Thank you so much man. I had to remove my distributor to access something below it, and since i have never done it before I did not know to mark it, and when i re-installed the car wouldn't start. Now i can sleep tonight knowing ill be able to fix this in the morning!

@ianagawa9795

4 ай бұрын

Hi, same here i could not start my car. Been days now i cannot start.. can you help?

I just pulled my distributor off to replace all the seals, cap, rotor, external ignition coil ect. Turned the shaft a whole bunch and didnt mark the head that goes into the engine when I pulled the pin and snap ring off. Now I have to do what you describe in the video to find TDC and then if it still wont work, flip the head on the distributor 180* with the pin and snap ring. 95% sure that will do so just leaving a like a head of time

Finally a thorough and detailed video that is actually helpful. Thank you!

I'm on a different Computer and I couldn't like your video and say how much I needed this information! I quickly grab my phone and went on and found your video and thank you brother I pray and bless you and hope everything going good in Jesus name Amen!

@wisemonkey1551

4 жыл бұрын

Happy it helped you. Please share and subscribe.

You're are insanely intelligent... Thank you for all the info. Fountain of wealth.. pure knowledge... I got all I need to get my job done Thank you

@voodooranger5772

2 жыл бұрын

6:09 😲

@marcus9x9

Жыл бұрын

Did you understand the timing mark after 8 min?

Just wanted to say thank you for this. I really appreciate your detailed explanation...I'm hoping this information can help get my car zooming again.

@wisemonkey1551

3 жыл бұрын

Much appreciated

You came in clutch with this video !!! Thanks!!!

@wisemonkey1551

4 жыл бұрын

Glad to help!

Thank u, FINALLY a video that explains wat I need help wit, thank u so much

Thanx for the video.. I have a p1381 code 01 accord. Hopefully this fixes the issue.

Wonderful video. My car wouldnt start because it was 180 degrees off. Thank you!!

@wisemonkey1551

4 жыл бұрын

Happy could help. Thanks for watching. Please share and subscribe.

@luciferjr4204

4 жыл бұрын

How did you fix it

@OGbqze

4 жыл бұрын

@@luciferjr4204 flip 180

@luismora5105

3 жыл бұрын

@@OGbqze my distributor only goes in one way

@OGbqze

3 жыл бұрын

@@luismora5105 I must have gotten lucky when I did it cause I just put my number 1 cylinder on TDC, aligned the rotor, and it popped right in and fired right up.

Thanks. Great video 🖤.. very helpful

Thanks for the info I will try this when I visit my car again

@cbdreamer1709

4 жыл бұрын

So funny. I know the visit feeling

thankyou for sharing your knowledge

On the pooper doing my research for my F ups lol thanks boss FL - Lakeland

Thank you so much!!!

Hi sir. How to diagnose fuel injectors fire at the same time?

What if it starts and drives, but turns off when you take foot off accelerator, did I do it correct or I need spark plugs or sum?

That "fork" each slit that the dizzy sits in are gapped differently everyone examine your motors i learned that the hard way to. Love the video tho I have a f20b dohc vtec boosted on hondata s300 looks just like my motor I painted my top hat (valve cover) deep gray

@wisemonkey1551

3 жыл бұрын

Not necessarily Shawn. Depends on the camshaft and model of the dizzy. I have few dizzy and none of them are what you are saying.

I think this is my problems with my 91 civic cranks but doesn't start but tbh i dont know how to fix this it has a d15b2 engine

Hey bro I have a question when you do the timing on the ignition for the distributor with the light gun do you have to ground out these one connections and bypassum I'm doing it on a Honda prelude 5th generation h22 the timing is reading at 16° cuz my tuner said it to that but the car takes a while to start up and before I had it on the whole in the middle but I don't remember what degree it was back then and he timed it without doing the connection bypass he just hooked up the light and didn't but I think he's not reading how it is

Thanks.

Thank you amazing

On the b series the dizzy fork has 2 different sizes on the fork. It wont fit the other way around. Is this different for h motors? There is no need to check the marks. Only use the marks to put on the belt on or check with your timing light

@wisemonkey1551

4 жыл бұрын

it goes both ways in H series. Horrible

Hi can anyone help me , my distributor on my 94 eg honda has no plugs on the distributor the wires are connected directly but there's no spark, it is only swinging...does anyone know how to wire the distributor without the plugs ?

I have the same engine and my distributor only goes in one way with the rotor facing the number 4 position. Am I doing something wrong? Thanks

@luismora5105

3 жыл бұрын

You ever figure it out same problem

I doing my first Timing on my 94 Prelude and if I could ask on what is that metal rod your sticking into cylinder one?

@wisemonkey1551

13 күн бұрын

just a long screw driver to determine the cylinder's position.

@wise monkey do I have to take out the distributor to adjust the timing for TDC

@wisemonkey1551

4 жыл бұрын

Not at all.

@rhino671

4 жыл бұрын

@wise monkey thank you I already subscribed

@marcus9x9

Жыл бұрын

Did you understand the timing mark?

Why go through all this work? It only goes in one way or turn it 180 degrees. What am i missing?

@marcus9x9

Жыл бұрын

the rotor can be in two ways, one is wrong. get it?

@ColtonLoberg

4 ай бұрын

Exactly? Also the cap wires are wrong? I don't understand this video am I missing something

Do I necessarily have to do timing or can I just line the notches up and wing it?

@jd364

2 жыл бұрын

How did it go? i was wondering the same

Do any one know if the camshaft position sensor is in the dizzy on a jdm h22a

@wisemonkey1551

13 күн бұрын

yes. Ckp cyp and Tdc are inside in the dizzy in a JDM h22a. Outside for h22a4.

What way do I rotate the ratchet?

@marcus9x9

Жыл бұрын

Did you understand the timing mark?

Really a very good video. I can follow you so well up to 8min. After that, I start to lose you. You said intake stroke vs exhaust stroke. Why did you say this? I don't think I understand. Doesn't TDC happen on compression and exhaust strokes? Are you trying to say it should be TDC on compression and not exhaust stroke? And the timing mark, at 1st it cannot be seen and suddenly it's obvious. How did you do that? You did not show.

I have the same motor and my car cranks but doesn't start and I'm thinking its the timing is off I have fuel compression and air and spark but it still doesn't want to start please help me thank you

@wisemonkey1551

4 жыл бұрын

Attach a nice thick ground wire one end bolted on to the engine head and other end to the Negative battery terminal and try to start again. This is easiest step before timing etc. Don't forget to subscribe. Cheers

@rhino671

4 жыл бұрын

Can I attach the ground wire to the chassis or to the valve cover

@wisemonkey1551

4 жыл бұрын

Below valve cover somewhere in the head and other end to chassis or negative battery

❤

Will this apply to all honda Engines? Or just H22A?

@wisemonkey1551

10 ай бұрын

all with a dizzy

1 million??? Buddy you better start putting mad work in lol. Gooooooood luck to you on that life journey I hope it works out for you .

@wisemonkey1551

4 жыл бұрын

Lol. True. But it may change too. Mad work is in the plan too. People like entertainment, not real work even if it is helpful.

@matthewbim10

2 жыл бұрын

@@wisemonkey1551 I liked the satire about the "hundreds of dollars" giveaway when you hit 1Mil. Good luck and thanks for the info!

@wisemonkey1551

2 жыл бұрын

@@matthewbim10 Seriously it will be, if not thousands of dollars. People just have to subscribe to expedite the process ...lol. Dont have much subs and thats a bummer

So I must have turned the 2 forks at the tip of the distributor so can I just take the distributor out and just turn the forks 180...

@wisemonkey1551

3 жыл бұрын

You can try to do the 180 move. Watch the whole video and it will tell you how to do from scratch too.

@kangokidkidd4037

3 жыл бұрын

@@wisemonkey1551 I did this I had a rag fly upward I could see the too of the cylinder.....lined up the top camshaft and still no crank

@wisemonkey1551

3 жыл бұрын

@KangoKid Kidd check that you have spark by taking a wire plug off and ground it to the exhaust or body and crank. Or just use a light to test if you have one. Number 1 cylinder is the furthest from the dizzy. You need to - 1. set #1 to top dead center. 2. Check timing marks to verify its TDC. 3. Have the dizzy rotor face the right pole (#1). 4. Make sure there is spark of course. 5. You must have a known good dizzy.

@wisemonkey1551

3 жыл бұрын

you can try that. also watch the entire video carefully, it will tell you all the steps. make sure you have spark going through the plugs wires.

Your cap is the wrong firing order? Bottom left is 1, to the right is two Top left 3 then 4 top right

@wisemonkey1551

4 ай бұрын

There are few version of this engine. You are comparing it to a wrong one. I checked every cylinder by rotating the engine. It is correct and the car runs fantastic putting about 220hp out.

Hi Sir so I just replaced the oring on the distributor went to crank it up and it will not start what the heck happened

@luismora5105

3 жыл бұрын

You figure out the problem

@kangokidkidd4037

3 жыл бұрын

@@luismora5105 I had to to line up the timing only on the cam shaft

@ianagawa9795

4 ай бұрын

Have you resolve this? How

The dizzy has a scribe mark on the cog no need for DTC just take the old one off line up the scribe mark with the one you took off and ur ready to go

@wisemonkey1551

4 жыл бұрын

No don't be fooled by the scribe mark

It can only go in one way....

Am i the only one who found this confusing? Which direction do you really install the rotor

Good video but idk about the million subscribers handing out a 100 Dollar prize with 1 and a million chance of winning for a hundred bucks and your making bank off videos with that many subscribers. Bring that prize up some

@wisemonkey1551

4 жыл бұрын

Never said $100 bucks as prize. Intention is to give a lot more....

I'm sorry man but you made a 3 minute into a 12 minute video... but thanks I guess.

Y’all are hyping this guy up when he isn’t intelligent! You cannot install the distributor 180 degrees off, it may sorta look like you can, however the slot is offset, and always has been. Next he’s using wire twists. No decent auto repair facility would ever hire someone who’s work looked like a cave man did repairs. If you dropped this car off at the dealer and after picking it up you opened the hood and saw this, you’d be wow these people are intelligent??? No you wouldn’t

@wisemonkey1551

Жыл бұрын

you have not seen enough of camshafts or dizzy boy. This installs 180 off without a struggle. TD61U on H22A JDM cams. Ever hear of this Dr. Lee? lol.

@g2integy

Жыл бұрын

Yeah he messed me up also