Ive been working with wood for 50 years. The hardest thing ive ever done is installing slides on new cabinet ( no previous slide with markings giving me a good idea where new slide goes!). I could build you a fighter jet from scrap lumber, just don't ask for slides.

You just saved my life right now :-D Couldn t been able to find any good manual from manufacturer :-) Thanks !

@thelondoncraftsmanworkshop

2 жыл бұрын

Great to hear, hope you subscribe 👍👍

Thank you so much for this tutorial. It's perfect! 👍

Hi Ryan Thanks for this video, just a couple of things, 1. The middle of the carcass slide is 22mm to centre plus an extra 20mm this makes 42mm and not the 44 that you draw the line at. 2. Why is it preferable to measure the slider holes rather than sit the slider on the drawer/ carcass and use it as a template? 3. On the carcass slide if you use just the holes that are in the 3 cut out portions and not the fixed holes, then if your drawer is slightly smaller in width than it should be, those cut outs allow the slider to come away from the side of the carcass and take up the additional gap. 4. I see you fit the sliders flush to the front and sometimes I see them set back by about 5mm is this down to personal preference or is there reason? Cheers for the video...

Nice one, this vid answered lots of questions, thank you. love your channel

@thelondoncraftsmanworkshop

3 жыл бұрын

Thank you glad your enjoying and its helping!

Great video, very informative. Thanks 🙂

@thelondoncraftsmanworkshop

4 жыл бұрын

You are welcome 😁

@thelondoncraftsmanworkshop

4 жыл бұрын

I'm glad its helped 😁

Cheers mate 🍻

@thelondoncraftsmanworkshop

4 жыл бұрын

No problems maty

So helpful thanks 🙏☺

@thelondoncraftsmanworkshop

4 ай бұрын

Thank you... I'm glad 👍☺️

Thank you so much. wow great video, very informative and thorough. You have covered everything thanks.

@thelondoncraftsmanworkshop

4 жыл бұрын

You are welcome, be sure to share it on your social media etc for me. Thanks Ryan

what product are you using for the actual draw? 18mm MDF?

@thelondoncraftsmanworkshop

4 жыл бұрын

Hi yes

I bought some runners online that are push to open. My problem is that once the drawer face goes on the drawer, I cannot open the runner. What am I doing wrong? Never ever had this problem with full extension runners before.

@thelondoncraftsmanworkshop

4 жыл бұрын

Hi sorry I've only just seen this message. Make sure the wide part of the 2 part runner is flush with the carcass when fixing. Once you clip the small part in it should overhang the carcass by 3 or 4 mm to allow for the push

@petermiles55

4 жыл бұрын

@@thelondoncraftsmanworkshop Thanks for your reply. I had to order soft close runners which actually work. there is no way that push to open runners work with a drawer face that sits over the drawer carcass.

i posted a question on your hinge video - should have watched this - 4years old - is this still your goto runners

@thelondoncraftsmanworkshop

3 ай бұрын

Haha its an old one 😊 Yep I still use these, they work really well for us 👍😁

@etafws

3 ай бұрын

thanks good to know - as mentioned posted on UKWORKSHOP - 👍👍👍@@thelondoncraftsmanworkshop

20+22=42 not 44

I was always told a carcass was a dead animal 😂

@thelondoncraftsmanworkshop

2 жыл бұрын

Haha your right

Bro you didn't even put the draw in 🙄🙄🙄

I bought GTV push to open and it is written that there is 5mm gap between front and carcas side, but do I need to montage them same as you flush straight to the front? Also I'm afraid of your screws, I'm amateur and I use 3,5x17 mm.