How to level the deck | Troy-Bilt riding lawn mower
Тәжірибелік нұсқаулар және стиль
This is how you level the deck on your Troy-Bilt riding lawn mower. Always be sure to check your owner's manual for detailed instructions on how to adjust the deck on your riding lawn tractor. Order replacement parts or download a copy of your machine's operator's manual here: tblt.us/O.
Пікірлер: 54
Lightweight is good and what did I use it for it’s a lawnmower kzread.infoUgkxTPN04aT-Qdjr_KS3ql7ng8wnU3wwsCqk also recommend Yes it is lightweight so hence not as robust as our old one. But if you take care it does the job really well.
I've never adjusted my deck, now that I had to drop it to do the bearings I never realized how bad it was out of adjustment. Thanks.
thanks for the info the troybilt pony has been cutting the grass so low while on the highest position I was about to get rid if it!Hopefully this will raise the cutting so the grass doesnt look like its been shaved
My 42" Troy Bilt Mustang manual says ALWAYS level side to side before front/rear. And a reminder: Check tire pressure before any leveling.
Very important tip .......check your tire pressure A low tire that just needs air might be your issue
@davidvickers8425
3 жыл бұрын
Should be done first, before adjusting the deck and before each mowing
You're welcome. Glad we could help.
Ok so what do you do when tire pressures are correct and the adjustment screw is on the highest setting and the blade on that side is still .7 inches lower than the other side?
wow i be looking to fix the deck for so long thankyou
I have a troy-belt bronco 2011. Try raising the deck ,but still to low. Any other advice?
Alot easier than i thought it would be.
on mine, I found that part of the mechanism for raising and lowering the deck is a flange with an arced cutout in it where the top end of the rod that attaches to the deck is attached. In that arced cutout is a bolt below where the rod ends at a right angle and the jutting part goes through the arced hole. By moving that bolt up the slot to a higher position, I seem to get another inch of height. the bolt has a 3/4 hex on the inside of the cutout.
@anned.edelman2821
6 жыл бұрын
We use it!
Can you all show us how to do an alignment? I bought my Troy Bilt 46XP Super Bronco the other day and the front right wheel rotates differently than the one on the left.
I got mine serviced. I got it back the shoot side is to low. I have a bagger attached to the shoot. I tried adjusting it and it still won't work the shoot side is still to low. Maybe I'm doing something wrong. Do you have advice? Thank you.
Been having my troy Bilt since 2011 still working just started having issues with deck level I paid 1400 brand new they are much higher now
The hex bolt keeps loosening and the deck drops down why? It’s tightened over and over ??
My adjustment knob on the left side hanger doesn't turn either way. Even after loosening the 1/2 in hex bolt. What are we supposed to turn the knob with? Pliers will not tighten or loosen the adjustment knob
thank you
My mower is not cutting grass good. Leaves slot of uncut grass. Been this way since it was new. Any ideas people. I've got new blades . Good rpms. New belt.
I bought a second hand Troy built pony but need to adjust the height..what is the proper height adjustment for both sides since I don’t have a manual for it?
@mikerafone4736
3 жыл бұрын
getit on line
How the hell do you get your hand in there to take the measurement of the left side when taking the side-to-side measurements??
@mikerafone4736
3 жыл бұрын
you dont. get 4 pcs of 4x4 put them under the tires easy peazy
What is the point of those 2 small wheels in front of the deck? Are they supposed to be touching the ground or be in the air, doing nothing?
@williamwomack3153
17 күн бұрын
They float in the air mostly… they keep the blades from scalping uneven ground like a mound or hill… as you hit that the wheels will lift up the deck and not allow it to dig in
Leveling was no brainer, but my question is: is there a way to raise the deck? The highest setting is way too low and anything lower than that will mow dirt. I don't want to have to replace the blades every month.
@troybiltllc
8 жыл бұрын
+Nacho Reyes You can find instructions on how to raise and lower the cutting deck in your owner's manual. You can search for illustrated parts lists and owner’s manuals on troybilt.com using your 11-digit model number: www.tblt.us/O. We hope this helps!
@bottomdweller5
8 жыл бұрын
+Troy-Bilt Like I said, the highest position of the deck is too low. I actually drilled a new hole on both sides of the frame and was able to raise it and additional inch. Not much adjusting after that.
@googleuser1730
8 жыл бұрын
+Troy-Bilt How can you raise the deck past the highest setting. At 5 it is scalping the lawn at a height of only 3"
@hernaiztube
7 жыл бұрын
Nacho did you figure out a way? mine is way too low as well? Thanks
@bottomdweller5
7 жыл бұрын
The way I did it was to drill new holes on the sides of the deck. I was only able to raise it about an inch or so. You'll have to remove the deck to do it. This is where the back of the deck attaches to the body. Than relevel it. Let me know how it goes for you.
where's the pants go
@mikerafone4736
3 жыл бұрын
@@RYRHYMES can not be adj with tires on ground space under tires
Same problem, mowing down to the dirt! I never had this issue on my ancient John Deere, and the John Deere was much easier to adjust. Very POOR design! I'm tired of mowing into the dirt, my yard is anything BUT flat! Maybe it's time to invest in a newer John Deere, although this one is 10+ years and still going!
@mariconnors5670
3 жыл бұрын
I just realized the manual is not correct on how the height is adjusted . . . it actually goes in the same direction not opposite ones!
Well by god. Now I know. The nut on front
LuisAMelehnbpz