Interesting. I took my 2005 Civic Si EP3 to my shop couple days ago. Was told that front suspension needs to be pulled to access clutch. I was @ around 10% clutch left. I'm getting an Exedy stage 1. Should get it back next week. Can't wait.

@Enkor528

Жыл бұрын

i'm in the same boat as you! also gon' roll stage 1's/

Great video bro! Just wanted to say thanks for the clutch bypass by bridging the leads of the connector! Been looking for this info and luckily stumbled across it in your video.

Take such and such “ewt”. Omg this makes me miss my Canadian friends 🤣😭😭😭 Thank you for posting this!

You never showed where those bolts went for the Mount, but I believe I found it. Im doing mine as we speak

Was it hard to remove the starter without removing the intake manifold?

Thanks for the info, we are inspired to make a similar video as we need to do this job also.

Hey how long until the turbo pulls?

You can realign the axle if the U joint seperates at the axle cup.Pretty easy.Just make sure the boot doesnt get torn.

Thank you so much I have to do this to my rsx this weekend now I have a way better idea this should be a breeze

@jdmodsgarage

5 жыл бұрын

Yeah is really not that bad just take your time and torque the bolts properly and you'll be fine!

Great job

Did you need to bleed it up after??

did you have to remove the starter?

Any videos on how to replace the Slave cylinder or master cylinder on the ep3, drive one today clutch felt spongey

@screwdajuice

3 жыл бұрын

Remove your intake housing, unclip/unbolt the clutch line running above the transmission, remove the two bolts holding the slave cylinder. Undo the line going to the slave cylinder (10 mm) and replace it.

Quick question, when pulling the transmission off do any of the dowel pins fall out or come off either from the bell housing side or the engine block side?

@jdmodsgarage

4 жыл бұрын

Nah they kinda just stick to where they are. They are press fit for sure

Hi mate, did you have trouble with the clutch travel with the competition clutch? I have seen forums of adding a washer to the clutch release fork ball joint to allow for a higher biting point on the clutch. I have installed 2 of these and the bite point is to close to the floor, even when the rod is adjusted to maximum travel

@jameswiedman8379

Жыл бұрын

I run a stage 2 comp clutch and it just failed. Was always squishy as hell from the install then on. And like you said had to be pressed too far to get it to disengage. Now mine won't disengage. Time to remove and replace.

2.4 on your si. Damn. I wanna do that to mine. I just don't know how

Hello I was wondering if you can tell me how to fix my left head light, on start it doesn't turn on I have to drive it a while to start it has gotten progressively worse. I drive an 02 rsx base silver

Can you show whats the right throw or travel on the clutch pedal.

@inventor719

5 жыл бұрын

There is a range that works probably based on your preference

@bhadz100

5 жыл бұрын

inventor719 is this your burner account?lol thanks

@jdmodsgarage

5 жыл бұрын

Sorry wrong account lol

@reza_dc2

5 ай бұрын

@@inventor719 How do you adjust it ?

Dam man, where the hell do you find a phone book these days?

That wood friend is PLANK from ed,Eddie,eddy! Ha!

Not step by step so many steps missed that I’m clearly finding out doing mine

You need to seriously invest in some high lumen LED work lights

Clearly no ten min job 😢😢😂

That wasnt that good of a pull ):

Yea change the name of the video of your not gonna show how to put the clutch on thanks for wasting my time

@xardenas2636

3 жыл бұрын

It’s not that hard to google torque specs.

Why didn't you do it from the top? Just curious

@danielstephens4420

4 ай бұрын

Not enough room