Thank you so much. Your videos have now saved me over 450 dollars. I only ended up spending 60 dollars on the new fobs from Amazon. I used the emergency key from the out of order fob. Thank you again. Life saver ❤

@PYR-Auto

11 ай бұрын

You're Welcome! Glad it helped

You just saved me $600 dollars here in California, this dealer prices are out of control, for that you get my thumbs up brother thank you.

@PYR-Auto

10 ай бұрын

You're Welcome! Glad it helped

This worked for me on an 18 Yukon that had only 1 fob. Programmed a second aftermarket fob. I had to go through the procedure twice. First time the second fob didn't work and the first fob worked but showed a service theft system message. The second time both worked as they should and no error messages. I will say make sure your car is unlocked before you start as you might set off your theft system if unlock with key after locking with fob!

Thanks for the clear and concise instructions. Worked exactly as described. 3 minutes of attention over a 30 minute period.

@PYR-Auto

2 жыл бұрын

Nice! You're Welcome!

I just watched this video and the step by programming worked the very first time I tired both of the key fobs/smart keys. I just have to now get the second key fob (the newer one) that is the key blade cut to match the original key bade in the original key fob. One only needs the blade key for emergency access on the driver door key hole to the vehicle in the event that the battery dies inside the key fob. At which point even without a working battery in the key fob if you insert the same key fob in to the small key fob holder inside of the center console storage area of the vechicle and push the engine start button, the vehicle will start. Thanks for the great content. All the best to you !

@PYR-Auto

2 жыл бұрын

Glad it helped!

I just programmed 2 fobs and it went flawlessly. thank you so so much.......omg how did we live without youtube 30, 40 years ago?

@PYR-Auto

Жыл бұрын

Glad it helped!

@HuntMountain06

9 ай бұрын

Chilton’s.

Thanks it worked and I had lost a remote, so the fact that all pervious remotes were reset was great 👍

@PYR-Auto

2 жыл бұрын

Glad it helped!

I have a 2020 GMC YUKON xl…. And I was able to program my replacement Key fob myself. Saving my $450. Thank you so much

@PYR-Auto

6 ай бұрын

You're Welcome!

Had an issue where one fob would work with the hands free lift gate and one would not. Followed your steps to reprogramming both remotes and now they both work the hands free lift gate option. Thanks for the how to video, saved me trip to the dealership.

@PYR-Auto

2 жыл бұрын

You're Welcome! Glad it helped

THE BEST teacher EVER!! Thank you!

@PYR-Auto

2 жыл бұрын

Thanks! Glad it helped

Perfect. Clear and concise. It worked the first time. Just used a little patience following the exact instructions and this saved me $180 that the dealership wants to charge!

@PYR-Auto

2 жыл бұрын

Awesome! Glad it helped

Worked for me the first try. What a pain in the ass though! Still I appreciate the video and the help. All the best.

Thanks for the info it worked perfectly for me versus paying 150 a piece for each key fob

@PYR-Auto

3 жыл бұрын

You're Welcome!

Thank you so much for your time this video was easy to follow I appreciate your help!! Saves us all time and money. 🙏🏼✨

@PYR-Auto

2 жыл бұрын

You are so welcome!

@DomskiOKKK

2 жыл бұрын

Where did you get your second key Fob from?

Worked great for my 2019 Yukon XL SLT. Thanks!!

@PYR-Auto

2 жыл бұрын

You're welcome!

Worked great! Make sure the fob is all the way in the slot. Had to do it twice because I had a small keyring on it.

@PYR-Auto

Ай бұрын

Good tip!

Thank you, just bought a used 2018 Yukon XL Denali but seller only had one remote. I am glad that the remote that was missing will not work with the SUV now. I programmed 4 new remotes. Saved $$$$

@PYR-Auto

3 ай бұрын

Glad it helped!

Hey man just did it and it worked flawless

@PYR-Auto

2 жыл бұрын

Nice!

My 2019 Yukon XL Denali never got the red screens but it all worked fine. I found these same instructions on page 37 of my manual, too.

Thank you! This worked great for me. 2019 GMC Yukon XL

@PYR-Auto

Ай бұрын

You're Welcome! Glad it helped

This worked like a charm for me, thanks! I didn't think it was working right but after 3 or 4 10 minute waiting periods it finally said to program key #1.

@PYR-Auto

3 жыл бұрын

You're welcome!

@kristishirley9281

Жыл бұрын

It didn't work for me. Can you tell me... Did you have to wait 10 minutes longer than the normal 10 minutes, each time?

Worked for me, Thank you so much. AWESOME VIDEO!!!! 😊

@PYR-Auto

Жыл бұрын

You're Welcome!

Worked perfectly saved me 120 for such a simple process

@PYR-Auto

Жыл бұрын

Glad it helped!

Thank you! Worked like a charm!

@PYR-Auto

2 жыл бұрын

You're Welcome!

Awesome video. Dealers everywhere have less gas money for their YATCHs.

Wow... well done. Worked and saved a bunch of money

@PYR-Auto

2 жыл бұрын

Glad it helped!

It worked great for me! Thank you so much!

@PYR-Auto

Жыл бұрын

You're welcome!

Thank you so much i program 4 key to my truck everything worked just like you said it would

@PYR-Auto

9 ай бұрын

You're Welcome! Glad it helped

Worked great. Thank you!

@PYR-Auto

Жыл бұрын

You're Welcome!

Added an additional GMC key fob transmitter and process in this KZread video work well

@PYR-Auto

3 жыл бұрын

Great!

Thank u. Work like a charm!!!!

@PYR-Auto

Жыл бұрын

You're welcome!

Thank you, amazing video.

@PYR-Auto

Жыл бұрын

You're Welcome!

Just an FYI for others who may run into this problem- our display wasn’t “waking up” to prompt us after the first ten minutes. So we just did it exactly as instructed, pretending that we got the prompt to hit the start button. We did get the “ready for key fob #1” at the appropriate time though. No idea why our display wasn’t prompting us in the second step (the one that needed repeated every ten minutes) - but we got our fob programmed so we are happy! (2017 gmc Denali )

This procedure works ‘ I just programmed 2 remotes on my 2017 Yukon xl

@PYR-Auto

Жыл бұрын

Nice!

Worked perfectly for me

@PYR-Auto

2 жыл бұрын

Great!

Very helpful, thanks

@PYR-Auto

Жыл бұрын

You're welcome!

Truly a life saver!

@PYR-Auto

3 ай бұрын

Glad it helped!

Worked like a Charm

@PYR-Auto

6 ай бұрын

NIce!

I have FOB #2 and #3(uncut). I wanted to reprogram them to 1 and 2 so the seat memory would work. I put #2 in the door and did the 5 counter clockwise turns. The driver display then said "Ready for remote 4" Nothing I did changed anything so I held the start/stop for 12 seconds until the screen went blank. *****UPDATE***** If I would have just scrolled down further I would have solved my own problem. I didn't have the fobs far enough away to put it into learning mode. Once I got that far - the rest was easy. Thanks for the video and the feedback to the other users.

@PYR-Auto

Жыл бұрын

You're welcome! Glad you got it figured out

Thank you 👍👍👍👍👍👍

@PYR-Auto

2 жыл бұрын

You're Welcome!

Hi great video and extremely detail. I’m wondering if this is a step I should be doing on my 2016 GMC Yukon as well if what my issue is my remotes that were working for years quit working and I’ve replaced my batteries in each of them but still won’t remote start or even u lock or lock but it will start the car if I put both in the pocket. Now days I have to take the key out to unlock the door and the alarm goes off until I get the key in the pocket. Any help would be great.

@PYR-Auto

3 жыл бұрын

Thanks - Are you sure you installed the new batteries correctly? its pretty common to install them upside down.

Is there anyway to do this for a 2016 Yukon? I programmed a second key years ago, but it’s key 3. I would like to delete the keys out and reprogram them for just key 1 and key 2.

When programming the remotes does this also erase the memory seats that are already set? We currently have only 1 working factory key (but we have Driver 1 and 2 programmed, I just use the button each time, which is a huge pain) and will be adding a second using the complete relearn procedure in your video. Will it keep the seat/mirror settings or will they need to be reset afterwards?

@PYR-Auto

Жыл бұрын

which key fob the vehicle recognizes as driver 1 or 2 will be erased and then determined by the order in which you program the key fobs back in, but I'm actually not sure if the driver setting are erased from the vehicle itself

@WhoaFiveOh

Жыл бұрын

@@PYR-Auto Ok, cool. I appreciate the response anyway! I can update after I do the programming.

This works for a 2016 Yukon denali too right? I just got a second self programmable fob and I'm not wanting to pay the money at a dealership if I can avoid it. I'm aware I need to go and get the key cut but that's cool. Please tell me this will work 🙏🏼?!

@PYR-Auto

Жыл бұрын

it will work but if you already have 1 working key there is a shorter procedure you can use. That video is here kzread.info/dash/bejne/hpirptmyZanHm5s.html

Where is the key fob slot located on the pickup trucks with the center console? I don't have any slots in my center console for the key fob.

@PYR-Auto

2 жыл бұрын

its the slot that is in between the front cupholders on the Sierra's

Thank you for this valuable information. I bought a aftermarket remote from amazon. I attempted 3 times to get the aftermarket remote to program but no success. My problem now is the vehicle security light now stays on and says it need service. Would you have any ideas on how to remedy this? Thank you!!!! Now the truck will not start with push button after you remote start it?? I guess my new remote could have a bad battery? PROBLEM SOLVED,!!!!! The new remote I bought from amazon had a bad battery. Replaced battery and was able to program new remote and all works fine.

@stanleyscott9266

2 жыл бұрын

Problem solved see above

@PYR-Auto

2 жыл бұрын

Cool - glad you got it figured out!

My 2018 Yukon has 2 programmed keyfobs - one in my possession and the other is not. I have a refurbished fob I’d like to program. Can I still do it with one of the 2 programmed fobs in my possession?

@PYR-Auto

2 жыл бұрын

Yes, you just need to add 2 remotes total - so your new fob and the 1 previous fob will give you the two total needed

How do I change the memory features for the new remote? The dealership has it programmed to memory 3 but it needs to be 1.

@PYR-Auto

2 жыл бұрын

When you do this procedure it erases all previous remotes and the in order in which you program them back in will determine the driver #.

This is GREAT! I just ordered a replacement key fob & the GMC dealership told me that it is a 1 shot deal with the programming, so if I make a mistake I won't be able to try again. Is that true??

@PYR-Auto

Жыл бұрын

the key fobs lock to a vehicle once programmed but can be re-programmed to the exact same vehicle an unlimited number of times

Where is the best place to get an extra key fob? I see a lot of options, but not sure what will really work.

@PYR-Auto

3 жыл бұрын

I would recommend bit.ly/CarAndTruckRemotes

I have a 2018 GMC Yukon XL and I am unable to get it into the fob programming mode. By the VIN it was manufactured in Arlington, TX. Not sure if was originally sold in Canada though. I have one working fob with a cut emergency key.

@PYR-Auto

2 жыл бұрын

If the vehicle was manufactured in TX you should be good but this procedure will not work on Canadian Yukons. Some vehicles only show the messages on the dash for a few seconds right when the door is opened. Have you tried just continuing with the procedure and going off the time?

@JimmyGreen9

2 жыл бұрын

@@PYR-Auto does this process not work on vehicles sold in Canada? Is there a process that will or are we hooped?

For some reason it did not program the 2nd remote. We have a 2019 Yukon xl but we have a 2nd key fob from our prior 2017 suburban that was totaled. Should this still work?

@PYR-Auto

2 жыл бұрын

No - these keys lock to a vehicle once programmed and must be unlocked by someone with the correct equipment before they can be used again.

If one of the key is lost will it still work if found? After I programed a new 1?

@PYR-Auto

2 жыл бұрын

This procedure will erase all previous remotes but they can be re-programmed to the same vehicle again if they are found.

I have a key fob from a 2017 GMC Sierra. Would I be able to program that fob to my 2018 GMC Yukon XL?

@PYR-Auto

3 жыл бұрын

Unfortunately no

Hey there.. I have the key fob but I don’t have the actual emergency key that goes inside.. does it have to be a cut key to work or could it be an uncut key to program a second key? Thanks

@PYR-Auto

3 жыл бұрын

The emergency key will need to be cut in order to do the procedure

@DuggyFresh81

3 жыл бұрын

@@PYR-Auto thank you!

👍 thanks

@PYR-Auto

2 жыл бұрын

You're Welcome!

Thanks for the video. I was wondering what to do if you have 2 working remotes, but none of them show up as driver 1 or driver 2 in the DIC?

@PYR-Auto

Жыл бұрын

You can use this video - this procedure will erase all remotes and the order in which you program them back in will determine driver #

@petegiella

Жыл бұрын

@@PYR-Auto THANKS

@PYR-Auto

Жыл бұрын

You're Welcome!

I lost my remote 2. I bought a replacement fob from the dealer. I have followed the process 3 times. Each time my original remote works a fob 1 but the replacement fob from the dealer will not program as fob 2. I replaced the battery in it thinking it was the problem , but it will not work. Any thoughts?

@PYR-Auto

2 жыл бұрын

There may just be an issue with the fob itself

Do you have a suggestion on the best place to order a key fob

@PYR-Auto

Жыл бұрын

check out bit.ly/CarAndTruckRemotes

I bought new FOB from Amazon with a blank for the emergency key. I tried to program the new FOB and did not work. Do you need to cut the new key for the new fob to work?

@PYR-Auto

2 жыл бұрын

No, the emergency does not need to be cut in order for the fob to program - you just need at least one emergency key for the door

So I did this with my 17 yukon and added a 3rd key. Got rid of the yukon now have a 15 suburban. can i use that 3rd key that i kept to reprogram it to use with the suburban?

@PYR-Auto

2 жыл бұрын

It would have to be unlocked by someone with the correct equipment first. These fobs lock to a vehicle once programmed and need to be unlocked before they can be used again.

My message display does not stay on like the one in this video

Apparently the fob I ordered off eBay won’t program. So now that theft deterrent like and message is stuck on. Any idea how to get it off? I’ve tried unhooking the battery, turning off program mode, etc

@PYR-Auto

3 жыл бұрын

If the vehicle will not let you exit programming mode by hold down the stop/start button you may need to successfully program 2 remotes - as shown in the video - to get the theft deterrent message off

We have tried this three times, we get a message to program key #4. From the dealer we got programmed key 2 & 3. We are trying to reset them so they work with the seats. It does not come up witht the Remote Learn Pending message. Suggestions? Thanks for your help!

@PYR-Auto

2 жыл бұрын

You are in the "add a key" procedure since your vehicle is detecting two already programmed fobs. Start with both of your fobs far enough away from the vehicle so they cannot be read by the vehicle ( not including the emergency key you need to use to get the vehicle into programming mode ). Once the vehicle enters programming mode you can bring the fobs back to the vehicle.

I have a 2019 Yukon denali, I have 1 working remote currently. My brother also had a 2019 yukon denali, when he traded it in he kept one of his fobs. Would it be possible to reprogram this fob to my vehicle?

@PYR-Auto

Жыл бұрын

No - these fobs lock to a vehicle once programmed and need to need to unlocked by someone with the correct equipment before they can be programmed to another vehicle

Are you supposed to have the new fob away from the vehicle at first ?

@PYR-Auto

2 жыл бұрын

no

I have a 2017 GMC Yukon sle I had to get a new bcm all my lights stopped working I got it programmed at dealership then they told me I needed 2 new key fobs and program them for 600 to new bcm I got 2 of Amazon & programmed them thru this video but everything works but car won’t start

Apparently when I buy a used GMC 2018 terrain I must insist that the dealer include two remotes that are programmed to the vehicle before I drive it off the lot, and check that at least one of the remote emergency keys is cut and works in the slot?

@PYR-Auto

3 жыл бұрын

That would be ideal but you only need one working key with the emergency key cut to add another one yourself

Hi, I went through the steps and at the end it will lock and unlock but will not start the 2017 Denali. Any help is appreciated! I ended programming mode and tried to start over (turning key 5 times) but I am not getting any messages on my screen.

@PYR-Auto

2 жыл бұрын

How many remotes total did you program to the vehicle?

@christydalton4335

2 жыл бұрын

@@PYR-Auto I had the original and a new unprogrammed one from dealer. It was my battery… I waited another 20 minutes and tried to start vehicle again and it said battery. Both remotes are working now, I haven’t tried remote start yet. Thank you so much for your video, it worked the first time just didn’t know my battery had went dead and that was the cause of it not starting.

@PYR-Auto

2 жыл бұрын

Cool - Glad you got it figured out!

I have a 2019 Yukon SLT. The current key fob does not have a removable emergency key. It also is started with a key (no push start) Any recommendations for programming a new fob?

@PYR-Auto

5 ай бұрын

unfortunately there is no manual way to program the fobs for the non push button start vehicles - you will need a locksmith or dealership

@geraldvickers6447

5 ай бұрын

@@PYR-Auto thanks for getting back with me.

So you will need two keys to program? I only have one , the original got lost and got a new one from the dealer (only one)

@PYR-Auto

Жыл бұрын

you need two keys total. So if you 1 existing key and 1 new key then you have 2 total

What would be the potential cause of this working up to the first point where you see the message to wait and start the first ten minute timer - then it just goes away on screen like it never happened after about 30 seconds... I have one programmed fob, i tried leaving in the car and taking out, tried many times just keeps disappearing and not doing anything. (2017 yukon denali). Great video by the way and very helpful too.

@lynchburger777

2 жыл бұрын

Adding an update - The display messages will disappear after a few seconds on my 2017 yukon. I kept thinking it was failing, so I sat in the car and waited 10 mins and right at ten minutes it came back up for a moment, pressing the engine start then as directed by you worked. Message went to sleep again and in ten more minutes came back with the ready to program message. Programmed my existing remote (which i bricked due to impatience) and a new aftermarket one from amazon flawlessly after this. MANY THANKS FOR THE VIDEO!!!!!!

@PYR-Auto

2 жыл бұрын

Yeah most vehicles only show the message for a few moments right when the message first comes up or when the door is opened. Anyway, glad you got it figured out!

I’m in the US, but I “think” my truck was manufactured in Canada. I have two fobs programmed as 2 and 3, and want them to be 1 and 2. Will this work on my truck or does where the vehicle was built take me out of the running? Also, if this won’t work because of that, can dealership fix this for me? Thanks so much

@PYR-Auto

Жыл бұрын

Unfortunately this procedure does not work on Canadian built vehicles. Yes, a dealer or automotive locksmith should be able to erase the key fobs and reprogram them which would reset the driver #'s

Hi, well done video but hoping you can help. i bought a 2018 that only had one remote. I bought an additional remote, and I followed these instructions carefully. I have gone through the sequence fully twice now, and after i progrma remote 2, and hit unlock, i hold the start stop for 12 seconds. But it always programs the new remote as remote 3, and not as remote 2, so the auto seat memory feature doest work because that only works with remote one and two. can I not program an afternmarket remote as remote 2?

@jseib2293

2 жыл бұрын

I just went through the entire sequence again, and my spare remote stills driver number three when I get in the truck.

@PYR-Auto

2 жыл бұрын

Try going though the procedure again but start with all the fobs far enough away from the vehicle so they cannot be detected.

@jseib2293

2 жыл бұрын

Thanks. It worked! I did that plus one more thing, I swapped the order of remote programming. So what was remote three is now remote one, and remote one is now two. Likely your trick was the cure but either way they now work and the memory works properly as well. Thanks for the reply!

Will this work if you have a single damaged remote? The remote I have had a corroded battery and the lock unlock buttons no longer work. I’m afraid if I try this myself I will have no working keys!

@PYR-Auto

2 жыл бұрын

No - You need at least two remotes total and they both need to be working

Hey how did you get the red backlighting on your guages and controls?

@PYR-Auto

2 жыл бұрын

I believe thats just the factory setting

@davidmatyis1732

Жыл бұрын

@@PYR-Auto The 2015 & 2016 models had red backlighting.

Is this similar for 21-23 GMC Yukons, it has been a long time since this was published ??

@PYR-Auto

9 ай бұрын

its a little bit different in the 21-23. You can see that video here kzread.info/dash/bejne/ameNo4-sZdfAk9o.html

Do you leave the key in the door the whole time?

@PYR-Auto

2 жыл бұрын

I did not but It won't effect the programming either way

This all worked great with one exception. I have a 2018 GMC Yukon Denali. I had one working key and a new keyfob I bought online. After programming both keys, I found out that indeed my original key was keyfob #1, however the second (brand new key) was not keyfob #2 as I expected, it was programmed as keyfob #3, and therefore I was not able to link the new keyfob to Driver number 2. I was unable to get the new keyfob to be recognized as keyfob #2. When I repeat everthing from scratch using this youtube video, it tells me to insert keyfob #3. Shouldn't it be asking me for the first keyfob (aka #1) and then the next one (aka #2)? not sure what is going on. both keys work, just not seat setting for driver @2.

@PYR-Auto

2 жыл бұрын

Start with with the working key fobs far enough away from the vehicle so they cannot be read then go through the procedure just as it shown in the video.

@camfam

2 жыл бұрын

Did the same thing for me, I can’t get it to learn the 2nd key…

@toubeeyang2979

7 ай бұрын

Having same issue. Original key fob #1 is driver 1 but the new key fob #2 is showing up as driver 3... tried it multiple times. Same result 😥

Could this work for a 2017 GMC Acadia Denali with a push start?

@PYR-Auto

Жыл бұрын

Yes

I just performed your step by step instructions to program an extra key fob. My second did not work and activated the Theft Deterrent System. The vehicle theft deterrent system light came on. How do I get the Theft Deterrent System light off. Hopefully you have the answer.

@PYR-Auto

2 жыл бұрын

at least two remotes (including your original ) need to be successfully programmed during the procedure or the theft deterrent can activate. There may be an issue with the new remote you are trying to use

@ro7096

2 жыл бұрын

@@PYR-Auto Got the second and third remotes today. I followed your steps and everything is working great. Thank you for your instructions and reply!

@PYR-Auto

2 жыл бұрын

You're Welcome!

@tmccall72

2 жыл бұрын

@@ro7096 Did you end up purchasing the two additional remotes for this to work?

@irod.87

2 жыл бұрын

This happened to me. Explains the light. 2nd remote didn't program successfully the first time. Might have been the battery as I put a new battery before the second attempt and it worked as it should.

Hey I had 1 working key and was trying to add a second from a past Tahoe. I know now that doesn’t work. Went through the sequence and now neither will start the car or lock the doors. A second key that the dealership found for our Yukon is being sent to me. Will that key work or is it now deprogrammed also?

@PYR-Auto

2 жыл бұрын

It will be deprogrammed but you should be able to reprogram the original keys to the vehicle - these keys lock to a vehicle once programmed but can be reprogrammed to the exact same vehicle an unlimited number of times

@Codystube1

2 жыл бұрын

Bought a $20 Amazon key in hopes of getting rid of the theft deterrent code while we wait on the dealership. Amazon key seems identical aside from the GMC backplate. Sequence worked perfectly. Theft deterrent message gone, remote starts, locks/unlocks, no error messages! You’re a good man!

i changed the hood latch sensor do i have to reprogram the key fobs?? because i lost the remote start function.

@PYR-Auto

2 жыл бұрын

Replacing the hood latch sensor should not effect the remotes themselves however I'm not sure if the hood being detected by the vehicle as open can prevent the remote start from working (if there is still an issue with the sensor). Also - you may want to check your vehicles settings to make sure the remote start is not disabled anywhere .

@Leto4900

2 жыл бұрын

@@PYR-Auto thank you for replying, we detached the latch because the car couldn't detect its signal, maybe the latch itself not working . thanks again.

Will this work for a 2017 GMC Acadia Denali?

@PYR-Auto

3 жыл бұрын

Yes - it should

What about if you don't have the smark key system?

@PYR-Auto

Жыл бұрын

There is no manual way to program the fobs for the non push button start vehicles but you can program the ignition key in most cases. You can find the ignition key programming instructions here www.programautokeys.com/classified/yukon-browse-794.aspx

I have tried this several times and I am not getting the remote learn message after turning the key. My Yukon is from Canada, bought in the States, would this make a difference?

@PYR-Auto

Жыл бұрын

Yes - that does make a difference. The Canadian built vehicles require two working keys in order to be able to program an additional key yourself.

I just got a 16 yukon and it came with 2 key fobs and they are set to driver 2 and 3. How do I set them to driver 1 and 2 for the memory seats? Tried this but it says add key 4

@PYR-Auto

2 жыл бұрын

Do the procedure shown in the video but make sure you have your keys far enough away from the vehicle so they cannot be read until the vehicle is in programming mode - otherwise the vehicle will "add" remotes instead of erasing all previous and starting from driver 1.

@RobertB1000

2 жыл бұрын

@@PYR-Auto thank you. I had the keys in my pocket when I tried it.

What do I need to do if I need to start the process over? I think I messed something up.

@PYR-Auto

2 жыл бұрын

hold down the stop/start button for 12 seconds to exit programming

I tried the procedure and messed up. Then I could not get the first screen again, and the emergency key feels like it is locked and doesn't bounce back when you turn. Is this some sort of theft deterrent or is the key pad jammed/broken?

@PYR-Auto

2 жыл бұрын

It sounds like the key cylinder may be jammed/broken - the theft deterrent does not operate that way

Can I program a fob that was paired to my wife's previous Yukon?

@PYR-Auto

Жыл бұрын

no - these key fobs lock to a vehicle once programmed and need to be unlocked by someone with the correct equipment before they can be used again.

Will the remote start still work with this method?

@PYR-Auto

3 жыл бұрын

Yes - if your vehicle has the remote start option installed. The remote needs to match your vehicles options.

My GMC 1500 Sierra AT$ does not have the 'pocket' in the center console- any suggestions? Thanks,

@PYR-Auto

Жыл бұрын

What year is your sierra?

@hammerhead1224

Жыл бұрын

@@PYR-Auto 2019 AT4

@PYR-Auto

Жыл бұрын

The slot will be between the cupholders on the vehicle with bucket seats. You can see where that pocket is on in the video below. kzread.info/dash/bejne/qKqXscebf8bMo6Q.html

I can't get my 2018 Yukon XL to enter programming mode. I turn the key 5 times, but nothing happens. When I open the door, the mileage shows at the bottom of the DIC, but nothing else. Vehicle was manufactured in Arlington, TX, but I do know it was previously a leased vehicle in Canada. Any ideas?

@PYR-Auto

2 жыл бұрын

As long as it was manufactured in the US that should not be an issue - this procedure does not work on Canadian vehicles though. I would try just going through the procedure using the time rather then the messages on the dash - some vehicles only show them for a few seconds or seem to not show at all.

@davidmtml

2 жыл бұрын

Thanks. The message definitely never shows up. Also, just going by time, when I press the start/stop/ignition button, the DIC shows up like it normally would saying that no keyfob is present so it can't start. Would that show up if it indeed was in programming mode?

@PYR-Auto

2 жыл бұрын

No - that would indicate the vehicle is not in programming mode. I'm not sure why you're vehicle will not enter the programming mode - this is a factory procedure that can be found in your owners manual so the vehicle is designed to do it.

@davidmtml

2 жыл бұрын

@@PYR-Auto Thanks. You mention before that Canadian vehicles this won't work. Is it that they won't go into programming mode? Or will they go into programming mode but just not accept new keys?

can you do a video on how to program a 2021 gmc terrain key and fob both all keys lost and just adding a remote just incase my mom has to get a replacement

@PYR-Auto

3 жыл бұрын

Here is a link to the programming video for a 2021 GMC Terrain. You can use the procedure to just Add a key if all keys are lost kzread.info/dash/bejne/d5yIxcGadJawpso.html

@aidenroose3246

3 жыл бұрын

@@PYR-Auto thanks

@PYR-Auto

3 жыл бұрын

You're Welcome!

Any insight on programming a non smart 16 Yukon sle remote

@PYR-Auto

3 жыл бұрын

Unfortunealy there is no manual procedure to program the non-push button start fobs.

@b.s.rservicerepair7661

2 жыл бұрын

Need the same thing

How do I do it with a key ignition starter because it's not a push start

@PYR-Auto

2 жыл бұрын

There is no manual way to program the fobs for a regular ignition. You can program the ignition keys though - you can find those instructions here www.programautokeys.com/classified/yukon-browse-794.aspx

Each time I do this, I get key number one correct, key number two becomes key number three, and key number three becomes key number 3.... Any suggestions?

Hello, I did program by autopropad Program done but security light standby when engine start and so on Please help Thank you

@PYR-Auto

2 жыл бұрын

I'm not familiar with autopropad, sorry

@mohammedkareem9972

2 жыл бұрын

@@PYR-Auto I am glad that you noticed my comment and replied. Thanks!

I’ve tried this 5 times exactly step to step and it won’t work😭

Is this the same process for a 2018 gmc terrain?

@PYR-Auto

10 ай бұрын

yes very similar - you can see the Terrain programming video here kzread.info/dash/bejne/d5yIxcGadJawpso.html