1:45 "Gently smack on the spindle" *BANG BANG BANG*

You should always torque suspension parts at curb height. You can use a pole jack so lift the control arm up it doesn’t necessarily have to be sitting on wheel but the suspension should not be hanging. It will mess of the ball joint prematurely. Great video

Good work but you really need to pack the bearing properly. You can’t roll it in grease you have to force it in through the bottom until it squeezes out the top

@docbrown303

3 жыл бұрын

i was gonna say the same thing, bearing shot after 1 year im sure.

@tommywilliams1402

Жыл бұрын

😂

Great job and I like the camera angles! Thank you.

Really good video and editing. Forgot one part though, the turn radius will be reduced without this step. Using a die grinder with a cutoff wheel, remove approximately ¼” from the front lip of the lower control arm from the previous marked spot around the front radius of the lower control arm in front of the ball joint. This will allow clearance for installation of the new lift spindle. Increased turn radius for large tires.

@cameronadams1952

2 жыл бұрын

Hopefully you see this. But I recently tried to do a spindle lift on my 05 ranger edge and the turning radius is still like a bus even when we trimmed it. Hopefully you have some tips or know what we did wrong.

@cameronadams1952

2 жыл бұрын

Also after trimming the lower we had to jack it up to line the upper ball joint and when we lowered it it all relied on the upper ball joint idk how I felt about that

@Wes61

2 жыл бұрын

@@cameronadams1952 I ended up removing the entire flat lip part around the ball joint on the LCA everywhere the spindle rubbed. My ranger doesn't turn terribly but it did get a slightly reduced turn radius. I have a spindle and spring lift, with extended upper control arms and upgraded camber bolts. The extended UCA helped with alignment/steering issues but it smacks the frame. The best advice I could give is just make sure the spindle does not rub the flat part of the lower control arm.

@marcusglover9639

Жыл бұрын

​@Wes where did you get your extended upper control arms and camber bolts?

Nicely done, we'll spoken, great knowledge and know how. Thank you for you time and good video

This guy knows his stuff! Easy Peasy! Easy as 123!

Thanks for this video. I learned I will be taking my Ranger to a shop to have them do it! This looks outside my skill and confidence level.

@321ethan

2 ай бұрын

how much did it cost?

Excellent video.

Dang. I want this guy to my spindle lift kit! Lol

Great video

good job great video

Great video..

I just got these spindles and they send you china bearings so I got new koyo bearings LM12749

nice job

What all else do I need woth the spindle lift? New coil springs? And all that?

Very good job 👏🏾 but I need the truck all done please 😉

Awesome

Did you make those cement pads yourself ?

I'm trying to find those wheels for my ranger. Any info on them?

What's the average cost to do this? Thinking about doing it to my ranger.

Don't you need longer coil springs after installing this spindols?

Thanks for the video! I would like to ask if you would need to get an aftermarket upper control arm with this kit and where did you get it?

@nickjames9542

2 жыл бұрын

Looks like he running stocks my spindles jus came today I'ma see what happens wit stock an I got coil spacers

@nickjames9542

2 жыл бұрын

UPDATE my 98 ranger 2 inch coil spacer an 4 inch spindle lift with 3 inch blocks an 2 inch lift shackles stupid lifted needs bigger tires than 31s now for sure

@nickjames9542

2 жыл бұрын

Does not need control arms jus cam bolts

The link in the description is dead, anyone know what kit he used?

Will you need an alignment after due to the new angles of the joints and tie rod

@christopherw8654

4 жыл бұрын

Jared Cleary yes

Question the upper ball joint the hole is to small for the ball joint to fit how can you fix it?

Don't you need longer shocks and springs in the front? I have a 98 Ford ranger myself so I was excited when I saw this video but my dad told me I would need longer shocks or I'll be stressing out my truck. And I know I can lift up the back pretty easily with just blocks and u-bolts.

@memoaa7467

5 жыл бұрын

no, you will not need longer shocks. The only thing that Lift spindles do is changing the center of the where the tires are. you can use same shocks and springs.

@christopherw8654

4 жыл бұрын

If anything you would need longer shocks in the rear. But it’s not necessary. I would recommend changing the shocks anyways however cause those ranger do get a lot of mile.

you hVe any pictures of the truck if it lifted

Do I need to replace anything else ? Longer brake lines ? This will work for a 2wd ?

@aquaticamc6818

4 жыл бұрын

It works on any model I got a 4 inch spindle lift, I have a 3.0 v6 2wd and it's amazing, the total lift was about 4.5 inches actually

@totallypitted3447

4 жыл бұрын

Ethan, did you have to grind down bump stops on A arms to get full turning radius? Or have to grind on the spindle itself?

@totallypitted3447

4 жыл бұрын

@@aquaticamc6818 Ethan, did you have to grind down bump stops on A arms to get full turning radius? Or have to grind on the spindle itself? Did you lose any turning radius?

@aquaticamc6818

4 жыл бұрын

@@totallypitted3447 just a little on the drop arms and I had to remove my mudflaps because I have 33 12.50s and I use 2 inch spacers so I don't rub anywhere

@totallypitted3447

4 жыл бұрын

@@aquaticamc6818 Rad! Thx for the quick response! Too Cool! Bout to update my 05 and I wanna get it right. Did you feel a power drop with 33's? Thinkin imma top out at 31's to keep it somewhat of a daily driver. Almost 180k on the motor, tryin to keep some of the load down.

U got a shop?

Can this on my 87 ford ranger 2.0l

Is a spindle lift only for a 2WD car? I have a 2011 ranger 4WD, is cranking the torsion bars the easiest way to lift the front end?

@sp3_outdoors

2 жыл бұрын

easiest way to get 2 inches higher. get new keys and rent a tool from auto zone. 4wd spindle lift is not possible.

We replaced the spindles on my 05 ranger edge but my AA arm seems to not be matching up? Is there a trick or do we need to replace the A arm?

@curacaoz2875

3 жыл бұрын

Grind it

*GET CAMBER BOLTS!* or you will have some silly camber. Just install this lift over the weekend. Seriously get them and install them during the process not after its all done. Don't make my mistake.

tried this but the new spindle rubs way too much i won’t be able to turn idk why it doesn’t fit

Hello brother how much is it lift 12 inch the cheapest for ford ?

Do you need spring spacers too??

@itz_ypara1233

11 ай бұрын

Yes or u can get the bigger shocks

How much does this cost to pay a shop to do this? Ima get a 4" spindle lift with shackles in back

@itz_ypara1233

11 ай бұрын

U still need it done or have u done it? It’s pretty easy once u get the hang of it

Is that all it need to lift it up higher ? 2"? 3"? how high it gets?

@reaganriddle1583

10 ай бұрын

about 3-3.5in

Did these make your turn radius shorter , I just install one side on mine and the hit the sides of the lower control arm and while it's up off the ground with no weight on it the back side of the spindle is right up against the frame and you cant turn it at all , I replaced everything brand new. I got these off ebay and they look just like yours with the f150 spindles and outer bearing, I put a jack under it and it moved away from the frame but it still hits on the lower lip on the side of the control arm, Did you have any problems with yours and did you have to grind some of that lip away ?

why am I having trouble watching this video for some reason? It just keeps buffering and all the other KZread videos I watch I don't have this problem why is that??

✨ G E N T L Y S M A C K O N T H I S ✨

Ey shows the job done please!

What size shocks?

@itz_ypara1233

11 ай бұрын

Stocjs

I think your brake pad fell out

Axle nut should be torqued to15-20

why aren't my upper control arm ball joints matching up? everything else does besides the upper control arm ball joints

Couple ugga duggas call it good.