I got mine - thanks. Great trigger! Looks amazing and feels much better than stock. I installed it with the MCarbo Titanium Performance Striker Assembly and the gun feels so much lighter however even with blue loctite the screws keep coming loose after one range session. Will try to reinstall with loctite again and hopefully this time it works. Highly recommend!
@weaponri_4 ай бұрын
you guys could have marketed it as the T.I.T.S. trigger upgrade. Tyrants Improved Trigger System
@user-yf2bq7bv4v
4 ай бұрын
Love it, totally concur sir.
@tylernorman6240
3 ай бұрын
😂😂😂
@tyrantcnc
2 ай бұрын
It may have occurred to us at some point in development....
@warrenjsarah5 ай бұрын
got mine and installed it along with the extended slide release and looks great and works great, thanks so much !!
@derek38304 ай бұрын
If the slide release was placed in position FIRST and THEN the locking block inserted, it would have avoided the difficulty around the 10:30 mark -- because the locking block spring would have ended up over the left portion of the slide release providing the required tension. Hope that helps. In addition, a word about the pins. The pin going into the trigger housing has "3" small cutouts on if you look at it carefully. The locking block pin, however, has only "2" cutouts. Knowing this, it will make it easy when reassembling your Hellcat and identifying which pin goes where.
@tyrantcnc
2 ай бұрын
Thanks for the tip!
@warrenjsarah5 ай бұрын
mine will be delivered tuesday hopefully, cant wait to try it out
@realJohnLab3 ай бұрын
FYI.. if you are doing this on a Hellcat pro with a safety. On the left side of the rear housing is the as per the manual Safety Positioner , Safety Spring. Careful When removing the rear housing.
@tyrantcnc
2 ай бұрын
Great note!
@marcusraya4 ай бұрын
The video didn't show the reset comparison from stock , for me that is a factor do you have any videos showing the reset?
@timmyb8657Ай бұрын
You gotta make these in copper
@Sierra_18Ай бұрын
What size Allen key is that, I wasn’t given one by tyrant
@JOCERTIFIED7775 ай бұрын
Can you get it already assembled
@49ers49ers23 күн бұрын
When you install screw into new trigger should you apply blue locktite?
@tyrantcnc
19 күн бұрын
We advise it
@jordanrobinette129229 күн бұрын
So I get to the point right after getting the thick pin back in and my trigger is very tight and not easy to pull. Help!
@tyrantcnc
19 күн бұрын
Take your time, try to uninstall and reinstall
@BulletChronicles4 ай бұрын
So is the installation any different for California hellcat pro with magazines disconnect ??
@Darkside_Rob12
4 ай бұрын
I’m sure when u pull the slide back your gonna have to reach in the chamber and actuate the magazine disconnect lever to simulate having a mag in to get the trigger to move. I don’t have this trigger but this is how I’ve removed the slide in my other cali pistols.
@whiterhinooutdoors45723 ай бұрын
I bought this December haven’t shot it much till lately the factory trigger is shit I just put a holosun 407k on it and was excited to hit the range with I shot 5 magazines out it it has got a little better its probably had 600rounds ran threw it total but the trigger is shit I wanna like this gun but I hope this trigger is what makes me enjoy shooting this gun cause at the moment I don’t
@tyrantcnc
2 ай бұрын
Our trigger should help quite a bit with the feel, hope you enjoy it!
@dirttrackracingforlife71075 ай бұрын
When will orders start being fulfilled? I've been on back order for nearly 2 months?
@jeffmurphy9987
5 ай бұрын
I was going to order some but it took entirely to long to come to market. Then sold out quickly and no idea when more will be available. Personally I’m over it stock trigger is good enough anyway.
@dylanshepherd5904Ай бұрын
Would the process be different if the hellcat has a manual safety?
@CutTheKam
Ай бұрын
a little yes its in the comments
@aaronwilson47472 ай бұрын
When will you do a video for the Echelon?
@tyrantcnc
2 ай бұрын
Our Echelon install videos are up now!
@aaronwilson4747
2 ай бұрын
@@tyrantcnc for the upcoming Trigger? That, I do not see on the page.
Пікірлер: 30
I got mine - thanks. Great trigger! Looks amazing and feels much better than stock. I installed it with the MCarbo Titanium Performance Striker Assembly and the gun feels so much lighter however even with blue loctite the screws keep coming loose after one range session. Will try to reinstall with loctite again and hopefully this time it works. Highly recommend!
you guys could have marketed it as the T.I.T.S. trigger upgrade. Tyrants Improved Trigger System
@user-yf2bq7bv4v
4 ай бұрын
Love it, totally concur sir.
@tylernorman6240
3 ай бұрын
😂😂😂
@tyrantcnc
2 ай бұрын
It may have occurred to us at some point in development....
got mine and installed it along with the extended slide release and looks great and works great, thanks so much !!
If the slide release was placed in position FIRST and THEN the locking block inserted, it would have avoided the difficulty around the 10:30 mark -- because the locking block spring would have ended up over the left portion of the slide release providing the required tension. Hope that helps. In addition, a word about the pins. The pin going into the trigger housing has "3" small cutouts on if you look at it carefully. The locking block pin, however, has only "2" cutouts. Knowing this, it will make it easy when reassembling your Hellcat and identifying which pin goes where.
@tyrantcnc
2 ай бұрын
Thanks for the tip!
mine will be delivered tuesday hopefully, cant wait to try it out
FYI.. if you are doing this on a Hellcat pro with a safety. On the left side of the rear housing is the as per the manual Safety Positioner , Safety Spring. Careful When removing the rear housing.
@tyrantcnc
2 ай бұрын
Great note!
The video didn't show the reset comparison from stock , for me that is a factor do you have any videos showing the reset?
You gotta make these in copper
What size Allen key is that, I wasn’t given one by tyrant
Can you get it already assembled
When you install screw into new trigger should you apply blue locktite?
@tyrantcnc
19 күн бұрын
We advise it
So I get to the point right after getting the thick pin back in and my trigger is very tight and not easy to pull. Help!
@tyrantcnc
19 күн бұрын
Take your time, try to uninstall and reinstall
So is the installation any different for California hellcat pro with magazines disconnect ??
@Darkside_Rob12
4 ай бұрын
I’m sure when u pull the slide back your gonna have to reach in the chamber and actuate the magazine disconnect lever to simulate having a mag in to get the trigger to move. I don’t have this trigger but this is how I’ve removed the slide in my other cali pistols.
I bought this December haven’t shot it much till lately the factory trigger is shit I just put a holosun 407k on it and was excited to hit the range with I shot 5 magazines out it it has got a little better its probably had 600rounds ran threw it total but the trigger is shit I wanna like this gun but I hope this trigger is what makes me enjoy shooting this gun cause at the moment I don’t
@tyrantcnc
2 ай бұрын
Our trigger should help quite a bit with the feel, hope you enjoy it!
When will orders start being fulfilled? I've been on back order for nearly 2 months?
@jeffmurphy9987
5 ай бұрын
I was going to order some but it took entirely to long to come to market. Then sold out quickly and no idea when more will be available. Personally I’m over it stock trigger is good enough anyway.
Would the process be different if the hellcat has a manual safety?
@CutTheKam
Ай бұрын
a little yes its in the comments
When will you do a video for the Echelon?
@tyrantcnc
2 ай бұрын
Our Echelon install videos are up now!
@aaronwilson4747
2 ай бұрын
@@tyrantcnc for the upcoming Trigger? That, I do not see on the page.