Best and detailed silicone mold making video. Thank you!

@zimmtex

Жыл бұрын

Thank you, I'm glad it was helpful!

Absolutely awesome idea! I have been dealing with the same issue of maring the wood. Thanks for sharing this idea! Im going to have to make a pair for my vise.

@zimmtex

11 ай бұрын

Yes, it wasn't too much work and now I use them all the time.

Nice one Zimmy, thanks for sharing this tip. Another great video to go with all the rest you do. Cheers from Down Under.

@zimmtex

2 жыл бұрын

Thank you very much!

Yeah this is way better than jamming some old rags in between the vice lol

@zimmtex

2 жыл бұрын

I've done that too!

Not gluing the leather enables you to replace the leather as it wears out. Great video.

@zimmtex

2 жыл бұрын

Great point, thanks for your support!

Magnífica idea. Intentaré imitarla. Muchísimas gracias por compartir tus excelentes trucos.

@zimmtex

Жыл бұрын

Thank you very much!

Great idea and a fun little project too👍.

@zimmtex

2 жыл бұрын

Thanks, I'm excited to use it. It's always a pleasure working with good tools.

Amazing idea

@zimmtex

2 жыл бұрын

Thanks!

Nice idea, I had my doubts about not including the thickness of the leather in your calculations, but the water and clamps proved me wrong! Thanks for sharing!

@zimmtex

2 жыл бұрын

Thanks for watching!

that works well

@zimmtex

2 жыл бұрын

A much needed upgrade! Thanks for watching!

Great idea as always. I'll make the same construction. Thanks for sharing.

@zimmtex

2 жыл бұрын

Thank you for watching! Good luck on your build.

Brilliant! Thank you@!

@zimmtex

2 жыл бұрын

I appreciate your support!

I tried the cutting board method too, but got marks on soft wood too. I tried using Pyrex container lids because they are featureless but not thick enough for my liking, so this leather idea is great!

@zimmtex

2 жыл бұрын

Thanks, I'm glad you found this interesting!

Ok I’m doing this

@zimmtex

2 жыл бұрын

Thanks!

👍👍👍👍👍👍

@zimmtex

8 ай бұрын

Many thanks!

👍

@zimmtex

2 жыл бұрын

Thanks!

I really enjoy your channel. I learn a lot from you. Thanks for sharing your expertise🙂🙂 Quick question... I tried using forester bits to make weights like the ones you use to balance lures but I couldn’t remove them from the wood mold. I used oak. Different sized bits 3/8” deep. Did you prep the mold with something first?

@zimmtex

2 жыл бұрын

Thank you for watching! Sometimes I have a few stubborn holes that won't release very easily. I don't prepare them, but they do seem to release better after a few uses. I think the hot lead burns the wood slightly and makes it release better over time. If it still won't release after cooling and vigorous banging, you might try a softer wood with more flex in it. I've been using pine. Hope this helps.

@waterdoglures1352

2 жыл бұрын

@@zimmtex Thank you. I’ll try a piece of pine. 🙂.

👍👍👍👍⭐️⭐️⭐️⭐️⭐️🐠🐠💜😘

@zimmtex

2 жыл бұрын

Thanks!

Hello master i wish you could read my comment in your video.. a month ago

@zimmtex

2 жыл бұрын

I'm sorry if I missed your comment. I try to respond to all comments. I have looked back and cannot find it.

@MASKTERTV

2 жыл бұрын

Your vid about water slide decals..

@zimmtex

2 жыл бұрын

@@MASKTERTV I did reply; sorry you did not get it. I use small paint brushes to apply epoxy. The best epoxies I have used are TrueCoat and East Coast Resin. Those are both really smooth and have very few bubbles. Best wishes!

Thousands of lifetime projects with woodglut plans.

@zimmtex

Жыл бұрын

Thanks!