How to make 90* elbow with Duct Board
Hey guys in this video I demonstrate how to make a 90* elbow out of duct Board using a speed square and template with 22.5 degree angle. Please Like & Subscribe
share.getjobber.com/mzrzvqe
Jobber is the tool I use to book more work, schedule smarter, and get paid faster. Sign up today for a 2 week free trial.
More videos down below 👇
Malco FasGroov Shiplap Tools For Duct Board review/demo
• Malco FasGroov Shiplap...
How to cut Duct Board W/Amcraft Layout Square /V-Groove method
• How to cut Duct Board ...
Cutting Duct Board W/ centerline method using amcraft tools
• Cutting Duct Board W/ ...
HVAC Install: Rough-in Day
• HVAC Install: Rough-in...
Milwaukee Packout HVAC Installer Edition
• Milwaukee Packout HVAC...
Пікірлер: 28
Gorgeous. Precise.
Outstanding video!!!!! Thank you, so simple now.
👍 thank you homie !
Thank you so much I really appreciate it!
Great videos ! I was looking for this videos for long time .. thank you so much !
@AZSolutions92
Жыл бұрын
No problem, glad this was informative for you 👍
Thank you so much 👏🏻👏🏻👏🏻
GREAT FREAKING VIDEO, BROTHER!
@AZSolutions92
2 жыл бұрын
Thanks man, Glad to here it was informative for you, stay tuned more content coming soon 👍
You sir are an ARTIST.
wild that its structurally solid with just tape
@AZSolutions92
7 ай бұрын
Yea man, the more you run the squeegee on the tape the better it adheres to the duct, you can also add some mesh tape then mastic for a more strong seal.
Grasias.
Donde compraste el palto del angulo yo llevo casi 2 años en este negocio y me gusta esta herramienta es muy practica
Hey Sheet metal worker here, curious, if you used the same standards for metal elbows, would the airflow improve? (I.E a full throat elbow) Using the miter rise formula to get a full throat elbow on that 15" wide duct, you'd have to cut the throat for that middle piece at approx 11.5 inches instead of 3 inches. though maybe that's just not practical?
Do a 45 next
How do you connect the transition 14x8 to 12x8 duct?
@alexanderrosales9175
6 ай бұрын
I just cut the corners longer and bend the S’s at a 45 degree and use 1inch bend it to the right size to 12x8 and voila just connect the duct together
You said staple, but I didn't see where they went. Isn't it required to be stapled?
@AZSolutions92
2 жыл бұрын
The staples are required to be on the closing flap of the duct board. When cutting an offset like in this video the the 2 tape tabs that I used to pressure duct together are by law from the duct construction handbook no staples are required, only foil tape that is code compliant may be used.
Does this work the same way if the 90 is on the shorter face of the duct?
@AZSolutions92
2 жыл бұрын
Yes, as long as you use a 22.5 degree template or speed square marked at 22.5 degrees.
@alexanderrosales9175
6 ай бұрын
You add 1 inch flange to have the pieces together with tapping screws or do only S’s and Drives ?
can this be done with sheet metal?
@AZSolutions92
Жыл бұрын
Yes, its the same with sheetmetal except you have to account for 1” on all sides to allow for the slip & drives to attach properly
Sir I am duct fitter you have vacancies tell me
You realize you could have taken the number 6 cutter and went around your lines and it would have made the one inch tab all the way around so when you connect it you dont have to fight to line it up you did that way harder than it had to be
Thank you so much I really appreciate it!