12 seconds, tested both keys, and they both lock and unlocked the car. Then i tried starting the car, it started once, but The dash then gave me a security error. After I turned my car off, now my car will lock and unlock with the remotes but it won't let me start it. How do I get this fixed?
@PYR-Auto
Жыл бұрын
Are you sure the second remote was successfully programmed? What your describing sounds like what happens when only one remote is programmed - in that situation you will need to hold down the stop/start button for 12 seconds before starting the vehicle every time until the second remote is successfully programmed
How do you program a 2019 GMC Sierra that does not have a push start button, using the ignition key instead?
@PYR-Auto
Жыл бұрын
There is no manual way to program the fobs for the non push button start vehicles. You can program the ignition key though, those instructions are here www.programautokeys.com/classified/2019-gmc-sierra-ignition-fob-smart-chip-key-programming-instructions-listing-9501.aspx#.Y2lz-i-B2w4
Will this work if we have remote start on the key fob, and will the remote start still work?
@PYR-Auto
29 күн бұрын
yes - the remote just needs to match your vehicles options
I have GMC 2021 Acadia but I can’t start the engine with the control can I buy one that can I start the engine with the control ? Help
@PYR-Auto
3 жыл бұрын
The remote start button will only work on the new remote if your vehicle has the remote start option installed. The fobs needs to match your vehicles options.
I'm not in Canada, but I believe my "new to me" GMC Terrain is from Canada. Are there any ways around the "feature not available in Canada" issue? After I turn the key to the left 5 times nothing happens. I cannot seem to get into "remote learning mode" no matter what I try.
@PYR-Auto
9 ай бұрын
The Canadian vehicles require 2 woking keys in order to be able to add additional keys yourself - otherwise you will need a dealership or automotive locksmith
So if i have zero working key fobs, can I program just one? The one i had got ran over and i have the physical emergency key, just no fob.
@PYR-Auto
Ай бұрын
No
@MooseMoto7
Ай бұрын
@@PYR-Auto Thank you for the heads up. Is that why when I tried it doesn't register that it is there to program at all? Or is that another separate issue on its own?
My 2018 Terrain had only 1 fob. I bought an OEM fob and went through the process and only the 1st one reprogrammed. I tried numerous times with no luck. I swapped the batteries between the two and still the result. I bought another replacement fob and still no luck so it must not be a fob problem. The dash instructions read the same as those that show up in your demonstration. Any suggestions?
@PYR-Auto
8 ай бұрын
it sounds like the new fobs themselves may be issue - especially if they are not OEM
@donallen3856
8 ай бұрын
Thanks. Both of the new fobs are OEM.
How do I get my key to open my 2019 GMC Terrain trunk?
@PYR-Auto
2 жыл бұрын
You're Terrain needs to have the remote power lift gate option for that to work
Okay... I failed left and right. Did it twice and failed twice. It said it was ready... but wouldn't see the key fob in the cup rest. It turns out that every year has its own "thang." Some have it in the cup rest. One has it in the back of the center console. Mine, it turns out, has it in the bottom of the console under a rubber matt. I'm on my third try... and am tentatively hopeful. Still an excellent video.
@dfkappy
19 күн бұрын
It worked! Great product. You just have to find the right place to sit the keys to program them.
Si solo tengo una, y sele acaba la pila como lo programo si lo reconoce pa prender pero no para deslaquiar las puertas ni lobprende a distancia como si el control no funcionara
Great Video.... I just bought a used 2018 GMC Terrain SEL and everyone wants at least $200 to replace the missing Key Fob. I have one working and I see replacements on Amazon for $39. Just not positive I trust myself to program the keys. I'm worried I will reset the working key and then have no working keys....
@PYR-Auto
2 жыл бұрын
My concern would be that the new cheap aftermarket fob for $39 won't work at all. I would be more confident using a refurbished used OEM fob than a new aftermarket one.
@johnj28
2 жыл бұрын
@@PYR-Auto My fear of using a USED FOB is that it hadn't been FLASHED and therefore could not be reprogrammed. I am going to try the Amazon NEW After Market first. If it doesn't work, I will have to buy another.
@chelseawood20
2 жыл бұрын
I just ordered one off Amazon and it didn’t work so now my car is stuck in program mode while I wait on the real key fob from gm and it also put my car in theft mode because of the aftermarket one. I would highly suggest NOT to do one from Amazon
Hi! So somehow I have the theft deterrent system service alert on, and my car won’t start unless I hold down the start stop for 12 seconds…. Sometimes when I get in, it says it’s ready for remote 2… any tips on how to fix it?
@PYR-Auto
Жыл бұрын
it sounds like you did not program in at least two keys as is explained in the beginning of the video. Programming a second key should fix that issue
@derrymac2584
Жыл бұрын
@@PYR-Auto so how do I do that now since the theft deterrent mode is on ? Thanks in advance
Is there any possible way you could mess up the working fob?
@PYR-Auto
2 жыл бұрын
the working fob will be erased from the vehicle and then re-programmed but it shouldn't effect the fob itself
Good morning, I followed directions. However, after the process, fob locks/unlocks doors but does not start truck?
@PYR-Auto
Жыл бұрын
Did you hold down the stop/start button for 12 seconds to exit programming mode?
hey man i got a gmc 2019 acadia that i bought and it has no key fobs at all is it posibale to program 2 fey fobs with out going to a lock smith
@PYR-Auto
2 ай бұрын
No - not if you do not have a cut emergency
@user-yc8wo8ci5y
2 ай бұрын
But if I get 2 new fobs and get them cut to the vehicle that can be programmed right
@PYR-Auto
2 ай бұрын
@@user-yc8wo8ci5y yes - as long as they are the correct fobs
I only have one remote original one. The mechanic replaced rhe battery wqs trying to help me iut and the remote deactivated. I went through th steps, got it to activate remote 1 then goes to remote 2. Now there is a "Service Theft Deterrent system" error message. I was able to use thebcar with the error and not it will not allow me to turn on the car and change the gears. Self start and buttons work, but i cannot turn off the car - had to life the hood to get it to turn off. HELP PLEASE!!! What am i doing wrong? Could something be damaged in the remote?
@PYR-Auto
2 жыл бұрын
As is covered in the beginning of the video - you need to program in at least two keys total during the procedure. You will need to get yourself an additional remote to program in with your original.
What if my GMC has remote start, does that transfer over to the new remote?
@PYR-Auto
Жыл бұрын
Yes
If I plan on adding a remote start should I purchase the GMC one made for it Previously to installing it or after the Installation the Viper I want says it works with factory FOB’s
@shawncanning35th
3 жыл бұрын
But I have the basic right now and would need the one with the circle button on it
@PYR-Auto
3 жыл бұрын
You can't just program in a factory remote start fob to non-remote start vehicle - the vehicle needs to be set up for factory remote start as well. If you are adding an aftermarket remote start system - I believe you would need an aftermarket remote with the remote start button for it to work
How to put door handle together?
So, I did this without researching enough about the fob. My 2020 GMC Terrian SLT is stuck in programming mode. I was able to do the process up until it got to remote 2, won't register the new aftermarket fobs off Amazon, reading comments I see I shouldn't have used those. I've bought 2 new original key fobs from the site you provided in another comment (I couldn't find that link anywhere on video, would be a nice addition to avoid people like me who didn't know lol). Anyway, it currently will work if I hold down ENGINE START / STOP for over 12 seconds it'll allow me to use my original fob I got with the vehicle. Says anti theft system needs service. My dealer can't even look at it for 2 months. What I can't figure out is why I can't get it out of that mode. Was looking for some help. Each time I get into the car, it says ready for remote 2. If I dismiss it, the car stays black and won't work. If I hold start / stop for 12 seconds, it'll allow me to use the fob till next time it's turned off. Sorry for the book, TIA for any suggestions!
@PYR-Auto
Жыл бұрын
Programming a second remote should resolve that issue
@dioncooper4354
Жыл бұрын
This is the exact thing that happened to me. Did you resolve the problem?
@manchildsgt77
10 ай бұрын
@@PYR-Autosame for me only when I get in the vehicle is say "Ready for key 1" where would I go from here?
Planning on using these instructions to program a used GMC smart key to my mom's 21 GMC terrain bc I took a knife to my mom's spare key and it doesn't work anymore I'm keeping the one that doesn't work and she'll have a new for her car spare key
@PYR-Auto
2 жыл бұрын
Good Luck!
@aidenroose3246
2 жыл бұрын
@@PYR-Auto thanks
i wasn’t able to program a new remote i got so i just reprogrammed the original key fob back to my gmc and it works but now everytime i remote start it it like goes back into programming mode so i keep having to hold the stop/start button for 12 seconds before it can actually turn on. how can i fix this?
@mxnddaaa
11 ай бұрын
if it makes any difference i do have a 2019 gmc terrain
@PYR-Auto
11 ай бұрын
You will need to program a second remote to fully exit programming mode
I used the procedure and everything works except starting the car remotely (outside the car). What do I do now?
@PYR-Auto
2 жыл бұрын
Does the car have the remote start option, does it work on your original remote?
@erincrawford4157
Жыл бұрын
I have the same issue. Remote start doesn’t work on original or new fob. But programming them was a breeze with your video.
Does this also program auto start for 2020 Terrain
@PYR-Auto
3 жыл бұрын
Yes, if your Terrain has the remote start option. The remote fob needs to match your vehicles options.
@allenburnham9307
3 жыл бұрын
@@PYR-Auto I was told that periodically this would not work and there is a back door way to perform this task. Is that true and is it something can be done without going to a shop?
2029 GMC Terrain I have one working key I purchased second one on Amazon. I had the key cut at a locksmith. When I start the instructions you gave and the turn the original key to the left it starts beeping and going into the alarm and won’t stop. Why is it doing that? It does say remote learn pending but the beeping and alarm won’t stop unless I hit unlock.
@PYR-Auto
Жыл бұрын
Does it do that even if you unlock the vehicle with the working remote before you start the procedure?
@laurentorres3302
Жыл бұрын
@@PYR-Auto Yes
@PYR-Auto
Жыл бұрын
Not sure why its not deactivating when the vehicle is unlocked with the working fob - that's how it is supposed to function