I'm about to up grade my 98 firebird formula's front and rear suspension and drilled and slotted rotors! I'm doing my homework because I got it brand new in highschool! Don't want to mess the shit up 😢, good video thanks

what a great video and camera work,i am now convinced i aint doing mine

@klowny1969

Жыл бұрын

Thanks..don't forget to subscribe

Thanks for continuing to make great videos! Always lots of good info and tips

@klowny1969

Жыл бұрын

Thanks for watching!!

I got that, bitch of a, bolt out using a T50 bit and a box end wrench with a swivel! Thanks for your knowledge and time babyyyy!

@klowny1969

6 ай бұрын

Thanks for commenting and watching..don't forget to subscribe 😉

After you install both struts, aren't you suppose to get a wheel alignment? From a shade-tree mechanic 😮

Comments were right.. best vid out here..

@klowny1969

Жыл бұрын

Thank you..don't forget to subscribe

Thanks for the video, really helpful 👍 but I love the 12pack of Coronas,.y kind of beer after a job well done 👏

@klowny1969

5 ай бұрын

Thanks man..don't forget to subscribe 😉

bro this was so helpful. the assembly instructions from KONI are literally worthless lol

@klowny1969

Жыл бұрын

Yes they are! Thanks for watching and don't forget to subscribe and hit that bell

Great job 👍 Klowny

@klowny1969

Жыл бұрын

Thanks for stopping by again!!

The "from behind babyyy" made me go woooooo!!!! Already know!

@klowny1969

10 ай бұрын

Oh yeah!!!

Butta sauce 😂 deez nuts NY licences plate😂

@klowny1969

Жыл бұрын

Yeah baby!!

Great video. But I have different question. I have a 2002 v6 convertible and wanting to do an LS swap. Will any subframe from a 4th gen camaro that had a v8 work. Someone told me it would not because my car is a convertible. Thanks.

For the tools needed for this job, do I have to use Coronas or can I use Tecate??

@klowny1969

Жыл бұрын

Whatever mexican beer works for you my friend

@zaknefain100

Жыл бұрын

you don't want the 'rona... stick with the Tecate.

@michaelslack6891

6 ай бұрын

DOS XX babyyyy!

Hello, any tips on raising the front suspension?

@klowny1969

11 ай бұрын

You can do coilovers..don't forget to subscribe

I had the same problem with the Mevotech strut mount and the hardware spinning. I also found out the hard way that the studs on the Mevotechs are not long enough to run a strut tower brace and also a Strano master cylinder brace. I ended up using the Monroe version of the strut mounts; I also tried the Moog part they were garbage in my opinion, first time a Moog part disappointed me. Food for thought.

@klowny1969

Жыл бұрын

Yeah moog has turned into crap

I was waiting to that pry bar to go into your buddy's hand. I appreciate your video, but Children do not do it like this at home.

@michaelslack6891

6 ай бұрын

Children working on cars? Maybe your mom can do it

Nice job. Clean car!

@klowny1969

Жыл бұрын

Thank you sir

👑

butter sauce👍

@klowny1969

Жыл бұрын

Yeah baby

I appreciate all the great videos Klowny but a couple helpful notes on this job to try the next time. Just loosen the master cylinder. It doesn't need to come off. The caliper doesn't need to come off either, just support the whole rotor assembly with something underneath. You should never use a power tool on that top bolt for the shock on a Koni. There's a notch on the shaft to hold it with an open end so it doesn't spin as you tighten the nut, over time it may come loose doing it that way and you'll develop a clunking noise or may even damage the mount, at least give the nut a couple turns while holding the shaft after using the power tool. To free the spindle you don't need a ball joint puller, just tap both sides at the same time with a hammer in each hand and it pops right out with a few small taps.

@klowny1969

Жыл бұрын

Thanks for commenting

@sanatanababaji2809

9 ай бұрын

I am going to have it done, too much trouble for an amateur.

Having trouble with right side not lining up with the car any tips

@klowny1969

Жыл бұрын

Sometimes you gotta take it out and put it back in

Would this work the same for the 3rd gens firebird’s?

@klowny1969

Жыл бұрын

No that's a different setup

Hey buddy question , how much would you charge the customer for this job ?

@klowny1969

Жыл бұрын

Couple hundred

Let it fall on the freakin floor baby!

@klowny1969

Жыл бұрын

Yeah baby

@Highlander1432

Жыл бұрын

@klowny1969 Hey what part of NY do u guys live ? Love the videos btw

4:18 I was waiting for the tool to break, probably made in China.

@klowny1969

Жыл бұрын

OTC tool..they always pop like that lol

How the heck u just twist them bolts put mime are locked :(

@klowny1969

Жыл бұрын

Which bolts?

@williamSLIT

Жыл бұрын

@@klowny1969 t50 torx bit :/

I hope that spindle didn’t bonk you on your clown nose!

@klowny1969

Жыл бұрын

It hit my camera girl in the face :)

@michaelslack6891

6 ай бұрын

Everything good butter face!

Those are shocks. Not struts

@klowny1969

5 ай бұрын

Struts..don't forget to subscribe