You know it's not working when the title says "100% working"

@bongogorillatag7025

9 ай бұрын

Fr😂

@neutron11.12

8 ай бұрын

Yeah. But it kinda worked, and use steam to work

@steep7189

8 ай бұрын

Если постараться то заработает, если его сделать на бензине или на спирту, я так делал только одноцилиндровый и двух тактный, с самодельной системой зажигания, топливо использовал спирт + масло

@Allmightygreat

6 ай бұрын

@@steep7189nice

@SandY___

5 ай бұрын

​@@steep7189shut up idiot

For anyone that wants to know, this isn’t a steam engine it’s a sterling engine. A steam engine has exhausts for the steam which builds up pressure in the cylinder. Sterling engines reuse the same air by heating, cooling and repeat.

@fishyerik

9 ай бұрын

It's not a sterling engine, it's not a complete model of any type of real heat engine, an heat engine needs as much cooling as heating. All the syringes in the video are just fed in parallel, or are supposed be, it's definitely faked. A sterling engine needs expansion and contraction, a cycle, not just being fed steam, that doesn't work.

@ichosolemanuel6048

9 ай бұрын

Def fake

@kellyoliver727

6 ай бұрын

Stirling*

@shakesmarley4754

6 ай бұрын

@fishyerik yes but if you could use compressed air and have it strong enough to move the pistons he could be onto something here right. Obviously this needs a better construction but this is a cool concept since we can use a trompe hammer to compress air and run this thing quicker. I’d have used more stable parts and actual pistons but it’s not out of the realm of possibility all is needed is enough air to move each piston?

@kcube4639

4 ай бұрын

@@fishyerik I'm not entirely sure but u maybe right , because the air or steam is expanding and therefore pushing the piston but I don't see how the fluid expands at the other end of the piston and pushing it backwards and there was no slide valve system like real steam engines. Please explain it to me if this is real

Wowooo hongera sans kwa ubunifu huu mzuri sans

Fake video but still a cool design. This can't work without intake/exhaust valves. There's no way you can just dump steam into a cylinder and expect it to exhaust against more steam constantly being admitted. It needs incoming steam to be cut off and the exhaust valve opened to atmosphere. Otherwise nothing will happen. You would also lose a lot of power with top dead center of the stroke so far away from the top of the cylinder. The goal is to remove as much used steam per stroke as possible. I like how you made the crankshaft! Pretty clever using motorcycle chain links and some all-thread. If you added provisions for valve actuation to the crankshaft, then you could actually control the steam admission and exhaust for each cylinder. Simple slide valves can be made easily with the parts you have. You could also get a smoother running engine if you offset the crank journals by 120 degrees like a real V6. More support for the center of the crank would also help you out as well. You can see it flexing in the video. 1 or 2 more bearings in between journals with proper support would minimize flex. I don't like being critical, but your design does have potential. I'm not sure what kind of glue you're using but if you do end up improving it like how I described then epoxy would be better. Good luck!

@manishsondarva0497

Жыл бұрын

Yes sir that's what I was also confused. Because see still it has so much friction. And yes 120° also good idea for crankshaft but he used only 90° two set and it can create more strech on shaft instead of 90° to each and every poles. And main and important what about exhaust. I don't understand this physics does it is fake video or what. I have found your comment intelligent so I also share my view to you.

@steganomaledoor3147

11 ай бұрын

I now get your intake/exhaust valve theory. You are right.

@ScreamingEngines18

10 ай бұрын

Actually I think he might have mislabeled the engine. This seems to me like many other sterling engine models people make. The way these work is by heating the air in the can which can expand into the cylinder and push the piston and than is reinserted into the can as exhaust and is reheated and re-expands into the cylinder. It’s a pretty cool engine I’ve been thinking about making one for study and entertainment purposes

@aviadfalah3085

8 ай бұрын

@@ScreamingEngines18still even in a sterlin engine there is a second piston to navigate the cold air back to the burner, which this model does not. But I’m sure going to copy and modify it myself. Awesome idea

Liked the idea of your crankshaft

o melhor motor que eu ja vi.

@kayros2894

5 ай бұрын

This engine not working

I ❤ hope you like the video. If you have an idea for a new video, please write it in the comments section. Thanks for watching.❤❤❤

@danielgoral258

Жыл бұрын

Blackburn

@DaljeetSingh-uh6nz

Жыл бұрын

Hey do you have this project

@DaljeetSingh-uh6nz

Жыл бұрын

Pls ley me now i will pay you

@hemanthjamisetti7863

10 ай бұрын

Hlo...I have some doubt on it can you clarify it ...pls...

@lemonindiallc7210

7 ай бұрын

Hey can i buy it

ایول داش خیلی منتظر پستت بودم

@skillmake

Жыл бұрын

از این به بعد بشتر هستم

Where is the exhaust unable to see

@oprekboy9693

Жыл бұрын

😂😂 very good question. That is not steam engine. Skill Make said steam because he added water into main tube. I think he did not understand why the pistons can move....🙏IMHO

@steganomaledoor3147

11 ай бұрын

No need for exhaust because there is an open fire. What do you want exhaust for?

@oprekboy9693

11 ай бұрын

@@steganomaledoor3147 for dispose of the steam/pressure that has been used to push the piston, so that the piston can return to its initial position. But it could be that the steam/pressure comes out through a hose connection, so you do need exhaust. Internal or external combution engine have the same principle.

@steganomaledoor3147

11 ай бұрын

@@oprekboy9693 Yeah, I guess you are right.

@williamfoster6172

11 ай бұрын

Each piston needs a waste-exhaust hole bored at the downstroke.

The red piece is called an air divider for fish tanks - if it helps you, click like❤

@user-vo5di5mp1x

2 ай бұрын

thank you very much 😊

What a nice skill. I love this idea so much and useful that's why I subbed u

@skillmake

Жыл бұрын

Thanks for watching

@georgefolk3134

9 ай бұрын

The engine won't work if you tried to make it with this design it has no timing for the power stroke meaning this will just push the pistons to the most furthest extension possible and the engine would just stay there

What is te red thing that you use two connect the hoses ?

Brilliant idea of using cycle chain using cam 😀

@MeldorKnight

11 ай бұрын

shut up

Wow! A steam engine that functions perfectly without any manner of valve gear!? So many convincing!!! Edit: Okay, sarcasm aside, the way you managed to fake this was pretty impressive in its own right. Did you use stop-motion animation or what?

Only one thing is to ask. Hope I will get my answer. Ok fine let's forget friction, drage, timing for something. But what about exhaust. See I don't know what the idea is used here or which physics is used here. Because see there is total 6 cylinder but they all are in two series, but it can get more powerful if they all are set at 90° to next to eachother. Still the exhaust stand there what about it. Because if it will refilleds the boiler than boiler will get blast or if it doesn't happen than the movement of postion will stuck. I like your design but still the arrangement of crank and exhaust I don't understand. Please make it clear if possible.

@kannaninsevagan3415

Жыл бұрын

Totally agree with you on all your concerns and improbabilities. Your idea to set at 90 deg to each other is also the traditional way, but he has only 2 set of inlets (Not even any outlets), so with 2 inlets, the system can only work as a 2 cylinder model. If 90 deg from each adjacent, then each cylinder will be 25% out of phase with the adjacent and the 2 inlet model will not work. He will need 6 tubes, making it an extremely complex and inefficient model. From that context, his idea to make it a 2 cylinder system (although in 3 subunits) may be better. Drag and friction are inevitable, so not sure how that can be overcome, I have used syringes for 40 years as a physican and I can testify about the friction in the plunger in the syringe. Also assuming that the copious amount of steam condensing lubricates the plunger, an exhaust is still needed, and a small hole in the body of the syringe at max outward position of the plunger might actually exhaust the cylinder, and drop the reistance substantially that the return stroke might be easier and the system more efficient, overall I dont think this model is real, but may be it is...

@ichosolemanuel6048

9 ай бұрын

Im not reading that kanninsevegan

Nice 👍🙂

خیلی. خفن بود !!واشر سر سیلندر پرایدم عوض میکنی اوستا

Good

good job

Can you advise of dimensions of all parts used? bearings, all-thread steel pipe, bike chain, etc, etc

@kayros2894

5 ай бұрын

Its not working

there is a mistake in the title, not 100% working just 100% fake

@serwanmohamad8402

2 ай бұрын

How do you know? Are you a engineer

@cornrecords

2 ай бұрын

@@serwanmohamad8402 Yes, I am, but it doesn't matter. A basic understanding of physics, taught in school, will allow you to understand that it's not supposed to work. If you don't believe, build the model yourself and see ;)

I proud of you my compatriot for doing such a thing 💗

can you tell what things were used in this thing?

Amazing 😍

@skillmake

Жыл бұрын

Thank you! Cheers!

@mdmosharofhossain12

Жыл бұрын

Wq 😊

You earned a sub

داداش ام اون سیم کلفته که به عنوان پیستون استفاده کردی چیه

Como faz essa válvula? Aonde consigo uma How does this valve work? Where can I get one

@neppoyeppo

Ай бұрын

São divisores de ar pra aquario

What is the name of that súper Glue 😯 i need it

items list ?

So does it work without exhaustion

Naysss

Perfect

Broo como se llama las llaves drogas por donde pasa el favor😮

Puede acelerar?😊

Люфты сумасшедшие на чëм-то таком коленвалоподобном.

Most genius and good work and God bless u😴

Como é o nome desse negócio vermelho?

👍👍👍👍👍👍👍👍

change the crankshaft arrangement and it will work like an actual v6 and it would be stronger

@goldenhero6204

7 ай бұрын

I was just gonna comment that

Rojas q digo esa donde se ponen las mangueras

Actually the system needs an exhaust, and I suspect this can be done with a small outlet in the cylinder part of the syringe, at max movement of the plunger. The three outlets on one side can be connected to an outlet tube and the water drained away from the system itself. This "small outlet" is not any different from the traditional exhaust outlet in the engine chamber. Exhausting the steam might actually drop the pressure inside the syringe significantly, the engine might perform more efficiently. Just a thought, not sure if feasible.

@steganomaledoor3147

11 ай бұрын

There is no need for an exhaust....remember, the exhaust is for the fumes to escape from a closed combustible engine. This one is running on an open fire system. Only if the fire was in an enclosure would we need an exhaust.

@MitPatel-yr3yt

11 ай бұрын

I’m pretty sure he’s talking about the steam from the boiling water

@steganomaledoor3147

11 ай бұрын

@@MitPatel-yr3yt Oh yes! I think so too....and he is right.

@Radioactiveiguess

10 ай бұрын

@@steganomaledoor3147dude no one is talking about the fire exhaust we mean the steam it is gonna build up pressure and explode

@steganomaledoor3147

10 ай бұрын

@@Radioactiveiguess Yes I agree.

Hi brother where are this part is available

Pretty sure he used that Vaseline to relieve some stress after making this video

❤❤❤❤

gostei !

Above the super.....

CAN IT BE USED WITH A DEODORANT?

@shakesmarley4754

6 ай бұрын

Don’t do this please you’ll blow yourself up bro

Podrían decirme cuál es el material a comprar, porque hay muchas cosas que aún no consigo para hacer el experimento

@luisfernandoguerreropedroz8928

2 ай бұрын

creo que la lata que uso es de aire comprimido, ademas de las jeringas y el tubo transparente, lo que aun no se que sea es la pieza roja del minuto 7:58

2:15

There is a leak of steam from al around the syringe pistons Guys take it easy this system gonna do nothing for real Exhaust would be necessary if the system was without leaking to decrease steam pressure but all around the syringe pistone we have leaking of steam This is my guess of course.... Also there is some regulator on valves that can control steam pressure

This will cycle once every 1000 years

Посмотрев это видео,я понял что такое двигателя внутреннего сгорания

Can you please tell me the all equipments name..... specially the red steam separating equipment..... please....

Pregunta como se llama la cosita esa donde conectó las mangerita

@Repanpanosx

10 ай бұрын

Distribuidor híbrido

👏🏻👏👏🏻👏👍👍

where did you buy the dc genorater

@mineland66

9 ай бұрын

Xd

Name of all part which is use when I make this project

@saideepsahu

9 ай бұрын

Yes please

ماهو السائل المستخدم

Bukhari pressure on both sides. How does he move?

This thing can change the fire into electricity i just needed to add a dynamo and boom am done

@ichosolemanuel6048

9 ай бұрын

Its fake but good luck

The vaseline one is relatable

my cat liked this video

consider using proper balancing

حلالت😎😎

esto no puede funcionar jamás, se necesita abrir escapes a las jeringas y unas válvulas que metan el aire en el momento exacto aparte, esa caldera es insuficiente para 6 "cilindros" de ese diametro y carrera

wrong firing order

sorry guys this was patched in the recent update

Those are pieces of a bicycle chain? Damn, I thought I was the only one in the entire world who thought of using those for the axle!!!!!

4:44

Hi

Hii

Oh yeah. A steam engine with no exhaust. That's totally a real thing. When it comes to physics, it's more like guidelines than laws. What a coincidence that at no point while the machine is 'running' can you see the ENTIRE machine. What's frustrating is that a couple strategically placed holes in those syringes and the thing might ACTUALLY work.

@OmarHARRAZE

6 ай бұрын

bro stop raging, he made s steam engine that works, there was just not enough pressure at the start for it to run on its own, so it needed a little puh

@Irish_Ronin

6 ай бұрын

I'm not so much raging as sarcastically mocking people dumb enough to think he built a working engine haha @@OmarHARRAZE

@thrguywiththecoins9726

6 ай бұрын

The syringes barely have enough sealing, so the gas escapes through the rubber part and the Vaseline. You can clearly see the inside of the tube clouding up from the steam. It works, even if its not planned as well as it should be.

battery was hidden

its fake, steam builds prespressure but there is no any exhaust

Просто тени кин и все

Vaseline melts plastic...

Sir apna no do iti me mere ko banana hai sir

@cadcamdraughtsman

3 ай бұрын

Bhai ham bhi ITI me bana rahe hai

@cadcamdraughtsman

3 ай бұрын

Apka contact do hoga to

Τι υγρο βαζεις στο μπουκάλι

@user-rz3dp5io6w

10 ай бұрын

Water

بلانه شو حط فاز،ين النيهه

no

Bs. 😂

bro anyone knows that this is fake AF .

Фууууууу

no flames Wrong,wrong,Wrong. can't anybody get it right.

Отработанный пар куда уходит ??? Пиздешь, провокация

@user-darbo

Ай бұрын

Более того нет системы парораспредиления, то есть пар то ещё может толкнуть поршень и выходить между поршнем и цилиндров но чтобы поршень пошёл назад подачу нужно перекрывать. Вобщем как говорит доктор Дъю, - у автора балестический гель головного мозга😂

Fake

Titanic model

@manualdomundo

Good

good job