1. It's not an inverter as it's input and outputs are both DC. We may call it a step-up DC converter. 2. The description and actual components used in the video different. IRFZ44 is MOSFET as seen in the video description whereas D1047 NPN transistor used in the video. 3. If they used this transistor it needs a base driver stage with another set of transistors which neither seen in the oscillator circuit board nor in the power circuit. 4. D1047 is 200V, 12A NPN transistor, even if it drawing the full rated current (practically not possible) of the transistor the maximum capacity would be 12*12*4= 576Watts only. Whereas it says 6000W. 5. From the picture guess the output bridge diode is rated for 1Amp only. If we load it for a continuous current of 0.7Amps (still the power dissipation by the diodes would be about 4Watt), it can have the maximum capacity of 220*0.7*4=616Watts only. 6. Don't think the guage of the wires used at the DC power side can handle more than 10Amps. Even if we assume 10A, the capacity of the converter would be 12*10= 120Watts only. 7. Need to understand the switching frequency to comment on the capacitor sizing at the output side. 8. Understand it is only a promotional video for the PCB supplier..

@vermilionssj9081

2 жыл бұрын

Thank you very much Sir, I was wondering because the wires are so small hahaha

@maycolmedina6074

2 жыл бұрын

@@vermilionssj9081 I was wondering the same thing, it seems strange that at the end when he turns on the hair dryer the multimeter is off. Probably because the voltage dropped.

@spudhead169

2 жыл бұрын

This channel needs to reported and deleted. Fake crap needs to be punished.

@user-rp6pi6bf3r

2 жыл бұрын

كل ملاحظاتك صحيحة

@santhoshmathew8656

2 жыл бұрын

@@user-rp6pi6bf3r Hello Saeid Hawasili, Could please write in english, I am unable to follow your reply... Sorry...

Very excellent your own 3d wire work, and yet at a glance it seems 200w class dc-dc or ac if pwm.

This is a stabilized voltage booster. Well presented, thanks for the information🌹

6000вт/12в не тонковаты ли провода для 500 ампер? 😉

@geodez86

2 жыл бұрын

Вангую, сборка для демонстрации, но не для постоянной работы 👻

@ToIIIko1

2 жыл бұрын

D1047- напряжение эмиттер коллектор 140в/12а, в схеме в два полупериода -4х12а. На выходе инвертора диодный мост с конденсатором, при нагрузке больше лампочки-жесткая просадка. Про какие 500амер речь?) 🤣

@user-cm2jp1jj7l

2 жыл бұрын

Фен для волос 2000 Ватт. Ну и насмешил😀😀😀!! Даёшь строительный фен на 2000 Ватт?

@68russia68

2 жыл бұрын

@@ToIIIko1 500А это потребление самого преобразователя наверное 😂

@ohmygodisaprettyfalcon

2 жыл бұрын

Лохи смотрят, ведутся, просмотры растут, денюжка капает. Это новый вид цыган - техноцыгане.

Video yang sangat berguna 👍

Messager. Very professional

Top de mas muito bom

lista de componentes porfa, gracias por tu aportación y saludos

Sangat kreatif sekali...

In PCB we trust!

You use mica, as an insulator between the transistor and the heatsink. But as you use a metal screw and nut connected directly to the transistor. The use of mica is pointless in this case. With mica, you must use thermal paste. A very tiny amount, not gobs! to aid the heat transfer between the mica and the metal. The paste fills in the gaps in the rough surface of the mica and metal since air doesn't conduct heat. Again THE USE OF MICA is NOT as a substitute for proper thermal paste.

@harakumarghadai7828

2 жыл бұрын

but the small bolt is connected in the rear to the heatsink panel

@afre3398

2 жыл бұрын

@@harakumarghadai7828 That has nothing to say as the bolt threads will be the point of of electrical connection and the nut clamping down to the tab of the TO package. You use mica if you want the transistor it self isolated from from the heatsink.

@TheCerovec

2 жыл бұрын

@@harakumarghadai7828 that's what he is saying. This transistors are "hot" to ground. That's why he used mica between them and a heatsink. But when he put a metal screw he made that insulation useless. Ok you can center them carefully to not touch the screws with their ground but it's not how it's done. Either you use a nylon screw. Or you use a nylon washer with a lip that drops in to the mount hole on the transistor and a nylon nut. And yeah,mica without thermal paste doesn't work. No thermal transfer to the heatsink.

@nonamedelete9132

2 жыл бұрын

The transistor isn’t touching the screw. The screw only touches the plastic body of the transistor.

@abdulqureshi9436

Жыл бұрын

Ll Llpl

I wish Maplin were still about, I bet they could knock out a good kit for one these.

Hello, nice video ! maybe you can help on the following : My victron Phoenix Inverter 12v 750va just doesn't want to start, no led, no noise... I decided to open it and everything seems to be fine : the 3 30A fuses, the small fuse in the switch circuit, all mosfets and diodes. I basically see no short anywhere. It seems more of on open circuit somewhere as no voltage go to the drive board. Any idea where to look at ? are there any other fuses ? Thank you

Good job😍🆙🔥

Are 6000W the calorific value of this circuit? Multimeter shows DC and it looks like there are rectification diodes on the output, so where is it sine wave. All circuits are simple push pull inverters with exaggerated or wrong performance data, sorry.

@afre3398

2 жыл бұрын

I agree I think even 60 watt is to much to hope for.

@santhoshmathew8656

2 жыл бұрын

@@afre3398 1. It's not an inverter as it's input and outputs are both DC. We may call it a step-up DC converter. 2. The description and actual components used in the video different. IRFZ44 is MOSFET as seen in the video description whereas D1047 NPN transistor used in the video. 3. If they used this transistor it needs a base driver stage with another set of transistors which neither seen in the oscillator circuit board nor in the power circuit. 4. D1047 is 200V, 12A NPN transistor, even if it drawing the full rated current (practically not possible) of the transistor the maximum capacity would be 12*12*4= 576Watts only. Whereas it says 6000W. 5. From the picture guess the output bridge diode is rated for 1Amp only. If we load it for a continuous current of 0.7Amps (still the power dissipation by the diodes would be about 4Watt), it can have the maximum capacity of 220*0.7*4=616Watts only. 6. Don't think the guage of the wires used at the DC power side can handle more than 10Amps. Even if we assume 10A, the capacity of the converter would be 12*10= 120Watts only. 7. Need to understand the switching frequency to comment on the capacitor sizing at the output side.

@afre3398

2 жыл бұрын

@@santhoshmathew8656 Maybe you are right. The moment I saw this video, I knew it was a something done by someone who do not understand electronics. It is a scam and a hoax. And that is all I need to know

Banyak Trafo Kecil... , Bisa di ganti satu Trafo yang besar.... Tapi kelemahan inverter adalah banyak mengeluarkan panas karena tegangan di rubah dengan batas yang tidak wajar... 12V/24/DC ke AC 220V. tapi panas di elektro bisa di dinginkan dengan headsink dan di beri kipas...

Very good tutorial on how NOT to solder

Excellent project

@frazet875

2 жыл бұрын

That what we can see - 6kW its a lie.

Ele é de 24vtts na entrada?

Puedes compartir el plano porfavor? Y los componentes o materiales Se le agradecería muchísimo

nice work

Harika bir canlısın 👌❤

Yes Invertor 👍 ⚡🔌💡

Awesome!

Автор.. давай собери инвертор на 20 киловатт.. и чтобы питалось от маленькой батарейки..

@Denusos

2 ай бұрын

It is not possible to reach 6000W with these components. Physics and mathematics cannot be deceived.

@maycolmedina6074

2 жыл бұрын

Everyone time that I see such claims in the title of the video I know it's fake.

@pavelbogomaz

2 жыл бұрын

@@maycolmedina6074 clickbait was not the best invention of mankind

@tform1

Жыл бұрын

Зато эта схема, если её включить в сеть, может потреблять 6000w. Правда, тоже очень недолго.)))

@parameswarat3031

Жыл бұрын

How reply me sir please.

@EMHard-sr1ej

Жыл бұрын

Saw the schematics aint.complete

How your meter shows 6:41 0l while connected to the inverter and what about the relay sound?

Цука вот люди, бред снимут, назовут красиво и рубят просмотры.

Good information bhi 👌👌👌👍👍👉

Muito bom, mas nesse caso é onda quadrada né..

Cuando coloca el secador de pelo apaga el multímetro digital para que no se vea la caída de voltaje a demás los cables son muy finos para conectar el secador

I'm new at this and want to build one do you have a lost of the parts amd circuits that I would need to follow your video amd make one with my son outselves

Great invention, big congratulation on this nice work. Why you don't mention all we need to create this inveter so as to help many of us. Please, I need it specially. Where I am, I can't command the circuit boards, if it possible give me a little push by helping me design the circuits even by a plan please

@joewoodchuck3824

2 жыл бұрын

Look at the links given.

@afre3398

2 жыл бұрын

No do not do it. It is a scam. You will never be able to get a 6000 Watt output with that contraption. Do not use any time or money on it

@imadsayyed8354

2 жыл бұрын

You know it’s not helpful your time went for nothing

@MorgothCreator

2 жыл бұрын

Do not fall for this type of crap is misleading and very dangerous, a small mistake can end with your DEATH.

Very Nice Go A Head

What frequencey is the primary side of transformer .

Mantap,,,

Very nice bro

İt does not give sine wave output, it gives DC. Diodes, capacitor, and sg3525/ tl 494 pwm, reactive power control driver 😁😁

@joewoodchuck3824

2 жыл бұрын

There aren't any rectifiers for the output, nor would the output transformer pass DC.

Excellent video. Design is a work of art. Can you provide Garber file and parts list?

Where is the thermal grease for mosfets?

good video but where to purchase pcb and components ?

Hello, can we replace these in the scheme? IRF3205 / FTP08N06, MOS-N-FET, 55 V, 110 A, 8 mOhm, 200 W??? what are the capacitors and boards you put in? Parameters?

Really impressive work; BUT.... does it work? can you show us?

Just one draw back with higher frequency inverter is the induction load cut the magnetic flux dropping the voltage

Que modificación necesitas para que trabaje a 60 hz

Nice trick, you did not turn on the voltmeter display to show us the output voltage while running both the bulb and the hairdryer. It would be fun to reveal the output that way we could be convinced that your project is producing at least 5000 watts 220 vac

@sxmtaekwon-do7685

Жыл бұрын

can't be, looking at the transformers.

Qual é a descrição dos transformadores para comprar no site indicado, mas tem que ter opção para 110 e 220V? E a placa que placa é esta aí que não está no esquema?

@MrGuilhermeBG

2 жыл бұрын

Aparentemente ele usa quatro pontes retificadoras de onda completa na saída

@carlosvescio6552

2 жыл бұрын

No pierdan tiempo con esto. Es un fraude

For your usa audience a change list for 120 v 60 cycle would be well liked

@jamess1787

2 жыл бұрын

The small board generates the cycle. Use a 2:1 transformer for 110-120vac?

@MorgothCreator

2 жыл бұрын

This is a continuous current output is not sine wave and CC can bring you the Darwin reward.

@kasunpriyankara7892

2 жыл бұрын

U very very veri by every very

I like this video because he use colorful cable

Thanx

mantap, bisa buatkan pure sine wave 2000watt?

What the connections of transformators ?

HI,good effort,can you make 5kw inverter for soler panel.i am wait your thanks.

Para decir que el circuito entrega una forma de salida sinusoidal, tendria que haberla mostrado en un osciloscopio, yo veo este video y me parece falso...

SUPER

Preciso de um esquema de entrada de energia e s ,e enteada de bateria, tipo quando tá bateria não tá energia e quando tá Energia, não tá bateria,é visse versa.

This circuit does not give singwave out put the out put is DC, you must show the circuit, the shape of out put wave form that is signwave wave , then show the power out put that is 6000 watt.

Dude.... This is awesome! I'd love to know if there is a complete kit that you can buy to make this? Also, the 12v input, how many amps were going in? What was the 12v power source? Li-Ion? Lead Acid? Thanks. Oh yeah, Need it for 120v @ 60Hz.

@TerryClarkAccordioncrazy

2 жыл бұрын

It's fake. If it was outputting 2kW then 170 amps would be drawn from the 12V input. The wires would need to be the size of your fingers.

@MorgothCreator

2 жыл бұрын

Is a continuous current output inverter with an output capability of maximum 300W maybe, continuous current at that voltage can very easy bring you the Darwin reward.

@dolejspavelnevim9409

2 жыл бұрын

Source 😁 free energy generátor made in pakistani

Si se puede hacer electrodomésticos inalambricos y todo lo demas

👍👌

It has no 6kw for sure, maybe 1kw. It has no dead time for tranzistors, cant see spwm microcontroler, only ne555 which is just simple timer not designed for such a designs. No snubber circuits so tranzistors will burn soon. Regards

Aha-ha 6000 watts, a 100-watt light bulb, the voltage sags up to 206 volts, this unit holds a maximum of 2200 watts under load. At least 4 mm square copper wires were soldered for decency.

👍

Hola buenas noches necesito un poco mas de informacion gracias daría un buen aporte

7:22 вольтаж где? По лампе видна просадка

@user-cm2jp1jj7l

2 жыл бұрын

Ага. Ещё спецом отключил прибор, чтоб никто не догадался. Но для знающих и так всё понятно.

добрый вечер. весьма классно. Супер. Хочу повторить схему. Вы могли бы дать схему и какие используются радио компоненты. И печатку Спасибо.

@olegs6294

2 жыл бұрын

Купите в магазине 200Вт инвертор, будет мощнее и надёжнее этого Г

You make great videos. Why are you lying to your viewers? it's not 6kw more like 0.5kw

👍👍❤️❤️❤️👍👍

Se ve muy bueno, pero el sitio web no esa habilitados.. mala cuea....!

What about the wave form, is it Sin wave or Square wave? and how much output frequency?

@scienceguide3880

2 жыл бұрын

If you see the transformer you will know what freq need. It is BASIC. Iron core transformer freq at 50-60Hz and ferrite core transformer run at 30-50khz. In this case it is ferrite core transformer

@MorgothCreator

2 жыл бұрын

It is a continuous current output inverter that at a small mistake can bring you the Darwin reward.

You connect all the bases and emitters in parallel with really long length of wire, this is not good because the longer the wire, the more it will ring. Also you need proper heatsinking or use MOSFETS with proper driving

Senoide modificada?

What is input current value of DC Ampere.? Here we know 12v but Amp...?

@afre3398

2 жыл бұрын

It is given in the wattage. If we assume an ideal world (in which this contraption actually will work). The energy input will be equal to the output energy. wattage P is equal to voltage times current (P=U*I) and hence the input current will be equal to 6000/12= 500 Ampere. At this point I hope you do understand that this contraption probably hardly may be able to output 60 Watt. It is a hoax and a scam. Do not use any time or money on this project.

Can you show me how to make a nuclear power plant using nothing but 12ga wire and 2AA batteries next?

chế chạy quạt dưới 60w thì đc. Chứ sài cho động cơ cỡ 200 trở lên, chắc sài đc mấy bữa. Hài nhiễu kiểu này động cơ nào chịu nỗi.

Can u tell me the parts .. Where to buy

from the size of the transformer that is a total of 2000w inverter not 6000w. that ferrite is either EE33 0r EI35 which is max of 300w-500w each

Disculpa no puedo entender los diagramas le falta explicasion

👍👍👍itu beli kompenennya di mana apa bisa pesen

It's not sine wave and it sure isn't 6kW. It would be an educational project if you didn't lie.

@AjilSathyanLMCEC

2 жыл бұрын

Actually it's square wave. We can't use this to other home appliances. Motor appliances must need sine wave otherwise motors get damaged

Yeah that's great for where you live 220 volts I live in America where everything is 115 or 120 how's this helped me.

@user-sd9tt6eo9h

2 жыл бұрын

У вас есть 220. Между 2 фазами. Ничего тебе не мешает сделать 110или 120. Возьми любой свой трансформатор

@bijikucing375

2 жыл бұрын

@@user-sd9tt6eo9h that's right.. 👍

@bijikucing375

2 жыл бұрын

Yup, asian using 220v bro🤣

Ciao amico 🤝🔋🔔👍

salve si potrebbe avere lo schema completo grazie mille

out put 220 AC/DC?

Все транзисторы из разных партий. Мда..........желаю удачи...........

ทำไมไม่บอกค่า r ด้วยจะได้ทำเป็น

Hello, can you use transistor ITF3205? with the same scheme?

@inventorkr1

2 жыл бұрын

yes

what are the circuit board name and parameters please?

Уважаемый блогер, опубликуй просто схему. Принципиальную схему этого аппарата.

@sergeysakevich3515

2 жыл бұрын

Так точно, напрягает вся эта видеохрень с паяльником, дай схему и всё будет понятно.

@Viktor-yj2ns

2 жыл бұрын

Она за кадром 🧐, всегда 🤔

@fantom3ds

2 жыл бұрын

Он правильно сделал что не показал схему. Не стоит она повторения, поверь. Говнина еще та. Есть получше схемы и проще в разы, на той же IR2153. Да даже эту можно сделать лучше, если на полевиках, да с обратной связью, но там лепить дополнительные затворные разряжающие транзисторы и задействовать усилители ошибок, платка с микросхемой уже будет не такая маленькая

Plz sir rechargeable battery 12v to 220 inventor make video 20w led tube light rechargeable inventor

Is this pure sine wave

художественная пайка навесом

D1047C Datasheet - 140V, 12A, NPN Transistor ~ 80watt *8 = 640 Watt Max

@inventor kr how can i set-up this as permanent converter or inverter

@inventorkr1

11 ай бұрын

Thanks for your comment! We recommend following the steps outlined in our tutorial video to help you set up this converter or inverter as a permanent solution.

Please send to me the circute diagram of 6000w inverter

Tensão é dc na saída e não ac assim não podendo ligar trato e motores , secador motor a dc por isso funcionou.

Perché onda sinusoidale, è il tester legge una tensione continua?

I would love to know how you get 6000 watts at 220 volts from 1 amp transformers.

@Radioman.

5 ай бұрын

From the lightning bolts of Zeus, cause it isn't coming from those puny transformers.

May be 600 w . Power input cables wery thin

How can I download this pcb?