How to Wire a Double Duplex Outlet - DIY (OFFICIAL VIDEO) kzread.info/dash/bejne/gZlo19OMicW7YLQ.html How to Wire an Outlet Off a Switch - DIY - (OFFICIAL VIDEO) kzread.info/dash/bejne/naqqydSPcZexfdo.html

In my area and told at numerous IAEI continuing education classes that you should never run type NM-B ( Romex is a brand name ) in conduit. Most inspectors will allow NM-B cable in a say 3 to 6' long piece of conduit to sleeve cable down a basement wall to protect cable.

Like how you attached the first box over the original. This is exactly what I'm looking to do in my garage! Building out my work bench this fall, and this is one of the next steps.

@DIYHomesteadProjectsDIYHP10

Жыл бұрын

Thanks Riley, I wish you the best with your project!

Fantastic video. Saved me a ton of money. Keep them coming. Thumbs Up!

@DIYHomesteadProjectsDIYHP10

2 жыл бұрын

Thanks, will do! 👍

Extremely helpful and interesting to see your wisdom!

@DIYHomesteadProjectsDIYHP10

Жыл бұрын

Glad it was helpful. Thanks for stopping by.

Very helpful and easy to understand!! Thanks for sharing

@DIYHomesteadProjectsDIYHP10

Жыл бұрын

You're very welcome!

Nice, clear ,and detailed video 💯

@DIYHomesteadProjectsDIYHP10

2 жыл бұрын

Appreciate it!

Great video sir! Thanks for sharing. This is exactly what I need to do!

@DIYHomesteadProjectsDIYHP10

Жыл бұрын

You’re welcome Russ. I wish you the best with your project!

Looks nice, you have a great work bench area there Bruce. Merry Christmas and a happy healthy new year to you.🎄🎅☃️❄ and your wife

@DIYHomesteadProjectsDIYHP10

3 жыл бұрын

Thank you and same to you and yours. 😀

Looks good! You twist those wires together nicely! I like the animated video at the close, too. ;)

@DIYHomesteadProjectsDIYHP10

3 жыл бұрын

Thank you very much!

Great video, especially showing how to wire it!

@DIYHomesteadProjectsDIYHP10

9 ай бұрын

Glad it was helpful!

Thank for this video. My son's and I are going to add some boxes like you did in our garage and you explained it so well.

@DIYHomesteadProjectsDIYHP10

2 жыл бұрын

Awesome! Thank you! Have fun with your project.

i needed this video

@DIYHomesteadProjectsDIYHP10

2 жыл бұрын

I hope it helped you out and thanks for watching! 👍

great video, thanks

@DIYHomesteadProjectsDIYHP10

Жыл бұрын

You’re welcome. Thanks for stopping by.

I’m in the process of doing exactly this- unsure if I want to go thru the studs or exterior like yours? Great informative video.

@DIYHomesteadProjectsDIYHP10

2 жыл бұрын

Good luck with your project!

Drawing blood on a project is just good luck! Great explanation. Learned a lot. Thank you Thank you!!!!

@DIYHomesteadProjectsDIYHP10

2 жыл бұрын

Thank you Wage, glad to hear it helped you out! Thanks for watching!

how did you ground the box initiallY?

Question: at 10:40, what kind of screws did you use to attach the cover to the box? I’ve got a few boxes in my garage with missing screws, some covers are held on with only one screw. I’d like to get new screws and put them in but not sure what kind to get. Thx

@DIYHomesteadProjectsDIYHP10

2 жыл бұрын

I just used the screws that came with the box cover. I would think any hardware store will have replacement screws for metal box lids. Sorry but I don't know the size and thread count.

Nice job and it's interesting to see the difference in wiring codes. Here in the UK regulations are that any bare copper earth conductors must have green and yellow sleeving on them in back boxes and so on. Also when joining wires screw block connectors are used or, as it seems more commonly now, Wago connectors which use little levers to clamp the wires in place.

@DIYHomesteadProjectsDIYHP10

3 жыл бұрын

Thank you

Where did u start the conduit?? The first box is surface mounted & then bare wire. I see the ends are in conduit. Do you need to have conduit from the source or can the wire be surface mounted & stapled(etc) to the drywall? Thanks for posting this!!

@DIYHomesteadProjectsDIYHP10

2 жыл бұрын

I started the conduit at the first box and it extends to the next box. I didn't want any exposed wire along the wall. I don't believe you should staple the wire to the outside of the sheet rock.

Awesome I appreciate that very much it helped tremendously keep up the good work brother.

@DIYHomesteadProjectsDIYHP10

3 жыл бұрын

Thanks Billy, I appreciate it!

Does it matter what material the screw is that needs to mount the boxes to the stud?

@DIYHomesteadProjectsDIYHP10

2 жыл бұрын

Not that I'm aware of

I'm a new subscriber

@DIYHomesteadProjectsDIYHP10

3 жыл бұрын

Welcome Timothy 👍

1/2” conduit is big enough fill for 12/2 Romex?

@doctordhd

Жыл бұрын

Good question. We need an answer for this.

Wanting to add 4 boxes of four like you have. Do I need to run back to circuit box or can I connect to existing gcfi?

@DIYHomesteadProjectsDIYHP10

Жыл бұрын

I really can't tell you how to set yours up but mine do not go directly back to the main breaker box. Mine are all down line off the gfci outlet.

@terrortotriumph180

Жыл бұрын

@@DIYHomesteadProjectsDIYHP10 can u share what you used: what type of wire, electric box used to hold both outlets, etc?

@DIYHomesteadProjectsDIYHP10

Жыл бұрын

I have links to everything I used listed in the video description.

Curious why you didn't describe how you ran the conduit??

What size conduit is that?

@DIYHomesteadProjectsDIYHP10

2 жыл бұрын

1/2"

Great job all by standar code .. be carefull whit over load the braker that suply power to you sircuit .. 👍👍👍

@DIYHomesteadProjectsDIYHP10

2 жыл бұрын

Thanks for the tip

As a life long electrician NEVER waste your money on a 20 amp receptacle unless a window air conditioner requires it. A 15 amp duplex receptacle is perfectly legal to install on a 20 amp Arc Fault circuit breaker ( also provides GFCI protection ). The insides of all 15 & 20 amp duplex receptacles are identical. I've been in my house over 45 years and NEVER had to use a 20 amp male plug. ran 3/4" EMT conduit in my garage for additional receptacles.

How do u know what circuit ur on

@DIYHomesteadProjectsDIYHP10

Жыл бұрын

Mine are labeled in the main breaker box. You can flip the breaker you think it is and then go test the outlet to see if you have the correct one.

Do I need electrical permit or can I just do without it?

@DIYHomesteadProjectsDIYHP10

3 жыл бұрын

I recommend you check with your local building department. The rules and requirements can vary depending on where you live.

@TheOriginalVersatile

3 жыл бұрын

@@DIYHomesteadProjectsDIYHP10 OK. Curious did you get one or you just did the work without it?

@DIYHomesteadProjectsDIYHP10

3 жыл бұрын

A permit is not required for this where I live. I did the work without it.

The first box you put in is wrong. You can not cover a box with a box, big code violation. It should have been removed or an extension box put over it.

@chesslover8829

3 жыл бұрын

In addition to your comment, I would have used THHN wire, instead of Romex, and I would have taped the wire nut connections.

@aurvaroy6670

Жыл бұрын

Who cares? It's not like he's moving out of his house and the new owner requested an electrical inspection for whatever reason.

you cld have cut down the connections by daisy chaining the outlets together leaving just one set of wires from coverplate to tie into the other two loads leaving just 3 wire nuts with three conductors under 2 and a copper crimp or larger wire nut for the grounds or the special green pass thru wirenut with just 3 conductors sill for the ground. i do add wire extensions too when i wire up boxes like this example i wld have added one extra nmb cable from the feed box not 2.

Not legal to have splices that are no readily accessable going by the NEC. Two possible ways of what you should have done. 1) installed a 1/2" chase nipple and made splices inside of new 1900 box or 2) cut an opening as large as possible then install & glue a tubing to protect wires and make splices in old existing wall box. Have to use 6/32 screws to secure new box to wall box.

I'm not an electrician, but I think you did a very professional looking job. I did something similar in my garage, but I used THHN wires in the emt, not Romex. The use of 15 amp duplex receptacles on a 20 amp circuit with 12 gauge wire is commonly done and is code compliant, as long as it is a duplex receptacle and not a single. You cannot use a 20 amp receptacle on a 15 amp circuit. The reason why I mentioned this is that it sounded like you thought that it was not correct.

@DIYHomesteadProjectsDIYHP10

3 жыл бұрын

Thanks for the comment Ted, I appreciate it! I am aware of the 20 amp receptacle on a 15 amp circuit. I mentioned it in the video because I get a lot of comments with people telling me it's not ok. I considered using THHN but the Romex was quite a bit cheaper. That's why I decided to use it instead of the THHN.

@ronbelnap8370

2 жыл бұрын

Many locations do not permit Romex in a conduit. Heat dissipation issues.

@JohnThomas-lq5qp

Жыл бұрын

You can use a 15 amp single receptacle on a 20 amp breaker and only #14 copper wire IF it's for motor load that might trip a 15 amp breaker due to high inrush ( a second or two of locked rotor Amps ). Good example would be an air compressor or window air conditioner.

your gunna love wago lever nuts

@DIYHomesteadProjectsDIYHP10

3 жыл бұрын

Yes, they are nice

I RECOMMEND USING GLOVES WHEN WORKING WITH THIS TYPE OF INSTALLATION.

The buried splice in the old box is a Code violation.

Nice clean job! But It’s a code violation to run sheathed wire through conduit

@DIYHomesteadProjectsDIYHP10

2 жыл бұрын

Thanks Peter

@haunthunterify

2 жыл бұрын

So what are you supposed to use? It will be beneficial if you say what to do instead of just NOT what to do.

@briantinsley7864

2 жыл бұрын

It’s up to local jurisdiction, but NEC allows EMT to be used to protect romex. I’ve heard fire hazard, but run some 12-2 through an insulated south facing wall and fire up a toaster oven or hair dryer. Which romex gets hotter. Where’s the fire inside the EMT? How about using stranded THHN ? Are all your connections solid, with no strands sticking out causing a fire hazard ? I like the spirit of the code, but it’s not bulletproof, and his guy makes tight connections, and isn’t hiding any work. Even the box on the box can easily be opened for troubleshooting. Yes it could fail inspection on a bad day, but I’ve seen licensed electricians run multi-wire branch circuits using 12-3, on two fuses, 15 and 20 amp, branches extended with 14 ga, and the breakers not tied together. It’s not code, but passed inspection. Wire as safely as you can, but code and inspections didn’t guarantee my safety. DOnt get me started on the multi-wire branch to DW and disposal, that got a nail through the excess slack. This was all professionally done. This guys work is better than what I saw

They make an extension 4x4 box that meets code, your hack does not. Red wire nuts would have cut your splices in have.

@MrMtm13

2 жыл бұрын

All the extension boxes I looked for, don’t have a screw hole to ground the box/extender. All metal boxes should be grounded, right? Could you link the code compliant box if possible please? Thanks

Why would you bring two feed wires in your new box you only needed one so you would have not had to splice 2 wires instead of 3

@aurvaroy6670

Жыл бұрын

True but he didn't wanna buy larger wire nuts. At least, that's what he said in this video

Two GFI’s on one circuit will not provide protection. ONLY the first outlet in the circuit should be GFI and all downstream outlets will be protected. And only a total of up to six outlets per circuit.

@wizard3z868

3 жыл бұрын

ya not to mention 2 gfci on one circuit fight with each other and one or both trip or even cause breaker to trip too. fun times when home owners dont realize what a gfci breaker is and just add gfci outlet next to a sink or outside 😱🤦‍♀️🤦‍♀️

@thomasmarable6818

3 жыл бұрын

That depends on how they are wired. Gfci dont fight each other. You can put all gfci in if you want.

@dajur1

3 жыл бұрын

@@thomasmarable6818 Sure, you can, but it's a terrible idea and completely unnecessary. GFCI's don't "fight" with each other, but when one trips, sometimes they all trip and if there are a bunch of them, you have to reset them in order. Even if only one trips, you may have to hunt it down to find the right one.

@thomasmarable6818

2 жыл бұрын

@@dajur1 depends on how you wire them. But it get expensive to put all gfci in

My garage has outlets... 15 amps that are on the same circuit as the outlet in the damn laundry room on the second floor. Same circuit used by the washing machine...what the hell were they thinking.

@DIYHomesteadProjectsDIYHP10

3 жыл бұрын

Good question

@misterl2875

3 жыл бұрын

The laundry room should be independent AND the washer and drier should be on separate linked breakers.

Or you could have saved yourself a little time and used mc cable

Code violations all over the place.

Wrong box connecters, and so much more…. do not do this ! not up to code