Very interesting video I like your video I will continue to monitor your next video, thank you

すばらしい！！ どこの部位を作っているのかわからない動画が多い中で、こちらの動画は最初に「これを作りますよ」と示してくれます。 最後に完成品を見せる手法と違って、部位ごとに見せていただいた後に作成画面が出てきます。 このような動画を求めていました。ありがたいと思っています。Thank you！

@tiny-cabin-woodworks

5 ай бұрын

動画制作の励みになるコメントありがとうございます。 これからもなるべくわかりやすい動画を制作していきたいと思います。

Thanks for sharing. It's simple, beautiful functional and perfect for the purpose.❤😊

@tiny-cabin-woodworks

5 ай бұрын

Thank you for your comment. Your comments were very encouraging to me.

Buen trabajo....👍👍 🇵🇪

Здравствуйте! Я новичок в этом деле! Для меня очень познавательно и очень доступно! Красивая работа! Очень просто у Вас получается, думаю, у меня тоже получится!!!! Огромное спасибо за проделанную работу!!!! С меня лайк и подписка! Слежу дальше за Вашими работами!!!!!

@tiny-cabin-woodworks

10 ай бұрын

Спасибо за ваш комментарий. Я рад, что это было полезно.

Thanks!

@tiny-cabin-woodworks

3 ай бұрын

Thank you for your support. This will encourage me to create future videos.

Nice

RẤT HAY ,,TIẾP TỤC SÁNG TẠO BẠN NHÉ

A very nice, cleverly designed tool that looks easy to replicate. There are many variations on this type of jig, and NONE of them address one particular item: The cutting tool that you use to machine the thinner board to width, at 2"21, and 3"38 is the ONLY cutter to use when using the tool, so if you used a 1/4" cutter at the beginning, you must always use a 1/4". If, for some reason you want to use a 1/2" cutter, you must make new boards cut to width with a 1/2" cutter

Hola, muchas gracias por el video, está muy descriptivo y fácil de entender, Felicidades!

Die werde ich nachbauen

Thanks for the video, the JIG you built is very effective and easy to use. But I have a doubt. At minute 13.53, you make a bit change, I assume that the width of that bit is the same as that of the previous bit, otherwise the JIG would have been modified. Could you confirm this. Thank you

@tiny-cabin-woodworks

5 ай бұрын

The bit I replaced is a top bearing pattern bit with the bearing attached to the base of the bit. Originally, this jig can only be used with specific bits. In that case, press the side of the base of the trim router against the guide plate on the top of the jig while cutting. In the case of the replaced top bearing pattern bit, cutting is performed while pressing the bit bearing against the guide plate (thin plywood) at the bottom of the jig, without pressing the side of the base of the trim router against the guide plate at the top of the jig. It is possible to perform cutting without changing the jig. *The bit diameter of the top bearing pattern bit must be larger than the diameter of the specific bit. Sorry for the lack of detailed images of that part in the video.

Hi Great looking dado jig, please can you let us know the measurements for this jig

@tiny-cabin-woodworks

6 ай бұрын

Sorry, we are currently considering releasing the drawings and dimensions of the jigs, etc.

Очень полезное видео, постараюсь воссоздать для себя!👍🏻👍🏻👍🏻. Какую фрезу используете в этом видео?

@tiny-cabin-woodworks

7 ай бұрын

Спасибо за ваш комментарий. В видео используются фрезы (биты) стандартные прямые, спиральные (используются для обработки сквозных канавок) и сверла с подшипниками.

After you make this jig, are you only able to use the size bit you cleaned up the 1st two edges with?

@tiny-cabin-woodworks

13 күн бұрын

In addition to the two-edge cleaned bits, you can use top-bearing pattern bits. (Top-bearing pattern bits are bits with a bearing at the base of the bit.) However, the diameter of the top-bearing pattern bit that can be used must be larger than the diameter of the two-edge cleaned bits.

Hi Great work, what is the name of the router bit that you used to make the slotting? Already subscribed and have you on favorites. Thank you :)

@tiny-cabin-woodworks

10 ай бұрын

Thank you for subscribing! The name of the router bit I use is Spiral Bit. www.btmt.jp/SHOP/168781/list.html

@Ontopworld2011

10 ай бұрын

Thank you for the quick reply :) Unfortunately it's all in Japanese and when I look at Amazon there is a spiral up cut and a down cut. Not sure I presume it's the down cut? Thank you

@tiny-cabin-woodworks

10 ай бұрын

Down-cut spiral bits are used in the video.

@JulienThomasNZ

Ай бұрын

The direction of the cut will help expel the cut sawdust. So for a shallow cut use an up-cut spiral bit to push the dust up. A down-cut spiral bit will push the dust down which is useful if your router bit is going all the way through the wood. You can buy combination spiral cuts, where the bottom of the bit pushes the dust up and then the cut transitions to a downward cut at the top of the bit. This is useful if you are making multiple passes and slowly lowering the router cut with each successive pass. Hopefully I explained that well enough. 😊

genial!

I hope you write the wood measurements in the comments box so that we can also benefit, please

@tiny-cabin-woodworks

8 ай бұрын

Thank you for your comment. I would like to consider it.

What size of plywood are you using to make the jig?

@tiny-cabin-woodworks

8 ай бұрын

Thank you for your comment. We are currently considering disclosing the details of the dimensions.

И как часто такие соединения приходится делать?

Bonjour, je suis vos vidéos avec passion depuis quelques temps . Partagez-vous les plans de votre réalisation de votre gabarit de rainure. Vous remerciant par avance. Cordialement

What are the names of the threaded rod, handles and aluminium groove parts? Where do you source those?

@tiny-cabin-woodworks

2 ай бұрын

The parts used in the video are M6 T-bolt (for 19mm T-slot track), handle with M6 screw hole, and T-slot track 9.5mm x 19mm. It's Amazon Japan, but I'll post the product link. M6 T-bolt　amzn.to/4armsde handle with M6 screw hole　amzn.to/43IMbvh T-slot track 9.5mm x 19mm　amzn.to/4cA1wCu

What is the model of that Makita router?

@tiny-cabin-woodworks

11 ай бұрын

This model will be the RT50D sold in Japan.

自分ではできないので販売したらどうですか？

@tiny-cabin-woodworks

11 ай бұрын

コメントありがとうございます。 検討してみたいと思います。

Could anyone help me with a name or a link to the channel that holds the head of the bolt please?

ビットサイズは１つに固定して使う治具と考えてよいのかしらん？

@tiny-cabin-woodworks

Жыл бұрын

治具加工時に使用したビットを使用するのが基本ですが、そのビットより大きい径のトップベアリングパターンビットを使用すると、治具を同様の使い方で同じ溝加工が出来ます。

@oyoyo8817

Жыл бұрын

@@tiny-cabin-woodworks 大きい径の場合は、治具をベースプレートのガイドとしてではなく、ならい彫りのテンプレートとして使うような意味合いになるということですか？

@tiny-cabin-woodworks

Жыл бұрын

今回の動画でも終わりの方でそのような使い方を紹介しています。

@oyoyo8817

Жыл бұрын

@@tiny-cabin-woodworks ベアリング径が太くなればその差分だけ、際に彫り残しが出るので、初めにガイドをその分だけ幅広に取ってやれば、ぴったりになるということですね。ありがとうございました。