How to Make Cheap Single Cell Battery Powered RC Airplane.. Homemade Airplane
Тәжірибелік нұсқаулар және стиль
Can the entire system including the Motor, Servos and receiver be powered by a single cheap 18650 3.7 volt battery?
How To Build The Simple RC Airplane That Can Fly With 3.7V Single Battery.
* 20A ESC: s.click.aliexpress.com/e/_DFg... OR
www.banggood.com/custlink/mvv...
* 9gr Micro servos: s.click.aliexpress.com/e/_DDe...
* 5gr Micro servo: www.banggood.com/custlink/mGD...
* 1.2mm Pushrods: s.click.aliexpress.com/e/_Ded...
* Servo control horn: s.click.aliexpress.com/e/_DmJ...
* DC 180 Motors : s.click.aliexpress.com/e/_Dd1...
* 108mm Propellers (CW&CCW): s.click.aliexpress.com/e/_DeI...
* Radio control system: s.click.aliexpress.com/e/_DCP... or * tr.banggood.com/custlink/vvGE...
* Micro receiver: s.click.aliexpress.com/e/_DEX...
(18650 Battery 1500mAh+ & 4A+)
* 18650 3.7V Battery : s.click.aliexpress.com/e/_Dno... OR www.banggood.com/custlink/KDG...
* 18650 Charger: s.click.aliexpress.com/e/_DEI...
* Hot melt Glue Gun: s.click.aliexpress.com/e/_DkC... OR
s.click.aliexpress.com/e/_DnD... OR s.click.aliexpress.com/e/_Dl2...
* JST Connector&Cable: s.click.aliexpress.com/e/_DmT...
* Cable Tie: s.click.aliexpress.com/e/_DBI...
5mm kraft foam board
3mm insulation foam
2mm balsa sheet
Diagrams for dimensions: tinyurl.com/95mc2hjh
Technicial Specifications:
Wing length: 88 cm
Body length: 65 cm
Wing area: 1056.00 cm2
Flight weight: 192 g
Center of gravity (CG): 4.7 cm - 5.3 cm from the front of the wing
Vbar: 0.86
Motor: DC 180 Brushed
Battery: 18650 3.7V
ESC: 20A Brushed
Remote control: 3 channels or higher and 2 micro servos
Approximate flight time (for 2600mAh) : 20-25 minutes (in ideal conditions)
#rcairplane #diyairplane
All of my videos : bit.ly/2Z9QVYK
Thank you for watching. Please Remember to Share and Subscribe for More Amazing Videos.
Пікірлер: 243
I loves watching these vids as a kid, now that I'm a electronical engineering student, this is even better to watch!
omg man hearing that ESC beep beep beep from the brushed motor gives me so much nostalgia from having my slow flyer propelled with Mig 400 motor, I'm glad that I got to learn using BLDC motors but damn this is really cool and nice little build for beginners
@vidhush02
Жыл бұрын
exactly so much memories
Nice build and flight,hats off to you👏🙇
Nice job, sir. Thanks for sharing.
Brilliant design and great video !
I've done a Couple scratch builds also , and they are always fun. Also there is no soul crushing heartbreak when you crash, because you can just easily fix it or just build another one.
@therobloxyoutuberfunny
2 ай бұрын
Please help me how to build a perfect balanced plane with a fly robo kit 😅
that was a great video Thanks!
harika oldu.. teşekkürler ve tebrikler...
Enjoyed that thanks even like the music
Good flying airplane !
nice work.
Lovin it!
I pushed like before I saw it!
Eline sağlık...
Neat! Tall grass is your friend there in he end. Of course its so light and slow that it would be hard to destroy it.
Wow! Maybe I will make it
abi muq olmuş herzamanki gibi
Gerçekten mükemmel ! Sadece 3.7 volt ve bir şaheser
How do I thank you for this? Now I WILL build a plane.
Anda luar biasa...., Saya berharap lain waktu anda membuat rc glider atau slow flyer dengan bahan depron menggunakan dc motor, pasti itu akan sangat menarik, terima kasih
So cool ❤
عمل رائع واصل ❤️♥️🌹
Nice... 👍👍😁😎
Başarılı 👌
Muy bueno! Usas la 18650 como bateria en lugar de las Lipo..... Yo tambien las uso y van de maravilla. El diseño del modelo le *Aumentaria el Diedro y la distancia entre el ala y el estabilizador de cola* ..Asi seria menos Nervioso... Salgo a volar! DX
You are a genius!
@Zghost276
Жыл бұрын
The people who invented rc are genius
Amatörler için çok ideal bir alıştırma modeli olmuş eline sağlık👍
Çok güzel uçuyor tebrikler...
@aquaonx8784
Жыл бұрын
npc
Amazing
Gonna make this ❤ .
super❤😮
I dig slow fliers.
very inspiring !
This plane is flying quite nicely. Of course, it is a lot of work and requires a lot of know how.
Me and the kids are lapping this up. They'll get building and we'll show you what we've built based on your inspiration
@therobloxyoutuberfunny
2 ай бұрын
Did u build it buddy?
İlk yorum benden olsun 😊 aga yine yapmışsın yaa 👍
Great, Please make coreless motor plane, thank
Çok büyük hayranızım tebrik eder ve daha çok video yüklemenizi sabırsızlıkla bekliyorum...
@RohitKumar-kc2pq
Жыл бұрын
Which language are you taking bro/sis
@MalKediler
Жыл бұрын
@@RohitKumar-kc2pq Turkish
👍👍👍
Hey I've been watching your videos since long and it's really great.. i've a question, does the motor create all the thrust or the large wings inclined at an angle with the horizontal axis contribute some upward lift too ?? I'd be grateful if you answer
@Kendin-Yap
Жыл бұрын
The motor provides the propulsion. As long as there is thrust in the forward direction, the lift force of the wings occurs in the upward direction. But after the engine stops, some more gliding continues.
Thanks❤❤❤ i can make this plane into my budget😅❤
@adityabaghel729
Жыл бұрын
ye dukh kahe khatam nahi hota be 😢
THANK
❤
VERY NICE! why didnt you cover the bottum side of the wing? withiot this cover the lift is damaged and making a lot of turbulence on the wing.
@Kendin-Yap
2 жыл бұрын
Thanks.. I made this to be lightweight. In addition, this (Concave profile) allows it to fly at very low speeds. It is not wrong to have an open wing.
Wow
can i use 105mm for propeller?
Abi bu tarz videolara devan
Do you have a video with the files for making the clamp that you used to hold the motor while you soldered it?
Well how much amp will it draw ? And I found some 180 motors that look almost the same as yours . But one has FK-181PH written on it , another one has FK-180PH . Which one will be better ?
Çok güzel bir video olmuş... Aynı malzemelerle delta kanat videosu da gelir mi acaba?
Abi selam antalya dan balıkçı ben
Sir, can I use that DIY rc transmitter and receiver in this project that you have taught how to made it earlier ?
@Kendin-Yap
Жыл бұрын
It is a little heavy. This model has to be very light.
Abi ben Arduino ile kumanda yaptım 3 km ye kadar basit RC uçak uçurdum fakat şimdi 2.38 boyunda yapicam 2 kg a yakın bir ağırlık var 2 adet 1400 kv motor ve 1045 pervane ile kaldırabilir mi acaba ?
Hi..nice build. I have a question..so rhe micro receiver u used in this build it paired up to your flysky radio even though it's not a flysky receiver??? And that being said I'm guessing you bind that receiver to your flysky radio the same way you bind a flysky receiver to your flysky radio??thanks....
@kushanvimanka8323
2 жыл бұрын
FS2A four channel receiver is using AFHDS 2A protocol so it can be bind with flysky transmitters, I also having it and works really well.
@Kendin-Yap
2 жыл бұрын
Yes, a receiver (FS2A) for Flysky radios. Matches like other Flysky receivers.
@spottyjack614
2 жыл бұрын
@@kushanvimanka8323 I have to get me a couple of these FS2A receivers for my fly sky radio do u have a link to were to get them?? If not I'm sure I can find umm somewhere?? Just thought I'd ask...thanks
Интересно, но такое впечатление, что управление осуществляется с помощью ветра :)
I have a question since I have been planning on following this build for my project. Will the 20A esc work on a single 3.7v battery ? the product specs say it takes 4.8v-7.6v and this has confused me a bit. Also, does the ESC have a BEC to power the arduino based receiver? Its hard to source smaller bldc motors where I live and I want my build to be light enough to work off a single cell. I am also planning on trying make an rc car from a die cast model (bigger than hot wheels so space is there for arduino and everything). Hope you see this and reply.
@Kendin-Yap
8 ай бұрын
When the 3.7V battery is fully charged, it is 4.2V. This ESC can work up to 3.9V. BEC available. But your receiver and servon must also be able to work with low voltage. The ones I used in the video can work.
@nichtolarchotolok
8 ай бұрын
@@Kendin-Yap THANK YOU SO MUCH for the reply. I just got the batteries and ESC in the mail and tested and it works. The concern i have is if the Arduino based receiver I'm planning on making will work well. My arduino nanos seem to work fine but i am yet to test the nrf24l modules and servos.
I have watched your video many times and followed the guidelines for my plane. I had problems with the radio because I had to hold the "Cancel" key longer to save the configuration. 🙂With 3.7 the engine has no power. Maybe because the other elements subtract energy from the engine? So I put a 7.4 battery in it and it sounds better. But won't the motor burn out? thanks for answering
@Kendin-Yap
Жыл бұрын
When a 3.7V cell battery is charged, it will be 4.2V. It should be fine until it drops to 3.8 - 3.9V. Since the engine will produce high power when 7.4V battery is used, the structural strength of the fuselage and wing of the aircraft will not be sufficient. This model has to be very light in order to fly with low power. Therefore, it does not have the structural strength required for high strength. If you are going to use it with 7.4V, you need to strengthen the wing and fuselage. (Can work with DC 180 motor 7.4v.)
@cesarca1102
Жыл бұрын
@@Kendin-Yap You are very kind to answer. It's clear to me from other answers you've given. Thank you
Elinize sağlık hocam çok güzel olmuş , uçuş süresi nedir acaba. Birde hocam , motorların üstüne lehimlediğiniz 2 parça ne işe yarıyor .
@huseyin985
2 жыл бұрын
2:47 de yazıyor. "elektriksel gürültüyü filtrelemek için."
@esatkdn
2 жыл бұрын
seramik kondansatör. paraziti engellemek için, motor gerisinde olan devreyi korumak için, motorun daha iyi çalışması için felan
@serdar-bayram
2 жыл бұрын
@@huseyin985 Teşekkür ederim gözümden kaçmış, Bazen motor daha güçlü olsun diye buna benzer parça lehimliyorlar acaba odan mı diye sordum bende.
@serdar-bayram
2 жыл бұрын
@@esatkdn Anladım , çok teşekkür ederim.
@Kendin-Yap
2 жыл бұрын
Yeterince cevap verilmiş. Biraz daha açayım. Motorların bobinleri çalışma esnasında elektriksel gürültü (parazit gibi) üretirler. Bu gürültü elektronik devreleri özellikle alıcı gibi devrelerin sinyallerini olumsuz etkileyebilir. Seramik kondansatörler bu gürültüyü filtreler.
i think this is the first 1s li ion plane
Hey u have used 9gr servos which work with 5v but the maximum power supply is at full charge 4.2v so how did they work?
@Kendin-Yap
3 ай бұрын
These servos can operate up to 3.8v-3.9V level. It loses some speed and torque, but that's not a problem for this model.
Hey, so I’m doing this for my science fair and while I was connecting the battery to the esc the esc started smoking. Do you know why? The battery is 4.2 volts - 5 volts, I think that was the issue but I’m not sure.
@Kendin-Yap
Жыл бұрын
ESC supports up to 8.4V. The problem is not voltage.. You must have connected the positive and negative poles wrong. Another possibility is that you may have short-circuited the motor output cable ends. In both cases, ESC burn up.
@crescentcabbage8065
Жыл бұрын
@@Kendin-YapOk, thank you it works now. The only problem is I used cardboard for the whole thing and the plane won’t fly or glide with the wind. It fell and the cardboard body is destroyed any recommendations?
@vidhush02
Жыл бұрын
@@crescentcabbage8065 use deprons bhai
@crescentcabbage8065
Жыл бұрын
@@vidhush02I used the Kraft foam now for the body. Unfortunately, I couldn’t find any 3mm foam for the wings so I thought of using 3mm Eva foam but that bends too much and isn’t structurally strong. The plane still doesn’t glide and falls. Have any ideas what I did wrong and why it doesn’t fly.
Slm fpv drone için farklı kumanda olur mu
Rc plane Boeing make video sir plz 🙏
I cannot believe you left out the all important CG !!!
@mirekfidler3505
2 ай бұрын
It is always 1/4 - 1/3 of wing...
For the Control / Radio system from Aliexpres witch version i need for this plane? because there are a lot off versions
@Kendin-Yap
9 ай бұрын
You can get the one marked "No Receiver". Because you need to buy the micro receiver separately.
👏x💯
Very impressive, how do you land it though?
@luigimario2704
Жыл бұрын
Crash
@luigimario2704
Жыл бұрын
Do it parallel with the ground though
Emeğinize sağlık çok net anlatmışsınız, motor itme açıları her uçakta aynı mıdır? Arkadan itiş fpv modeller için açıkar hangi yönde ve kaç derece olmalıdır?
@Kendin-Yap
Жыл бұрын
Burundan çekiş için genellikle bir birine çok yakındır. Arkadan itiş de ise değişir. Örneğin bazı yapılarda yukarı açı gerekir. Kesinlikle şöyle yapın demek zor.
@emredemirelsworld
Жыл бұрын
@@Kendin-Yap teşekkür ederim 🙏
que receptor é esse ?????
Bizim normal 6 kanal fly sky 3.7 ile çalışmıyor galiba
@Kendin-Yap
2 жыл бұрын
Çalışır ama menzil önemli ölçüde kısalacaktır. Tüm alıcılar için ideal voltaj 5-6V dur. Yaklaşık en az 3-3.5V a kadar çalışırlar ama menzil kısalır. Bunun gibi kısa mesafede kullanılan modellerde sorun olmaz.
First
Merhaba bu uçağın aynısını sadece pili değiştirerek 7.4V 1000mAh pil ile yapabilir miyim?
@Kendin-Yap
2 жыл бұрын
Mümkün ama uçağı biraz sağlamlaştırmanız gerekir. Çünkü 7.4V ile motor gücü baya farkediyor. Kanat altını komple 3mm depron ile kaplarsınız. Ve kanat içine boydan boya 3-4 mm kalınlığında bir çıta koyarak destek yaparsınız.
How can the esc which is rated for 4.8v functions on 3.7v?
@Kendin-Yap
Жыл бұрын
When 1S battery is full, it is 4.2V. And these ESCs have voltage flexibility. It works fine until it drops to 3.8-3.9V.
@coast219
Жыл бұрын
@@Kendin-Yap thanks👍
the video is great but what is the name of that controller, or any controller that does its job
@Kendin-Yap
Ай бұрын
Below the video are the names and links of the materials used. Click or tap "more" to see the entire detail section.
Motor olarak ne kullandınız acaba vidyoda belirtmemişsiniz???
@Kendin-Yap
Жыл бұрын
Videoda mevcuttur. 2:28 ... ayrıca videonun altındaki açıklama bölümünde tüm parçaların isimleri ve linkleri de mevcuttur. videonun altındaki açıklama kısmında "DAHA FAZLA" ifadesine tıklayın.
Hi hello sir
Herşeyiyle çok güzel bir model olmuş fakat fiyat açısından şu ankı kullandığınız kumanda yerine daha uygun nasıl bir kumanda tercih edilebilir
@Kendin-Yap
10 ай бұрын
En uygun fiyatlı kumandalar Analog olanlardır (Menüsü ve ekranı olmayan). 4 kanallı bir anolog kumanda ile temel bir çok model uçak kontrol edilebilir. Markası önemli değil. Diğer seçenek arduino ile kendi yapacağınız kumanda olabilir.
Can you give a link to the foam
Cuanta autonomia tiene con la 18650 ??? De cuantos amperios es ?
@Kendin-Yap
2 жыл бұрын
Current strength should be 10A or above. The capacity varies according to your preference.
Can I make this with 1000kv bldc motor?
@Kendin-Yap
2 жыл бұрын
No, it is not suitable.
Can we make the wings out of foam board as well?
@Kendin-Yap
23 күн бұрын
yes you can
Why not put the servos as far forward as possible?
@Kendin-Yap
2 жыл бұрын
For the center of gravity.
2:29 and 4:45 ) Where can i buy that red and black cable on the battery / motor??? and also at 3:05 we can sea on the motor that black cable with red where can i buy that en how does that fit there??
@Kendin-Yap
9 ай бұрын
I added it to the links. Please check again
@KendinYap. Hi Sir, I'm about to order the parts to build my first airplane, the "Single Cell Battery Powered RC Airplane." Something is calling out to me. The recommended voltage range for the ESC is 4.8V to 8.4V. You're using a single 3.7V cell. How do you explain this? I'll read you carefully before finalizing my order.
@Kendin-Yap
9 ай бұрын
Every ESC has some flexibility in the positive and negative direction. When the single cell battery is fully charged it is 4.2V. The ESC I mentioned in the link works smoothly up to 3.9V. I tested it for a long time and had no problems.
Pil kaç mAh ? Ve ne kadar akım vermeli ?
@Kendin-Yap
2 жыл бұрын
4A ve üstü akıma sahip olmalı. Kapasite önemli değil. Tercihinize kalmış. Çünkü 18650 pillerde kapasite ağırlığı değiştirmiyor. Benim kullandığım 2500 mah
Exactly which airfoil would you be using? :)
Hocam kumandayı kendim yapacagım pcb yide ben tasarliyacagim. Hangi parcalara ihtiyacim var antenli. Nrf kullancam yazar misiniz lutfen
@Kendin-Yap
2 жыл бұрын
Kumanda yapımı videolarımda malzeme listeleri mevcuttur. Onlar size faydalı olacaktır. kzread.info/dash/bejne/lHhr1LObnrbIlc4.html kzread.info/dash/bejne/op520KiTd8nZmqw.html
the ESC and servo not work with less to 4v.
@Kendin-Yap
2 жыл бұрын
it works. The receiver and servos I use work over 3.7V
Atılan uçak olarak da kullanılabilir mi?
@dogukankocak1822
2 жыл бұрын
ağırlık merkezini iyi ayarlarsan olur
6 kanallı kumanda olurmu(flysky)
@Kendin-Yap
2 жыл бұрын
3 kanal ve üstü tüm uçak kumandaları olur
Hl algo en la electronica que no entiendo lo podes aser con un 30 A el esc una sola bateria podes
@Kendin-Yap
Жыл бұрын
6A is enough but 20A or 30A esc is cheaper.
what kind of board did you used for the plane
@Kendin-Yap
6 ай бұрын
Kraft foam board and insulation foam
What is the end build cost?
Merhaba iyi günler, Videonuz da kraft fotoblok kullanmışsınız.Bu maket uçağını bizde tasarlmak icin malzemeleri temin ediyoruz yalnız kraft fotoblok degil strafor fotoblok aldık uçuş için herhangi bir problemle karşılaşır mıyız
@Kendin-Yap
Жыл бұрын
Strafor çok esnek olduğu için rigit bir hale getirmeniz lazım. Karbon çubuk veya benzer bir malzeme ile destekleyebilirsiniz. Özellikle de kanadı.
@kubraaltundas8760
Жыл бұрын
Teşekkür ederim.Kraft fotoblok temin edelim .Maket uçağı uçururken karşılaşacağımız büyük problemler neler olabilir.Yardımcı olursanız cok sevinirim
Hi There....i need your help...i followed the instructions but 5:53 to 7:22. But FC-16X is not remembering the setting. CH3 still goes complete back n forth and not able to see any power to Motor. What am i doing wrong? Could you please guide? Both reciver and ESC have flashing blue (slow) and fashing red and it only makes 1 DO sound.
@Kendin-Yap
10 ай бұрын
If you are talking about FS-i6X, you need to press and hold the CANCEL button for a long time to save the setting.
@venkatratnakar685
10 ай бұрын
@@Kendin-Yap Thanks so much for responding. Got it able to pass that one. But still no power is going to motor. ESD board just makes one DO beep but nothing past that, unlike in your video DO BE MI (7:36 to 7:43). Could you please help, if the issue is receiver board or ESC Board? i ordered another set just in case. Battery is fully charged 4.18v , Now reciever light is blinking slow (so should be connected). Any suggestion will be very helpful
@venkatratnakar685
10 ай бұрын
@Kendin-Yap Could it be the ESC board not working? I just not able to figure out if the receiver is the problem or the ESC board. Shipping is taking time. Any suggestion will be helpful!!
@venkatratnakar685
5 ай бұрын
@Kendin-Yap: Thanks for your help. Realized the issue with Transmitter and Receiver were not binded. After doing the binding process it started working.
What is the name of the material used to make the frame
@Kendin-Yap
2 жыл бұрын
Fuselage: Kraft foamboard. Wing: insulation foam
Selamunaleykum
Merhaba 1 adet dc 180 motor kaç gram itiyor veya çekiyor ortalama 100 mm pervane ile?
@Kendin-Yap
Жыл бұрын
Yaklaşık 140-160 gr
@baykemal7874
Жыл бұрын
@@Kendin-Yap süper, teşekkürler.
Can you give me list and measure? Thanks
@Kendin-Yap
2 жыл бұрын
Materials and links are in the description below the video. Press the arrow symbol on the right below the video. (For mobile) Click the "More Information" link below the video. (For PC)
Whats the weight of that rc?
@Kendin-Yap
7 ай бұрын
192gr