Fitting a serpentine belt - Civic Type R EP3
Автокөліктер мен көлік құралдары
A quick guide mon how to go about changing your serpentine belt on an EP3 Civic Type R with Aircon.
I left any mistakes and issues I had on purpose just to show you how to fix them if yhou make similar errors.
Пікірлер: 43
Thanks for the tip on using the 14mm and the torque wrench. This is going to make this job way easier.
@big_gooch1601
7 жыл бұрын
Corey Garcia no problem just go easy when applying pressure and it will work fine. thanks for taking the to watch the video
hi, i know this is a few years old now but just wanted to say thanks for this - not including getting jacked up & wheel off i think i had the belt changed in about 2 minutes thanks to watching this video.
@big_gooch1601
3 жыл бұрын
That's cool, you're welcome bro.
Awww bollocks!! I forgot to loop it round the a/c pulley... hehehe made me laugh :D
Thanks for making and sharing that video. I would have most likely over-torqued that top idler pully bolt and broken the brittle cast bracket, so many thanks for that warning. 16 lb.ft or approx 22 N.m
well done sir. very good and informative video
Great video and Thank you for saving me a lot of time :-) I watched it a twice and did belt, idler and tensioner pulley in about 30 minutes. 10 of those minutes was wasted trying to get the little nut to thread on to the tensioner pulley bolt. I didn't even realize there was a nut until I tried to remount the new pulley. Lucky for me it landed a only a few inches below and was easy to find.
@big_gooch1601
6 жыл бұрын
Unicorn Tribe thanks for watching 😎
Spot on, this helped big time
Very good demonstration , thanks!
Great vid, helped me with some tips and pointers that would have made my idler change mildly annoying! Thank you
@big_gooch1601
7 жыл бұрын
Byron Viljoen many thanks. I'm glad it helped you out. did you use the tip about the open ended spanner and wrench?
@ek4turbo
7 жыл бұрын
I did indeed, made it a whole lot easier than I had thought it was going to be. Also the over tightening would have happened if not for the vid :)
Thanks this helped loads!
very helpful video, thanks m8.
@big_gooch1601
7 жыл бұрын
glad you found it useful. Hopefully you don't make the same mistakes I did
Thanks for the tip to ease the tensioner, you legend!
Thank you!
Thanks for your time mate
@big_gooch1601
3 жыл бұрын
You're most welcome, I'll be re launching the channel soon
Probably not going to be able to set the belt on the lowest pulleys without getting access underneath! Guess I'll be buying a jack and stand, it's about time anyways. Thanks for video!
cheers mate good vid
@big_gooch1601
6 жыл бұрын
Thanks Mike hope you found it helpful
Thank you 👊
good job thank you so much .....
My belt is slightly riding the outer edge of the idler pulley. K20a type r jdm. I think the guy who swapped it was in a rush, back to shop
Thank you sir
Threading is a bit easier if you remove the headlight too, mate. Great vid though.
Seems like the new belt takes some damage during the install
Nice video mate! What's the risk if these snap then? Mine is looking worn and starting to squeak a bit so I need to get it done ASAP
@big_gooch1601
6 жыл бұрын
No risk to your engine pal although I don't think you would be able to drive it far hopefully you would have enough battery charge for it to get you home
@shiraazmaqsood
6 жыл бұрын
Big_Gooch cheers for the timely reply, that's good to know, I'll get it sorted thanks to this vid. Thanks man
Should of done a before and after so we can here the difference. Nice vid
@big_gooch1601
6 жыл бұрын
+benjamin2kbl Thank brother. It certainly made a difference. I miss that car badly
@BigFurryCat
4 жыл бұрын
Buy another you fool ;)
Hey mate! Does the engine have to be in tdc to change this belt? Thanks in advance
@big_gooch1601
3 жыл бұрын
No pal absolutely not, it's purely for the ancillaries.
Think it's the same for the ep3s that aren't type r?
@big_gooch1601
7 жыл бұрын
Isaac Avalos yea it's all fairly standard across most cars once the belt is slack it's a simple case of threading the belt around the pulleys. just go easy with the tensioner
What's the belt part number?
@big_gooch1601
5 жыл бұрын
38920-PRA-013. Providing yours has a/c and is pre facelift. You're welcome.
@jamiepudney
3 жыл бұрын
@@big_gooch1601 so helpful otherwise wouldn't of even thought of trying this myself but nw I will